Search Documents

By M Dohm, L Pretorius

This paper provides a brief historical background to the approximately 12-year project that led to the revision of rope selection factors in the South African regulations, thus providing the ability to hoist economical payloads from single lift ultra-deep shafts. The efforts over the past 20 years have led to the revision of the legislation pertaining to rope selection factors, the redesign of rope constructions to meet the required duties associated with ultra-deep shafts, codes of practice for the design, operation and maintenance of winding plants, and a code of practice for the condition assessment of winder ropes. As a consequence the Moab Khotsong ultra-deep hoisting system could be developed and installed, with the assurance of predictable performance. Access to deep orebodies by means of single lift, ultra-deep shafts has a critical impact on the life cycle costs and efficiencies of ultra-deep mining complexes. A brief description of the main components of the hoisting system at Moab Khotsong is presented. An in-depth review of the development process applied to ensure a stable, safe and cost-effective rope construction for the ultra-deep Moab Khotsong shaft follows. The paper concludes with an overview of the experiences gained during the installation and commissioning phases of the winder, as well as operational and maintenance issues.

Jan 1, 2005

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007

My roots span four generations. My great grandfather, Christian Frederick Fisher, along with twenty-one others was drowned in the New Australasian mine disaster at Creswick in Victoria in 1882. My grandfather, also named Christian Frederick Fisher, escaped and then followed a career of shaft sinking for large companies and operating small mines (very unprofitably according to my father) when funds allowed. My father, an excellent practical mining and mechanical engineer, was also a small miner and my early entry into the industry was, like many before me, very basic. My introductions to the business end of a No. 4 shovel, drilling with hand steel and later with jack hammers without the benefit of airlegs, feeding heavy cordwood to hungry boilers and felling trees for mine timber soon dispelled any illusions I had that mining was a bed of roses.Before it became well known I knew "Life was not meant to be easy".In a family-owned small gold mine in a remote part of Cape York Peninsula in far north Queensland I was fortunate in obtaining an excellent grounding in reef and deep alluvial mining. Operating in vertical and underlie shafts the variable ground conditions often required close timbering. Steam pumps were used underground and steam winders for hoisting.The complete absence of municipal or government infrastructure in this remote mining field threw responsibility on each mine operator to be self-sufficient, and responsible for mine development and installation of crushing and milling equipment, accommodation and water supply. Conditions, although harsh, were acceptable in the 1930s, and fostered great self-reliance.The first crushing from our Black Cat Mine in 1935 returned nearly 200 oz from 10 tons of ore. Gold was then worth $13 an ounce compared to about $400 an ounce today; but in those depression years of the 1930s our operation was profitable.This basic education not only returned dividends when confronted with difficult mining problems, but created a deep respect for the miners who develop the small mines and who continue to contribute to the industry today, often under difficult conditions.Australia and mining are synonymous. The industry has been immortalised by the famous historian, Professor Geoffrey Blainey, in his book "The Rush that Never Ended".Initial gold discoveries were concealed and exploration was frowned upon by authority as being disruptive to early rural development. But with the discovery of gold in the Bathurst area of New South Wales by Hargreaves in 1851, the rush to the gold fields began followed by an influx of migrants. The traumatic effect on industry and society that followed, created the pattern of the love-hate relationship that at times became temporarily submerged, but is so evident today.In the harsh economic climate of the 19th century with low wages and no welfare, the opportunity to wrest riches from the earth was literally "rushed" by the adventurous, the poor, the rich, people from all walks of life. Pressures developed on preFederation Governments to provide law, order and infrastructure to the rushes that have never ended.

Jan 1, 1984

By McGhie R. R

The general structural features and the principal mineral relationships of the Black Star ore body, Mount Isa, Queensland, have been described in several previously published papers. But particular reference may be made to the work of Grondijs and Schouten, whose examination of over 200 polished sections revealed some remarkable features in the process of ore deposition. The observations by the present authors are based upon the study of a smaller ·set of specimens complementary to those examined by Grondijs and Schouten and are intended to elaborate certain aspects of the mineral relationships, more particularly those affecting the ore-dressing processes.The work described applies to the primary sulphide ore only, and to the present milling practice of fine-grinding and selective flotation.GEOLOGICAL FEATURESThe Black Star is one of several economic mineral concentrations in the Mount Isa series of thinly bedded carbonaceous shales, which are considered to be of preCambrian age. The nlineralization is apparently connected with pegmatite intrustions located within some miles of the ore bodies, and has been Gontrolled in the main by major folding of the shales and by a shear system which follows approximately the strike and dip of the beds. The detailed "The investigations described in this paper were made in the Metallurgy Department, University of Melbourne, where the senior author was formerly Senior Lecturer in Mining and Metallurgy. A report on a section of the work was submitted by the junior author as a thesis requIred by the University of Queensland.

