Search Documents

By K Schonert, K Eichas

Electrostatic separation of non-conductive materials can be accomplished by triboelectric charging. The efficiency of convential separators becomes worse in the size range below about 100 ¦m. These problems are solved by developing a new double-drum-separator. The investigations have shown the possibility of separating very fine mineral mixtures (eg quartz/calcite) in a strong electric field after tribo-charging in a special dust-feeder. The paper reports about the influence of particle size and field intensity on the separation and deals furthermore with the problem of desagglomeration.

Jan 1, 1993

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Brown

With oxygen conditioning routinely used in both the lead and zinc circuits at Pasminco Elura Mine a more sophisticated method of determining oxygen demand was required. It is known that different ore types have different oxygen consumption rates, however oxygen is added at a fixed rate regardless of ore type in the plant. Therefore, a simple laboratory test was devised to measure the oxygen demand of ores. The paper describes the technique employed, and provides an interpretation of the results. These data, together with pulp chemical measurements (Eh, pH and EDTA extraction data) were correlated against laboratory flotation performance to establish the relationship between oxygen demand and the position of the grade/recovery curve.

Jan 1, 2000

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By I R. F MacCulloch

Bacterial oxidation of sulfide minerals is a familiar and commercially available process to enhance gold recovery with problem ores. Pintail Systems, a Colorado, USA based company had developed bio-processes for gold recovery based on natural mineral formation and transformation in a global mineral cycle. The biological recovery of precious metals from ore involves a number of mechanisms that are dependent on the metal-mineralogical association. These processes include: partial bio-oxidation of sulfide ores; oxidation of gangue minerals exposing gold to leaching; surfactant properties of bacteria/nutrient solutions that improve wettability of ores and solution contact with leachable gold and silver; and microbial production and excretion of trace amounts of gold lixiviants, and bio-fracturing or biological alteration of ore minerals. Pintail has demonstrated enhanced recovery of precious metals during cyanide detoxification of spent heaps at the end of mine life. Biological recovery processes also have the potential to be applied to in situ mining technologies. The in situ process application could recover gold from subgrade deposits, small deposits or those ore bodies with uneconomic stripping ratios for conventional mining. In situ biomining can be accomplished at a fraction of the cost of conventional mining and leaching and does not have the environmental liabilities associated with many conventional gold lixiviants.

Jan 1, 2004

By J Thoma, W Skinner, W Stewart, R Smart

The acid neutralisation capacity (ANC) of rock sample containing significant iron carbonates and/or reactive framboidal pyrite can be a difficult parameter to determine. Results indicated that negative ANC results can occur if reactive sulfide minerals are present; and an over-estimation of ANC will result if significant Fe rich carbonate minerals are present during industry standard ANC tests. In this paper we investigate these problems. Results showed that a significant lag period may be needed (up to 432 hours) after standard Sobek ANC type tests of siderite for the complete hydrolysis of iron released from this mineral. This even occurred with standard industry modifications that included the addition of two drops of hydrogen peroxide. In this work we use a modified Sobek test that included filtering, and thence continued hydrogen peroxide addition until there was no subsequent pH drop, followed by back titration to pH 7.0. Results indicated that the ANC for the siderite (after zero hours) was immediately comparable to the ANC determined after 432 hours lag by standard Sobek type tests; and a calculated theoretical carbonate ANC. Investigations of coal waste samples containing significant framboidal pyrite indicated that standard Sobek ANC type tests can result in negative ANC values due to the oxidation of this reactive pyrite. Because sulfide acidity is already addressed by the MPA calculation, the inclusion of sulfide acidity as part of the ANC determination is effectively biased towards acid generation and thus positive NAPP values. Negative ANC values cannot be ignored or assumed to be zero as this masks any actual ANC available within the sample, which may possibly affect AMD categorisation. This sulfide acidity can be factored out using the quantity of S in the ANC digestion liquor and knowing the non-acid generating sulfate content of the sample prior to ANC testing. Results indicated that incomplete iron hydrolysis at the completion of the Modified Sobek ANC test is not only a function of iron carbonate dissolution, but is also related to the dissolution of Fe-sulfate salts, and the oxidation of reactive sulfides such as framboidal pyrite.

