Search Documents

By T. L. Joseph

IN connection with its investigations of the blast'-furnace process, the Bureau of Mines, in coöperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferromanganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new, raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the coöperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests.

Jan 1, 1928

By Robert Pring

IN addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of em-ployees, with a consequent decrease in labor turnover rates. One progressive mining company estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination de-creases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor. Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flow-sheet. Exhaust ventilating systems are now afforded equal care in design and mainte-nance to that given other machinery more closely related to the process,

Jan 1, 1940

By J. F. Sepulveda, J. D. Miller

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 9, 1978

By E. S. Grumell

THE correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbrevia-tions will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution.

Jan 1, 1939

By W. E. Pugh

The object of the following is to discuss a few of the problems encountered in the practical field application of reflection seismology. Very little has been published on this phase of the work and it is to be hoped that discussions will be presented by many seismologists who have met with these problems in the field. No attempt will be made to discuss the general principles of reflection prospecting, nor to outline the general field procedure. These phases have been presented more or less in detail in previous publications1 while economy of space and time prevents their being repeated or amended here. If, in the following pages, some criticism is offered of those who have already given their time and efforts to present valuable papers on reflection shooting, we trust that it will be accepted in the constructive light under which it is offered. We do not wish to give the impression that the following paragraphs represent ultimate achievement in field procedure; they are presented more to illustrate methods we have found satisfactory thus far. We believe that the following three subjects are inexorably linked with the continued future successes and more widespread use of the reflection method which, at the present time, is the most

Jan 1, 1934

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

By A. J. Jacobs, J. W. Spretnak, R. Speiser

The activities of nickel in liquid iron-nickel solutions containing from 10 to 90 at. pct Ni were measured over the temperature range .1510° to 1600°C. A special function was devised whereby activities can be computed by a graphical integration using the results of chemical analyses on the vapor phase alone. The liquid solutions studied exhibit negative deviation from Raoult's law, but they approach ideality as the temperature is raised from 1510° to 1600°C. The maximum heat of solution is less than -8.0 kcal per mole. The entropy of solution is less than —2.5 kcal per mole deg at 1510°C, and changes negligibly as the temperature is raised. The liquid iron-nickel solutions do not follow regular solution behavior. THE activities of the components of a liquid alloy system can be determined in favorable cases from the partial pressure of the vapor in equilibrium with the liquid alloy.' Assuming that the vapor over the alloy behaves as an ideal gas, the activity of component i is given by the expression, Where the superscripts 1, v, and o signify the liquid, the vapor, and the pure component, respectively; the f's are the fugacities, and the P's, the pressures. The quantities Pi and Pi can be determined by the

Jan 1, 1960

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By G. A. Deitz, J. Halpren

The kinetics of dissolution of silver in cyanide solutions under oxygen pressure have been investigated over a wide range of conditions with a view to establishing the reactions involved and the factors which influence the rate. The results indicate that the rate is determined principally by the transport of reactants in solution to the silver surface. The thermodynamic features of the reaction with particular reference to the influence of pH and CN- are also discussed and summarized in the form of potential-pH diagrams. METALLIC silver is readily attacked and dissolved by cyanide solutions in the presence of oxygen. This reaction has long been recognized and extensively applied1 in the well-known cyanide process for the extraction of silver from its ores. While this process has been subjected in the past to a number of investigations2,3 both of a practical and fundamental nature, some features relating to the chemistry of the reactions involved, the role of oxygen, the nature of the rate-controlling step, and the effects of pH and certain reagents such as lime, are still not fully understood. It was felt that this situation justified a further investigation of the reaction, made with a view to obtaining a better understanding of its kinetics and mechanism. In the present investigation rate curves for the dissolution of silver were determined over an extensive range of carefully controlled reaction conditions. By carrying out the reactions in a pressure vessel, the partial pressure of oxygen, and hence its concentration, could be varied widely. The influence on the reaction of other variables including temperature, pH, and the concentrations of cyanide, peroxide, and other salts was also examined. The results of these kinetic studies are presented and discussed in this paper, together with a summary of available thermodynamic information relating to the possible reactions which can accompany the attack on silver by aqueous solutions of cyanide and oxygen. Chemistry and Thermodynamics of the Reaction The chemistry of the reactions of gold and silver with aqueous cyanide solutions has been the subject of several recent reviews.'." It has been proposed' that the following reaction occurs when silver dissolves in cyanide solutions in the presence of oxygen: 4Ag + 8CN- + 0, + 2H.0 -t 4Ag(CN); + 40H- [la] An equation of this form, for the corresponding dissolution of gold, was first suggested by Elsner." Bodlaender5 proposed a similar overall reaction, but suggested that it took place in two steps, 2Ag + 4CN- + O2 + 2H2O ? 2Ag(CN),- + 2OH- + H2O2 [2a] followed by 2Ag + 4CN- + H2O2? 2Ag(CN); + 20H- [3a] On the other hand, Janin- suggested that the dissolution of gold can occur with the liberation of hydrogen, rather than by reduction of oxygen. The corresponding equation for the dissolution of silver is 2Ag + 4CN- + 2H20 -t 2Ag(CN); + 20H + H2 [4a] All these reactions represent oxidation-reduction processes and may be resolved into the corresponding separate oxidation and reduction components. The oxidation step involves the formation of the argentocyanide ion and is the same for all the reactions, i.e., Ag + 2CN? Ag(CN)2 + e [51 However, reactions la, 2a, 3a, and 4a differ in the nature of the reduction steps which are, respectively, O2 + 2H2O + 4e ? 4OH- [lb] O2 + 2H2O + 2e ? H2O2 + 2OH- [2b] H2O2 + 2e ? 2OH- [3b] 2H2O + 2e? 20H- + H2 [4b]