Jan 1, 1939

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By W J

Al ores arriving at the works which contain more than 3% sulphur, together with all sands and other fine residues, are delivered to the roasting department. Those that are in a coarse condition are first sent to the crushing plant, consisting of 15 in. x 9 in. jaw crushers and two No. 5 Krupp mills. The ore is here crushed through a quarter mesh screen. Any pyritic concentrates high in sulphur are given a preliminary roasting, to bring the sulphur contents down to about 12 % and the roasted material is delivered to the H. H. charge-making bins. Here the various ores, sands, residues, roasted pyrites, together with about 12 % of limestone, are made up into I-ton charges in hopper trucks with bottom discharge. The trucks are elevated by hydraulic lifts to a tramway running over the roasting furnaces, and the contents are dropped into hoppers over each furnace, from whence the mixture is fed into the centre of each furnace by means of a Challenge ore-feeder.

Jan 1, 1918

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By Voss Smith F, Matters C. W, Slee R. T, Coldham JC, Davies HW, Wallman H. H

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs. J. O. Moulden, Howchin, Twelvetrees, and the West Australian Geological Survey for various information; to Messrs. J. G. Dreyer, S. Pope, T. Read, P. Moncrieff, R. Williams, and W. J. Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of the Melbourne University, gave much valued assistance in petrology, and Mr. Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-first for, silver, then for silver and lead, and at present for lead, silver, and zinc. No excuse seems necessary for placing before members even an imperfect report on the geological features of this notable ore deposit, since so little work has been done on the subject as to constitute almost a national reproach. This is the more deplorablesince the evidence laid open by mining operations is destroyed almost as soon as it is exposed, and there exists the real need of a continuous and connected record of geologieal developments.

Jan 1, 1911

By K Nguyen

The advances in computerised processors and digital microscopic imaging have enabled more studies that attempt to quantify textural information from rock images. However, a texture classification system designed for geometallurgy has always been challenging, as it combines general image analysis techniques and specific texture classifications in terms of the size, shape and orientation of mineral particles. In this paper, a novel texture analysis technique using grey level radial shell association (GLRSA) and spectral angle mapper (SAM) to discriminate between different geological images is outlined. The technique can be applied in routine analysis and characterisation of mineralogical and textural attributes which may correlate with variability in mineral processing behaviours. Using this texture analysis technique, a set of small texture reference images, a texturelet reference library, has been identified from a suite of drill core images. Rock types are classified according to the proportion of each texturelet type recognised. The library is site specific.CITATION:Nguyen, K, 2013. A new texture analysis technique for geometallurgy, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By O N. Antzutkin, W Forsling, K J. Pike an

The adsorption mechanism of three different O,OÆ-di-alkyl-dithiophosphate (dtp) collectors, K[S2P(OR)2] with R = Et, i-Bu and i-Amyl, on the surface of synthetic chalcocite (Cu2S) was studied by means of solid-state 31P CP/MAS NMR spectroscopy. The morphology changes on the conditioned Cu2S surfaces, in the collector concentration range 0.1 - 10 mM, were also monitored with scanning electron microscope (SEM). In order to assign Cu(I)-dtp species on the surface of Cu2S, the corresponding bulk Cu(I)-dtp compounds, which are clusters of the monovalent copper containing either Cu6(antiprismatic) or Cu8(cubic) cores, were synthesised, and characterised by means of solid-state 31P CP/MAS and static 65Cu NMR. Further investigations on the crystal habits of the bulk systems were carried out by powder x-ray diffraction and SEM. A comparative analysis of the 31P chemical shift and chemical shift anisotropy (CSA) data estimated from the experimental NMR spectra of the polycrystalline bulk Cu(I) dialkyldithiophosphate complexes was used for assigning the 31P resonance lines in the NMR spectra of the collector treated Cu2S powder samples. The species formed on the synthetic Cu2S surfaces were assigned to polycrystalline phases of: Cu6L6 with L = Et2dtpû, Cu6L6 and Cu8L6(S) with L = i-Bu2dtpû, and Cu8L6(S) with L = i-Amyl2dtpû. A heterophase autocatalytic step process of both formation and growth of solid CuxLy (L = R2dtp, x = 6 or 8 and y = 6) complexes on the collector treated Cu2S surface is proposed. A possible role of the oxidised form of dithiophosphate collectors, bis[di-alkyl-thiophosphoryl]-disulfane (disulfide), is discussed in terms of a specific self-redox reaction. The second order quadrupolar lineshapes in 65Cu NMR spectra were simulated and the interaction parameters, CQ and hQ, for the bulk dialkyldithiophosphato-copper(I) complexes were obtained.