Jan 1, 2003

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

By Griffin PT, Espinosa-Gomez R, Jameson GJ

Two major issues are to be addressed in the Copper Concentrator of Mount Isa Mines Limited. The first of these is the need to increase concentrator flotation capacity to increase copper recovery, while the second is the need to reduce the iron sulphide dilution to meet future smelting requirements. Extra capacity in the cleaner and retreatment sections of the concentrator have been identified as key target areas, with additional copper recovery of at least one per cent identified from plant trials. Extensive pilot plant tests have been undertaken to evaluate the performance of the Jameson cell compared to conventional mechanical cell and column circuits. This work has shown that Jameson cells present an opportunity to achieve the desired grade and capacity specifications at lower capital cost than available alternatives. This paper outlines metallurgical results of work undertaken in the Copper Concentrator, together with a summary of pertinent Jameson cell operating parameters investigated during the period.

Jan 1, 1993

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By J Rutter, E Amini, D La Rosa, N Beaton, M Scott, F Faramarz, L Keeney

Anglo American’s Los Bronces copper mine in Chile has been conducting detailed assessments investigating value adding options for their asset. The mine has conducted several detailed Mine-to- Mill and Grade Engineering studies to investigate increased throughput and head grade and to quantifying the impact of these approaches across the life of mine. CRC ORE has two key technologies namely Grade Engineering and the Integrated Extraction Simulator. These two technology suites have been combined to understand the technological landscape and associated value drivers suitable for application at Los Bronces. Detailed ore characterisation test work was conducted to:  measure and spatially model the propensity of ores to naturally deport and  develop customised blast models for Mine-to-Mill and Grade Engineering evaluation The outputs of this work were utilised to develop a block model populated with a range on new Grade Engineering and blasting parameters suitable for scenario analysis. To facilitate scenario analysis a high-fidelity value chain model of the Los Bronces operation from blasting to concentrate production was built in IES. IES was combined with sophisticated analytical tools such as Neural Networks to develop and reconcile a fully integrated value chain. The value chain model made it possible to simulate in IES all available blocks in the block model to predict throughput and grade changes for different strategic scenarios. The scenario analysis was run across 24 strategic combinations of Mine-to-Mill and Grade Engineering and comprised several million simulations. The scenarios investigated each technology independently and jointly to provide an attributed block model that can feed forward into technoeconomic modelling to determine optimal execution strategies for the mine. This paper presents the first published study combining Grade Engineering and IES to provide mass simulation capability to investigate strategic options for a mining asset.

Nov 10, 2020

By G W. Wilson

Net solar radiation is one of the key factors affecting evaporation from soil covers on waste rock dumps. While net solar radiation is normally taken as a uniform parameter over a site for modelling purposes, there can be significant variation in the radiation actually received on various portions of the dump. These variations are a function of the difference in the cover slope and direction of exposure. A predictive model has been developed to calculate the actual radiation received on the dump surfaces, based on the net radiation data measured at a weather station on a horizontal surface. The model has been designed for application at any mine site in the world, and can be used in conjunction with evaporative flux models to help estimate the effect of three-dimensional variations in the cover surface exposure. The waste rock dump at Equity Silver site (located in British Columbia, Canada) has a barrier-type soil cover system to limit oxygen entry and water infiltration. This cover has been monitored for the past nine years. The new net solar radiation model has been applied to this site and the predicted net radiation was compared to the values of actual net radiation measured on the site. The predicted variations in net radiation over the three-dimensional surface of the waste rock dump have been applied to calculate spatial variations in potential and actual evaporation (or evapotranspiration) from the site. Preliminary analyses indicate actual evaporation from a site at this latitude could vary by a factor of two for exposed versus shaded slopes. The implications of these variations for the site are considered.

