Search Documents

Jan 1, 1969

By R. A. Harrington

THE structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in elec-trolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under dif-ferent sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc, The electron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (10-6 cm.). Different investigations of the structure of anodic films have shown widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's' X-ray diffraction patterns of eloxal? films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3-§ Burgers, Claassen, and Zernicke3 obtained sharp X-ray

Jan 1, 1940

By U. N. Bhrany, J. H. Brown

The specifications of particle size and the size analyses of fine particulate materials are commonly presented without reference to the method of analysis. A review of the various sizing methods showed that not only numerous sources of error but also different definitions of size are inherent in the different methods of analysis. To demonstrate the magnitude of the differences, the size distribution of finely crushed quartz was determined by several methods and a critical comparison of the data was made. The experimental results show that appreciably different sizes may be indicated for one material depending on the method of analysis used. However, because the shape of the size-distribution curves determined by almost all methods was constant, a simple method of correlating the data can be adopted. Conversion factors, by which size measurements obtained by the various methods can be expressed in terms of screen sizes, are presented as one method of correlating the results. The size analysis and size specification for lump rock and particulate materials are commonly determined with sieves. With this technique, a readily reproducible measure of size can be obtained merely by duplicating the sieve and the method of sizing. For coarse materials, such as lumps of rock, this technique is simple and effective; and the effects of properties of the material such as shape can be readily understood. When very small particles are measured, however, problems arise. Small sieves are difficult to construct and maintain, and size separations become sensitive to the analytical procedure. For these difficult sieve sizes and for still smaller particles, other sizing techniques employing, for example, sedimentation, light extinction, and microscopy are available. Because these various techniques employ different size-dependent responses to establish size, it is appropriate to examine them and the results they yield to determine their relationships and their limitations. The 'size' of a lump of rock is not an absolute quantity, but rather a defined one. With sieves, for example, the size is defined by the screen aperture and no reference is made to the actual shape of the particle, yet only in the case of a regular body, such as a sphere, can the sieve size be related to the shape. With sieves only two dimensions of a particle can be suggested, for the sieve makes no allowance for the length of the particle passing through an aperture. Similarly, the size of a particle as measured by a microscopic technique need bear no relationship to the size as measured by sieves, although the two measurements may be related statistically. In fact, all size measurements are not only defined quantities, but the measurement actually used is an average that is controlled by the technique employed and, hopefully, reflects the property in question of the material of interest. Many papers have been presented that illustrate the accuracy of the various sizing methods, present the advantages of certain methods for certain applications, and describe the principles and technical backgrounds of the various methods. No attempt will be made in the present paper to review this work in detail. The purpose of the present paper is to examine the limitations of the various sizing methods, and to demonstrate experimentally the relationships between the sizes as determined by the various methods of analysis. It is hoped that by recognition of these limitations and relationships, errors in size specification and size interpretation will be avoided. REVIEW OF SIZING METHODS In specifying the size of a material, not only the data but also the method of measurement must be stated. For example, the size of the lump might be specified as its total volume, as its weight, as its maximum dimension, or as its minimum cross section; any one definition might be completely satisfactory for one problem, but not for another. In practice, size analyses follow four basic approaches and fortunately, the conditions that restrict each approach are known. These major methods include: 1) screen analysis, 2) direct measurement of particle dimensions, 3) determination of equivalent spherical size in response to fluid flow, and 4) specific surface determination. Each of these techniques has several variations and some new techniques are also available, but the limitations of the basic techniques are sufficient to permit at least a preliminary

Jan 1, 1962

By L. C. Graton

THE Federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of Federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal indus-tries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Be-cause of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final

Jan 11, 1919

By L. E. Young

THE progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. INTRODUCTORY STATEMENT AND SIGNIFICANT POINTS IN PROGRESS Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: I. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods and the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, considering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for the mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics, petroleum engineering, petroleum technology, ceramics and so forth. 7. There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1947

By Earl S. Greiner, Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two monographs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken. Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon. Discussion oF Continuous Series It has often been said in print that the iron-silicon alloys form a continuous series of solid solutions from 0 to 15 per cent. silicon. This claim the authors are inclined to doubt: first, because the alloys from 0 to 4.25 per cent. silicon are ductile and malleable at atmospheric temperature, while those with 5 per cent. or more of silicon are comparatively hard and brittle. Furthermore, the alloys with more than 4.25 per cent. silicon are comparatively hard and low in ductility at atmospheric temperature, but become much more ductile when heated slightly. It is well known, for example, that the alloy containing 4.75