Jan 1, 2005

Early theories of coal formation are outlined, with special emphasis on the arguments for allochthony and autochthony. Various aspects of the nature, growth, and decay of the characteristic vegetation of the brown coal peat moors, their conversion into coal, the origin of banding, and the influence of tectonics are discussed.A description of the banding in Victorian brown coals is followed by a discussion of their vitrain, fusain, and natural carbonized coal; and concludes with the nature of the coal resin and the possibilities of its extraction.The nature and derivation of inorganic matter in brown coal, based on Lessing's classification, is described. Assimilation of mineral substances in specific plants with variations due to environmental factorsare illustrated by analyses of present day trees. Consideration is then given to possible sources of salt, marcasite, and quartz in brown coal.It is shown that part of the inherent and extraneous ash may have been removed during and after coal formation. The nature and abundance of the organically combined substances in brown coal emphasizes the anomalies that may arise from estimating the total inorganic matter from ash contents.After classifying deposits on external heating surfaces of boilers, theoretical and practical aspects of slag formation, alkali matrix deposits, and the effect of sulphur and chlorine are considered.Analyses of deposits in boilers burning Victorian brown coal are tabulated.Slagging at the Yallourn power station from sand in the Yallourn open cut, and difficulties with Yallourn North Extension coal at the Maryvale paper mills are described.Tests carried out on Morwell and Yallourn coals showed that with the former, impacted deposits formed on boiler heating surfaces, and left a high percentage of chlorides on probes. Morwell briquettescompared with Yallourn briquettes also reduced the running time of a semi-industrial boiler through deposits with sodium sulphate as...

Jan 1, 1962

The mostly submerged New Zealand sub-continent has a complex geological history and an active oceanographic regime that provides opportunities and challenges for offshore mineral exploration. Known deposits include polymetallic Fe-Mn nodules and crusts, polymetallic massive sulfides, phosphatic nodules, titanomagnetitie ironsands and placer gold deposits. Currently exploration interest is high with some 3.5 per cent of the EEZ under prospecting permit or application.   Article 76 of the UNCLOS convention allows coastal states to have sovereign rights over areas of the seafloor that are natural prolongations of the landmass that constitute submerged parts of the continental margin as extended continental shelf. New Zealand has substantial areas of elevated ridges and plateaux beyond the 200 M EEZ that form extended continental shelf. New Zealand has nearly completed a ten year, $44.4 M programme to define its outer extended continental shelf. New Zealand will lodge its outer limits of the extended continental shelf with the UN-appointed Commission on the Limits of the Continental Shelf in 2006, which if accepted, will enclose ~1.8 million km2 beyond the existing EEZ. Ocean Survey 20/20 is a follow-on marine mapping programme to underpin resource exploration and environmental management of the EEZ and extended continental shelf.

Jan 1, 2005

Bauxite Resources Limited is grade drilling in its Western Australian Darling Range tenements to firm up resource definition and to develop mine plans. The Darling Range bauxite is generally in shallow deposits with minimum overburden. In the northern tenements, the ore is characterised by a higher silica layer which may extend from 0.5 to 1.5 m below, which high grade bauxite is found to a depth of four to 7 m. When grade drilling samples are taken, every 0.5 m and the recovered sample is weighed, logged and bagged. To eliminate splitting errors, the whole sample over the short interval is pulverised. Twinning holes variations are observed when using various drill rigs. Diamond core has been shown to give close to 100 per cent recovery and grades have been verified by digging bulk samples. As such, diamond core is used as the reference. It is intended to include sonic drilling as an alternative to diamond cores. This presentation details and attempts to explain the reasons for the observed variations in the various drilling methods used by Bauxite Resources Limited. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010