Jan 1, 1954

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By John G. Hall

The pumping operations at the Chief mine have been unique in the respect that for many years the entire flow of water into the mine has been disposed of by pumping into natural underground "caverns" or "sinks." Volumes up to 4000 gpm have been pumped into these caverns with no apparent tendency for the caverns to fill with water, and it has never been proven that any of the water returns to the mine workings. Major pumping operations have been carried on during two periods, the first from 1918 to 1927, and the second from 1942 to the present time. Early Pumping Operations CHIEF MINE The Chief Consolidated Mining Co. was organized in 1909, and for the following nine years ore was developed and mined from the 600 level down to the 1800 level, all above the permanent water table, the 1820 level. The ore occurs as extremely-irregular pipes of replacement ore in limestone, and to date a total of approximately 2 1/2 million tons of ore has been produced. The ore was highly oxidized down to the permanent water level, and some highly-oxidized ore runs occur beneath the permanent water table. In 1916, with extensive mining being done on the 1800 level, 20 ft above the water table, there were indications that a zone of secondary enrichment might exist below the water, and in order to follow the ore runs to greater depth, it was realized that arrangements would have to be Made to pump water to the surface. The original pumping installation was designed to pump 350 gpm in five stages against a 1900-ft head to the surface. By January 1919, the water had been lowered to the 1900 level and an excellent grade of silver-lead ore was being produced from the zone of secondary enrichment. At this point. the flow of water equalled the capacity of the pumps, and pumps of an additional 1000 gpln were installed to supplement the original system. By January 1920, the water had been lowered approximately 100 ft, and the total flow of water was 1000 gpm. The water was being pumped from many different places in the mine where ore was being followed downward, with 27 different pumps operating below the 1800 level, mainly Cameron air-driven sinker pumps. These first sinking pumps were cumbersome and inefficient, and each of the larger pumps weighed approximately three tons and required tremeridous volumes of compressed air. During this period, an exploration drift being extended north and west from the Chief shaft on the 1600 level encountered a large natural cavern some 2000 ft from the shaft. This cavern in places measured 60 ft in diameter. Sometime later the disposing of water into this cavern was suggested, and as an experiment to determine the results of such an operation, an attempt was Made to fill the cavern by pumping in a small volume of water, but the water disappeared as fast as it was discharged into the cavern. It was decided then to try the cavern as a drainage outlet for the entire volume of water being pumped to the surface, and the water apparently did not return to the mine workings. Subsequently water up to 3000 gpm was pumped into this cavern. An attempt was made to determine whether any water was being returned from the cavern to the lower workings, and 100 lb of sodium fluorescein salt was added to the water discharged into the cavern, but no trace of it was found in the drainage water in the mine. Results of another such test will be described later.

Jan 1, 1950

By W. C. Lilliendahl, G. Meister

Uranium metal with a purity of about 99.9 pct was produced on a large scale by fused salt electrolysis with a material efficiency of about 90 pct. The material efficiency depends mainly on bath composition, electrolysis temperature, electrode smothering, and elutriation during washing of the powder. RESEARCH and development work on fused salt electrolysis carried on by the Westinghouse Lamp Div. Bloomfield, N. J., was done under the Manhattan District Corps of Engineers and later under the Atomic Energy Commission for the commercialization of uranium production for the first atomic pile at the University of Chicago in 1942. From the conception of the atomic bomb project it was recognized that metals with impurity levels having little metallurgical significance would be required. Permissible impurity levels were based on neutron absorption. Of particular significance was boron, which could not be present in amounts exceeding 1 ppm. The electrolytic method as developed in 1930 by Driggs and Lilliendahl,1,2 and later improved, yielded uranium of very low boron and other deleterious impurity content. No other method was capable at that time of producing uranium metal of the required purity.' The low boron content of uranium produced by the electrolytic process resulted from the availability of the reactants which were low in boron content, and from the inherent elimination of boron in the fused salt bath. Since the heart of any electrolytic process is the electrolysis cell, this paper will deal with the development of the original bath composition for the efficient production of uranium from a batch process to one of continuous operation. Emphasis also will be placed on other factors which will affect the material efficiency of the process. With the laboratory cell the material efficiency of uranium powder recovery in the early electrolysis was relatively low, about 35 pct based on the ratio of uranium recovered to uranium added. This early process also had other defects. The electro- lytic bath could not be used continuously. After three runs from a freshly charged crucible, the deposit showed a tendency to slip off the electrode as it was raised from the bath. This condition necessitated pouring the charge every fourth run and preparing a new bath. It was assumed at that time that this condition was caused by the increasing fluoride concentration with each addition of uranium salt, which adected the mobility of the uranium ions. Experimental The electrolysis cells differed in size only. They were of the floating cathode type. The laboratory cells were 21/2 in. ID and 6 in. deep and operated at 30 amp and 5 volts. Production was about 150 g metal powder per 8 hr. The plant cells (5 units) were 9 in. ID x 21 in. deep and operated at 1800 amp at 12 volts. The total production unit was designed to produce 250 lb of uranium powder per 8 hr day. Because of the tendency of uranium fines toward spontaneous combustion, material efficiencies were based only on the recovery of useful coarser metal which could be safely handled. The reported efficiencies are of particular significance only as related to the same group of experimental procedures. At the start of the project no changes were contemplated until previous data could be definitely confirmed. Therefore, the first experiments were with the 50 pct CaCl2-50 pct NaCl mixture. The material efficiency of uranium deposition as a function of the number of electrolyses is shown in Table I. In Table I, the decrease in efficiency at 800°C with number of runs is apparent and confirmed the earlier data. Operating at 900°C enabled the number of runs to be doubled, but before pouring the charge the efficiency of recovery became poor. This test indicated that the improved efficiency might have been caused by an increase in the fluidity of the bath.