Jan 1, 1930

By Will H. Coghill, P. H. Delano, G. D. Coe

DATA concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as "grindability-index numbers," but grindability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pulverized product by a method comparable with commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulverizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation, it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-3/4 -inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horse-powerhours." The channel-roller pulverizer here-inafter described is believed to meet these requirements. HISTORY OF THE MACHINE The work started when Ralph W. Smith, engineer, St. Genevieve Lime Co., St. Genevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasiveness of dentifrices,1 and it was thought the same principles might be applied to coal. Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By P. K. Koh

Isothermal salt bath annealing of 0.014-in. thick 3 pct Si-Fe sheet was conducted at temperatures ranging from 927" to 1260°C in order to investigate the grain-growth behavior. Within the temperature range studied normal grain growth did not take place; instead nucleated grain growth prevailed. The nucleation frequency was found to increase with the annealing temperature, with corresponding decrease in grain diameter of ultimate secondaries after long-time annealing. Large secondaries grown by low-temperature isothermal annealing are essentially of (110)[001] orientation, and the (110)[001] texture is strong. The relatively small secondaries grown by high-temperature isothermal annealing also have orientations near (110)[001] as an average but widely scattered; thus the amount of (110)[001] texture is found to decxease with isothermal annealing temperature. Grain growth and texture development at various annealing temperatures can be described by families of sigmoidal curves with the time axis. ThE cube-on-edge (110)[001] texture and predominating large secondaries in fully annealed 3 pct Si-Fe are customarily produced by a 1100°C annealing of a primary recrystallized sheet. On annealing the primary recrystallized sheet above the temperature at which secondary recrystalliza-tion starts May and turnbull' have demonstrated that secondary grains decrease in size as the temperature is increased. The phenomenon was attributed to a decrease in the (G/N) ratio where G is the growth rate of secondary grains and N is their nucleation frequency. In addition, the growth of grains in orientations rather far from (110) [0011 occurred. The present investigation is devoted to detailed rate studies of the same phenomenon. Mi-crostructure, magnetic anisotropy, and texture data were obtained on strips of 3 pct Si-Fe isothermally annealed for various lengths of time in a BaC12 salt bath at temperatures ranging from 927' to 1260°C. The texture results are reported elsewhere.2 EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon-iron strip (3.16 pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Metallo- graphic studies indicated complete recrystallization. In order to provide a protective atmosphere and to obtain a rapid rise to an elevated temperature, a BaC12 and NaCl fused salt bath was used to heat samples isothermally at temperatures from 927" to 1260°C for various lengths of time. Torque magnetometer measurements were made on 1-in.-diam disc specimens before and after annealing, since magnetic torque curves supply information on textures and texture changes. Surface layers of the strip samples were polished and etched to reveal the grain structure. The diameters of grains were measured from micrographs at X100. The average value of diameters of matrix grains was established. Individual grains in the micrograph were cut out separately along grain boundaries. These grains were classified either as matrix grains or growth grains. The percent weight of growth grains in the cut-out patterns was reported as percent growth. Manv of the individual grains in the annealed samples were large enough to be X-rayed with a 5-mil beam for Lauegrams. Complete (110) pole figures were obtained for the primary recrystallized structure and short-time annealed structure with CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and ~ruce.~ Both the X-ray optics and the technique for pole figure differed slightly from those adapted previously.4