By H Simpson, C Gimber

The financial evaluation of mining projects drives a whole range of decision-making regarding project viability, project design, operating models and closure philosophy. Net Present Value is a financial assessment approach that is pervasive across the industry and has been widely criticised for driving short-term thinking and leading to poor long-term outcomes and future unfunded closure liabilities. But are there alternative models and what are the impediments to their implementation? This paper aims to outline current and past mine closure practices in the mining industry and questions these outcomes given the changing shareholder investment requirement for alignment with sustainable Environmental, Social and Governance (ESG) goals. Examples are presented of closure programs planned and executed in the later stage of the life-of-mine and explores the benefits that could have been realised by integrating these into concurrent production operations. Examples of simultaneous mine development and closure execution and their benefits are presented, and their relevance to corporate investor branding. This paper also discusses the concept of investor project ownership through to sustainable closure and outlines alternative approaches to responsible, sustainable mine closure. We explore the current mining industry divestment practices to remove closure liability from the balance sheet. These underlying financial practices and Net Present Value approach to Mine Closure and alternative approaches are discussed.

Aug 2, 2023

The mill area of PT Freeport Indonesia is located in a valley surrounded by steep natural slope, characterised by extreme topography with mountains rising to above 4500 m within 100 km from the seashore. The valleys are deeply embedded into the mountainous terrain and bordered by steep natural slopes. Vertical or overhanging lime walls are interrupted by steep vegetated screen sections containing accumulated loose material from weathering processes and ancient rock falls and/or debris flows/avalanches. The climate can be best described as alpine subtropical with an accumulated rainfall of more than 5000 mm per year. Occasional snowfalls and superficial freezing above 4000 m elevation leads to heavy weathering of the superficial rock layers and along open joints and fractures. The mill area is a crucial and strategic infrastructure for the entire mining operation which is best characterised as a high density industrial area with facilities including water tanks, power generators, crusher, and concentrating facilities including office buildings and workshops as well as access tracks to the underground mining blocks. Considering the local topography, the restricted space conditions and the number of technical installations, the facilities are likely to be affected and highly vulnerable to rock fall from the surrounding slopes. In order to minimise the rock fall hazard three rock fence barriers area were constructed at the mill area. The 7.5 rock fence barriers were designed with the maximum capacity of 5000 kJ. These are the largest capacity of rock fall barriers ever constructed in Indonesia. The total length of the barriers for the three locations was 126 m. The biggest challenge of this project was the construction of the barrier at West Gulley, which was constructed at 300 m above ground level. For this site, construction access was undertaken using helicopter. This presentation discusses the design of the mitigation structures as well as the construction approach and stages of the barriers. Please note: This paper is abstract only.

Nov 25, 2010

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By K Sommerville

BHP Billiton’s Area C iron ore operation has been in production since 2003. During 2010, below water table mining in the Marra Mamba formation commenced and dewatered ore has been successfully processed through the plant.The ability to mine below water table material increases reserves. Pits can be dewatered using a combination of ex-pit and in-pit bores. Critically it is important to allow suffi cient lead time to dewater. For Area C, in-pit bores yield the most water which presents challenges in every day operations when mining around bores. Operationally there are steep learning curves in obtaining equipment, training personnel and setting up infrastructure. Core risks include lifting, refuelling and maintaining gensets. The pipework, extraction and re-establishment work can be very manual.The challenges include blasting, mining, stockpiling, processing, water balance and disposal. Maximising up time on bores whilst minimising impacts to blast practices have evolved. Blast practices now align bores to the edge of patterns. Protecting bores have evolved from stemming bores with rock and re-drilling to using gas bags which require no drills. Based on moisture and material properties, mining of dewatered material can be categorised into three groups:1. normal,2. sheeting, and3. sheeting and top loading.Ore can go straight to the plant ore to drying pads where it takes between one and three months to drain.Stock management of these piles is important to ensure efficiency of the plant. Rules have been established for blending wet material to maintain feed capacity and some modifications to plants have been made. Dewatering of pits poses a challenge for water use. Initially turkey’s nests were established to capture water and use for dust suppression. As water abstraction has increased methods of management include using exhausted pits for storage and evaporators. Managed Aquifer recharge and use in potable water are being considered. An over arching coordination of the capacity and use are required.Important elements in dewatering include:• capacity models,• capital,• long to short planning,• day to day coordination, and • water level monitoring and balances. Success in dewatering requires a cross function team working towards a common goal. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011