Jan 1, 2003

By S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

Uncertainty about the future and orebody should significantly impact evaluation of mining projects. Scenario planning, widely used in other industries, for example in the petroleum industry, can provide organisations with an opportunity to explore the consequences of uncertainty on their future plans. By developing plausible scenarios, scenario planning assists decision makers by allowing them to make systematic and possibly effective decisions for the future. This paper reviews existing mine project evaluation in the context of a new framework called scenario-based project evaluation (SBPE) (Vann et al , 2012) that addresses many shortcomings of existing approaches. SBPE uses conditional simulations (CS) models as inputs which are evaluated against future alternative project pathways (æalternativesÆ). These alternatives are evaluated using multiple plausible images of the deposit (CS realisations) which capture realistic variability and as an ensemble, map uncertainty of various orebody attributes at fine scale. The alternatives can involve different mining, stockpiling, blending and processing strategies. The ultimate output is a (stochastic) set of cash flows for each alternative from which financial measures, such as NPV, can be derived. Alternatives can then be explored in the presence of against external scenarios such as changes in prices, costs, and taxation. The obvious problem with such data rich results is knowing which scenarios or group of scenarios are optimal.An innovative approach to robust stochastic optimisation (RSO) suited to the SBPE framework is presented here for the first time. This approach to RSO aims to deal with the large number of alternatives generated from SPBE. The goal of applying the RSO approach to SBPE is to identify robust strategic alternatives (project configurations) which have the flexibility to deal with variability and uncertainty of geological and processing inputs such as density, grade and process performance. By applying the proposed RSO method, it is possible to deal with uncertainty and identify the best project configuration in the face of a large number of envisaged scenarios. A case study is provided, in which we have tested the application of the proposed method and compared the result with conventional methods. An important conclusion from this research is that selecting the value of the penalty coefficients in the RSO approach proposed is (as is all optimisation) an exercise of trade-offs; a higher net present value (NPV) is generally associated with a higher risk and a lower risk is associated with a lower NPV. Indeed, this is a strong argument for considering the RSO approach outlined here over more conventional approaches.CITATION:Moayer, S, Vann, J, Coward, S, Jackson, S, Bye, A and Wolff, R, 2012. An innovative approach to robust optimisation for scenario-based mineral project evaluation, in Proceedings Project Evaluation 2012 , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By D Duan

In this study, aimed at two kinds of ore (lump ore and iron ore fines) and four types of Australian iron ore resources (haematite iron ore, Mara Mamba iron ore, limonite iron ore, and mixed iron ore, such as Newman, MAC, Yandi and Pilbara iron ore), the physical and chemical properties and high-temperature properties were investigated in detail, to master their behaviour and effects in sintering, blast furnace, and non-blast furnace processes. Then, according to the individual properties of Australian iron ores, Chinese domestic iron ores and Brazilian iron ores, etc, the optimisation of ore-proportioning for sintering, blast furnace, and non-blast furnace processes was studied based on the interaction of the individual iron ores and their complementary properties, and the corresponding tests were carried out. The test work results indicated that this method not only improved the technical and economic indexes of sintering, blast furnace, and non-blast furnace processes, but also increased the addition of Australian iron ore. All of these provide the theoretical basis and technical support for highly effective use of Australian iron ore resources in iron and steel enterprises in China.

Jul 11, 2011

By Mizuta T, Sakurai M

The Pine Creek Inlier produced 12 440 kg of gold in the period from the first gold discovery in the 1860s to the early-1900s. During the 1930s renewed large-scale prospecting took place and gave a foothold for today's gold mining operations. The rise of the gold price and improved mining methods in the 1970s and 1980s made possible low cost, bulk low grade mining operations. Various gold deposits including vein, network and stratiform types occur in the Pine Creek Inlier (Nicholson and Eupene, 1990). The Tom's Gully deposit is located 100 km south-east of Darwin in the Northern Territory. It is hosted in the early Proterozoic Wildman Siltstone and lies north-east of 1800 my old Mt Bundey Pluton (Figure 1). Around the Mt Bundey Pluton, there are several prospective base and precious metal deposits such as Quest 29. The Tom's Gully gold deposit was discovered in 1986 and yielded a total of 3070 kg of gold from ore averaging 9.35 g/t gold between 1987 and 1990 when the mining operation was terminated.