Jan 1, 1960

By Robert Maes, Robert de Strycker

The Cu-Sn-As systeM was studied in the region near the Cu-42 and (214-As binary diagrams, where reactions in the solid state appear, resulting from the decomposition of the y(Cu-Sn) phase and from the formation of the 7 phase (Cu,As). The techniques used were microscopic observation, thermal analysis by dilatometry, and X-vay diffraction. The formation of the 7 phase gives rise to a ternavy pevitectoid veaction; the decomposition of the y phase gives rise to five transitional reactions. The temperatures of almost all these reactions could be determined; in the most favorable cases , the accuracy of this determination was of 11.5-C. The 7 phase is stabilized by tin additions, the arsenic atoms being replaced by tin atoms up to 35 pct; this has allowed the preparation of pure j) phase and the confirmation, by extrapolation, of the conrposition of this compound in the Cu-As diagram. In the first part of this work, the solidification reactions in the Cu-Sn-As phase diagram were studied. In the copper corner, the structure of the alloys presented the evidence of reactions in the solid state: on the one hand, all the alloys containing the y phase of the Cu-Sn diagram showed, under the microscope, that this phase had formed different decomposition products after complete solidification; on the other hand, the appearance of the 7 phase of the Cu-As diagram necessitated the introduction of a peritectoid formation reaction. The study of the decomposition of the y phase has been done by preparing about forty alloys that were homogeneous y at high temperature. The formation of the 7 phase has been studied by means of a few alloys with a composition near the homogeneity field of this phase at room temperature. The part of the Cu-Sn phase diagram of interest for this study is represented by Fig. 1, with the phase designation which will be used in the remainder of this paper; it is drawn after Hansen and Anderko.' The Cu-As diagram has already been presented in Part I of this work; the significant features of this study are the existence of the arsenides CusAs and Cu5Asz, and the formation of a compound CUEAS, designated as the 7 phase, by a peritectoid reaction at about 325°C. EXPERIMENTAL METHODS The fundamental technique for the investigation of this part of the Cu-Sn-As constitution diagram was microscopic observation; the greatest part of the observed alloys has also been subjected to thermal analysis by dilatometry; a few selected alloys have then undergone an X-ray analysis by powder diffraction. Alloy Preparation. The alloys were prepared from the same products as in Part I of this study: cathode copper, arsenic with a purity better than 99.5, and tin with a purity of 99.98. The fusion of the ternary alloys was realized from

Jan 1, 1967

By Henry J. Miller, Marcella Linderman

During some experiments made by Henry J. Miller, partly in Germany and partly in the United States, in which it was found necessary to melt metals in quantities up to 60 kg. in a vacuum or under low pressures of hydrogen, molybdenum was tried as the resistor in the electric melting furnaces. Molybdenum ribbons 16 by 0.55 mm. and 18 by 0.45 mm. were used as resistors. The furnaces were of the type shown in Fig. 1. About the heating tube, Y, are wound parallel resistors of molybdenum ribbon from the water-cooled electrodes, El, Ez. The whole is within a copper container having outlets for the removal or introduction of gases and a window, W, for observation, the space about the heating tube and electrodes being filled with insulating material. The life of the molybdenum used as the resistor was found to depend very much on the manner of using it, its failure being due in some cases to thinning by evaporation or chemical reaction and in others to hardening, which prevented it from following the expansions and shrinking of the heating tubing without cracking. As such failures are often rather expensive in commercial work, it was thought worth while to determine the causes. The factors influencing the behavior of molybdenum resistors used in this manner may be briefly stated as follows:

