Search Documents

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016

By Robert A. Macinnes, Peter Moon, John P. Pappone

"This paper, in presenting the results of the application of the assessment centre method at Texasgulf Canada Ltd., illustrates a novel "" in-use"" technique for manpower training in the mining industry.IntroductionMining history is full of examples of what goes wrong when human judgment fails-disasters, floodings, loss of life and property. We must, therefore, assume the importance of selecting competent people for supervisory responsibility. This article de scribes a method for assessing supervisory ability, its first application in Canadian mining and the result s obtained over the past six years. It is known as the assessment centre method."

Jan 1, 1981

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By D. du Plessis, R. Stobbs

The Canadian Clean Power Coalition (CCPC) was created in 2001 to protect and enhance Canada’s vast coal and other carbon-based resource wealth, and to ensure that environmental public policy decisions recognize that these resources are a Canadian asset, not an environmental liability. To achieve its mandate, CCPC has undertaken to demonstrate technologies for use in new coal-fired power plants to control air emissions including carbon dioxide (CO2), nitrogen oxides (NOx), sulphur dioxides (SOx), mercury (Hg), and particulates (PM). The first phase of the demonstration project assessed three existing technologies for coal-fired power plants that reduce all emissions, including CO2, to levels equivalent to or below that of gas-fired power plants. The technologies considered in this phase included integrated gasification combined cycle (IGCC), ‘oxyfuel’ combustion, and amine scrubbing of pulverized coal. These technologies were evaluated with three coal types: Eastern bituminous, western sub-bituminous, and lignite coals. This paper presents the studies, conclusions concerning the capital and operating costs of these technologies, the cost of electricity produced (with CO2 removed), and the cost per tonne of CO2 avoided. It also discusses the potential for using captured CO2 for enhanced oil recovery, and possible technology enhancements for improving the competitiveness of gasification of low-rank western Canadian coals. The second ongoing phase of CCPC’s work includes the design and construction of a commercial-scale plant to demonstrate the feasibility of integrated gas combined cycle (IGCC) and/or polygeneration technologies and the potential for using the CO2 generated for enhanced recovery of conventional oil.

Jan 1, 2006

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014

By J. Lee

As the usage of BIM increased in the construction industry, some construction owners started exploring the use of BIM for maintaining their facilities. Construction Operations Building Information Exchange (COBIE), a spreadsheet data format suggested in 2007 to manipulate building information, is considered as one of the solutions that would facilitate the process of transferring information from BIM to applications for facilities management. Several BIM and Computer Aided Facilities Management (CAFM) applications offer functions to export or import the COBIE data. To facilitate the process of generating the COBIE data out of Building Information Model, some add-in applications, such as COBIE Toolkit for Revit, also were developed. However, most of these applications handle a limited amount of COBIE data. Professionals using these add-in applications therefore sometimes end up spending a significant amount of time to add additional data manually to the COBIE data file. To automatically get a data-rich COBIE file, we developed a prototype application that extracts information from Revit, which is one of the BIM authoring tools, stores them in an external database, and then produces the COBIE file using information stored in the database. We applied our application to a pilot project and produced 8 COBIE worksheets automatically, which demonstrated a significant amount of time saving. This paper presents how our prototype application produces 8 COBIE data sets automatically. It also addresses our attempt to handle more COBIE data sets.

Aug 1, 2013

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By P. Dauphin

"CANMET’s Mining and Mineral Sciences Laboratories have developed the Canadian Mining Technology Network (CMT-Net), a website to provide industry with up to date information on technologies in several areas. This paper gives background on the Mineral and Metal Processing sector, describes the steps leading to the development of the websites strategy and gives a tour of CMT-Net. IntroductionThe government of Canada is developing a strategy aimed at fostering the development of value-added activities in the area of mineral and metal processing (MMP). Natural Resources Canada (NRCan) and Industry Canada will partner in delivering on this strategy. Instrumental in defining the main thrusts of the value-added strategy was a series of consultations held across Canada with representatives of companies and organizations active in the sector. The objective of the consultations was to identify barriers to the development of activities which add value in the sector, as well as point to positive factors.Following the consultations, a discussion paper was produced, “From Mineral Resources to Manufactured Products: Towards a Value- Added Mineral and Metal Strategy for Canada” (Natural Resources Canada, 1998). The paper reviews the sector’s structure and main statistical information, lists some of the positive factors and barriers to value-added activities and defines a new partnership between industry and government that will lead to more valueadded activities. The main objective of the paper is to serve as a discussion document between stakeholders during the development of the strategy."

Jan 1, 1999

By D. A. Barr

High-grade gold-silver mineralization associated with electrum and argentite was discovered in a quartz vein at the Chappelle property, 273 km north of Smithers, B.C., in 1969 following a regional geochemical reconnaissance program in the Cassiar-Omineca Mountains. Subsequent exploration resulted in the discovery of numerous quartz veins with associated precious-metal values in a belt 17 by 3 km in area centrally located within Toodoggone Group volcanic and sedimentary rocks of Lower to Middle Jurassic age and a window of Takla Group volcanic rocks of Upper Triassic age. More detailed investigations, consisting principally of 5677 m of surface drilling in 57 holes and crosscutting, drifting and raising on Chapelle Vein A, has outlined a high-grade gold-silver-bearing shoot with a strike length of 200 m, an average width of about 3 m and extending to an average depth of about 40 m below surface.

Jan 1, 1978

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By James J. Holmes

ACCIDENT prevention as we know and understand it today is of comparatively recent origin. As a matter of fact, the Industrial Accident Prevention Association of Ontario, which is the oldest organization of its kind in the Dominion, celebrated its thirtieth anniversary only this year. On the other hand, one could say that the history of accident prevention is almost the history of mankind itself. In a general sense, every forward step that man has made throughout the centuries has been largely due to two things: (1) a desire for increased comfort, and (2) the need for safety; and, always, the need for safety has taken precedence over the desire for comfort. While it is true that hundreds of volumes have been published, dealing with the many aspects of accident prevention work, you cannot go to a library and pick out a book that has all the answers in it. Such a book has never been published-we are still looking for some of the answers. However, a good deal of real progress has been made.

Jan 1, 1945