Jan 1, 1994

By N Eriksson

BolidenÆs Aitik mine, located 100 km north of the Arctic Circle in northern Sweden, is one of EuropeÆs largest copper mines. This operation produces 18 Mt of ore per year and 99 per cent of this tonnage needs to be deposited as tailings. The tailings pond currently covers 1140 ha but at closure it will hold around 760 Mt of tailings and occupy an area of 1400 ha. The tailings contain less than one per cent sulfur and only 0.03 per cent copper. The carbonate content is as low as 0.25 per cent but silicates, with substantial accumulated buffering and metal adsorption capacity, are abundant. A programme of comprehensive material characterisation and investigations has been undertaken in order to design a decommissioning strategy that meets the regulatory requirements and secures long-term physical and chemical stability of the deposited tailings. The main concern has been the potential generation of acid rock drainage (ARD). Standard tests using acid base accounting (ABA) and humidity cell tests during 15 weeks were not conclusive regarding the ARD generation potential. The accuracy of the results was considered to be unsatisfactory, therefore the humidity cell tests were gradually extended in time. In total, almost four years of humidity cell tests were conducted on various sets of samples which were selected in order to cover the variation in sulfide content existing on site and in various points of the milling process. The laboratory results were subject to detailed geochemical evaluation in order to fully understand the interaction between acid-producing reactions, driven by weathering of sulfides, and acid-consuming reactions by dissolution of carbonates and alumino-silicates. The laboratory tests were followed by both pilot tests and field measurements in order to estimate the scale dependency between the laboratory and the field results. It was found that sulfide weathering rates in the field were considerably lower than those measured in the laboratory. However, it could not be verified that the tailings top layer would maintain a neutral pH in the long term even under field conditions. Thus, a reviewed tailings management plan, including de-pyritisation of the tailings during the last years of operation, is considered.

Jan 1, 2003

By Hoberg H, Schneider FU

The stability of suspensions can frequently be controlled only by the use of supplementary polymeric agents. Such methods date back to the time of the ancient Egyptians, who used natural rubber as a deflocculant for carbon black in the manufacture of ink (Anon, EncyclopediaBritannica, 1968). Since the development of synthetic polymers in the 1950s they have been deployed in all manner of applications. Indeed the mining and paper industries as well as industrial or communal waste water treatment plants are largely dependent on flocculants which make a major contribution to the relief of the environment. As some of the polymers used are carried out from the process via purified water, problems can emanate from the application itself as long as no reliable data is available as to the exact whereabouts of the polymers and their impact on the biosphere. In order not to invade other systems, they would have to be biologically degradable which has not, until now, been confirmed (Blockhaus, Sequaris and Schwuger, 1991; Schumann, 1991). It has, however, previously been demonstrated (Hoberg et al, 1990) that when process water circulates in mineral processing operations, residual amounts of polymeric flocculants can have extremely adverse effects on the selectivity of flotation processes. The adsorption behaviour is consequently one of the most important considerations in the development of new polymers, the aim being to minimise the amount of non-absorbent matter. The objective of the investigations carried out on ampholitic synthetic polymers of high molecular weight to be reported on here was to permit the connection between settling index and adsorptivity to be characterised in greater detail. As the level of knowledge concerning flocculation and polymer adsorption in real systems is still limited in spite of numerous practical and theoretical studies in this field, the experiment was designed to be relatively broadly-based. As well as investigating various raw materials, an attempt was made to compile results on the influence exerted by different surface charges.

Jan 1, 1993