By R. F. Sheldon

The discovery of the Carlin deposit was the result of discriminating geologic research and prospecting devoted to the objective of finding a gold deposit that could be mined by open pit methods. By the late 1950s, Newmont Mining Corp. was becoming increasingly concerned about the trend of rapidly rising underground mining costs unless bulk mining methods could be applied. The desirability of finding an open-pittable gold deposit was apparent. The attention of Newmont geologists was directed to Nevada by the publication of two papers: "Paleozoic rocks in North-central Nevada" (1958) and "Alinements of Mining Districts in North-central Nevada" (1960), both authored or co-authored by Ralph J. Roberts of the United States Geological Survey. John Livermore, geologist of Newmont Exploration Ltd., attended a talk given by Roberts in Ely, Nevada in the summer of 1961. These papers and the address by Roberts gave details concerning the Roberts Mountain overthrust, a 483 km (300-mile) long, shallowdipping fault which pushed clastic and volcanic rocks of early and middle Paleozoic age eastward over younger marine formations. Subsequent uplift and doming with consequent erosion had locally removed the upper plate strata exposing windows of lower plate carbonate rocks. Roberts noted that the principal mineral deposits of the region, including gold, were associated with these windows which exhibited a preferred alinement. In the summer and fall of 1961 Newmont's exploration geologists John Livermore and J. Alan Coope began a systematic examination of gold occurrences associated with these windows, aided by further discussion with geologists of the US Geological Survey. Attention was directed to the Lynn and Carlin windows, particularly to those formations lying immediately above and below the Roberts Mountain fault. It was appreciated at the time that many of the gold occurrences in the region were unusual in that no colours were obtained even when panning high grade samples. A large number of rock samples were collected and analysed using fire assaying procedures, and background values for gold were established. This systematic rock sampling resulted in the identification of a distinct area of anomalous gold values, and a block of claims was staked in late October, 1961. These claims, plus an adjoining optioned 32.4 ha (80 acres) of ground, cover the main area of the present Carlin gold mine. Prior to snowfall that winter, one of the bulldozed assessment pits required to establish a claim's discovery exposed 24 m (80 ft) of mineralization assaying 0.007 kg/t (0.22 oz per st) gold. In the spring of 1962 a program of trenching, sampling, and geological mapping followed by rotary drilling was underway. Other properties in the area were acquired. The generally undistinguished nature of the dolomitic siltstones and silty dolomitic limestones hosting the micron-sized gold particles, coupled with the lack of visually associated guide minerals, made identification of the gold bearing areas very difficult. The entire drill column had to be assayed to ensure that values were not overlooked, as very often sections that might be assumed to be waste turned out to be high grade. On September 10, 1962 a high grade intersection of 24 m (80 ft) assaying over 0.03 kg/t (1 oz per st) gold was encountered in the third hole drilled. An expanded program of both rotary and diamond drilling led to the further delineation of the ore body. By December 1963, the exploration program had established an initial reserve of 10 Mt (11 million st) grading 0.01 kg/t (0.32 oz per st) gold. A 1.8 kt/d (2,000 stpd) processing plant was constructed and the first gold bullion was poured in May, 1965, just two years and eight months after the discovery hole was drilled. REFERENCES Roberts, R.J., Holz, P.E., Gilluly, J., and Ferguson, H.G., 1958, "Paleozoic Rocks in North-central Nevada," Bulletin American Association of Petroleum Geologists, Vol. 42, No. 12. Roberts, R.J., 1960, "Alinements of Mining Districts in North-central Nevada," Professional Paper 400-B, US Geological Survey, Article 9.

Jan 1, 1985

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By AIME AIME

COMMITTEE No. 2 of the Iron and Steel Institute b f Great. Britain has presented its first report, of 27 printed pages, on blast-furnace plant and practice. This report outlines the various features of modern blast-furnace practice with brief comments thereon, and with references to some of the more recent methods devised for applying the principles and attaining the purposes aimed at' under these headings.. In general, the trend in the United States is in the direction of larger and larger furnaces with ever increasing capacity from which, with improved details in methods and equipment, and attention to details of management, considerable progress in. economy of production has been attained, in fuel consumption and in other items of production cost.

Jan 1, 1929

By G. E. Goodspeed

The Cornucopia gold quartz veins form a parallel vein system traversing meta-morphic and granodioritic rocks. Field and petrographic evidence suggests that inetasomatism has played an important role both in the emplacement of the grano-diorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore-forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a shght amount of cross faulting, and some movement along the planes of the veins as well as oxidation. Introduction Cornucopia is in the southeastern part of the rugged Wallowa Mountains of northeastern Oregon. It was founded over 50 years ago following the discovery of its system of gold quartz veins. The major veins are roughly parallel and dip into the western side of Pine Valley, which drains the southern slope of the range. Previous operations had cut the upper portion of four major veins with two tunnels over 1000 ft. apart, when the present operating company drove a third tunnel, called the Coulter, at the level of the valley over 1000 ft. lower to intersect the most easterly major vein at over 6200 ft. from the portal. General Geology of District The oldest rocks in the vicinity are metamorphosed sediments and volcanics. These, for the most part, are presumably Mesozoic in age, although some black argillites outcropping along East Pine Creek are considered to be Permian.l,2 These rocks have been deformed and metamorphosed in general to hornfels at the close of the Jurassic. The series was then invaded by a granodiorite batholith, the origin of which is

Jan 1, 1941

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent suficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involvetd the purchase of several hundred tons of halls of a specific type which were then run in one or more ball mills for a period ranging from several months' to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1'2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By John Hall

(New York Meeting, October, 1913.) THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 11/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or. chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions.

Jan 7, 1913