Jan 1, 1958

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By Herbert W. Huse

Nitrogen, and its compounds, unique among the materials described in this volume, is absolutely essential to the existence of the human race. Almost all minerals are important and the absence of any one of them would be sorely felt; but nitrogen is an integral part of the cycle of life itself. Man cannot live without nitrogen which, as an inert gas, composes the major part of the air he breathes; as compounds, nourishes the vegetation which he eats; and, as protein, forms a part of his very flesh and blood. Nature originally provided man with a vast reserve of usable nitrogen compounds in the form of fertile soil. She constantly replenishes the supply by "fixing" nitrogen in the air at the estimated rate of 400,000,000 tons per year (an insignificant 6 lb per acre) during electrical storms. She has also placed certain microorganisms in the soil which are able to "fix" nitrogen and convert it into forms which plants can use. Legumes like cow peas, soy beans, clover, and alfalfa have extraordinary roots which serve as stimulating hosts to these bacteria which, in turn, nourish the plant. By plowing in all or part of such crops, their above-average nitrogen content can be returned to the soil for other more useful crops. The mechanism for this recycle is supplied by "denitrifying" bacteria which attack the dead plant tissue and liberate nitrogen and ammonia. However, since one crop of grain, sugar beets, potatoes, tomatoes, etc., takes out a major portion of the nitrogen which a plowed-in legume crop can supply, this method of fertilization is obviously inadequate. Drastic intervention by man has become necessary to support the ever-growing population of the world.9,15,20 Old civilizations with a high population density, such as the Chinese, were able to exist for centuries by carefully tilling the soil, rotating crops, and returning to the soil all the nitrogen in vegetable wastes plus human and animal excreta. But the lack of a means for augmenting their supply of nitrogen placed a ceiling on further development and kept the mass of the population in a chronic state of undernourishment, frequently punctuated by famine. Nitrogen plays another important role in the life of mankind. In the form of explosives, nitrogen helps to wrest from the earth many materials needed for our material well-being. Also, in the form of explosives and propellants, nitrogen increased the destructiveness of wars to a point only exceeded by the fantastic power of atomic energy. Man's first really effective efforts to improve his position with respect to nitrogen began in the 18th Century with the mining of sodium nitrate. By the late 1880's this had become a big industry serving a large part of the world. In the late 1890's nitrogen, in the form of ammonia, was being recovered from coke-oven operations. In 1900 nitrogen, in the form of nitric oxide, was being obtained from the air by an electric-arc process. About 1904 another "fixation" process based on the reaction of nitrogen with calcium carbide to form cyanamide was commercialized. By 1913 the Haber-Bosch process of "fixing" atmospheric nitrogen by reacting it with hydrogen to produce synthetic ammonia was successfully applied on a large scale, first in Germany and then throughout the industrial areas of the world.9 All the above methods of obtaining nitrogen compounds are still in use and, between them, they assure mankind of adequate supplies for all time. While this fortunate situation is not unique amongst industrial raw materials, all too few of man's needs are so well in hand.

Jan 1, 1960

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By Robert M. Lewis

Can wet-ground mica be produced from mica schist ores, and if so, would its properties be comparable with products now on the market? This was the problem which prompted the development of a flowsheet for the beneficiation of mica schist. The fine-ground mica industry relies on weathered pegmatites and alaskite ores as sources of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and bulk-density specifications. Mica obtained from mica schist is iron-stained and decrepitated and requires additional beneficiation to produce a wet-ground mica product. Despite these adversities, there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores is considerably higher than that of the pegmatites and alaskite ores now being mined, often containing in excess of 40% mica. This higher-grade mica feed should promote a lower mining and milling cost. The mica schist ores with their higher mica content would mean less tailings to handle; however, there would have to be a means for disposing of acid and sulfate wastes. A flowsheet was developed whereby mica could be recovered from mica schist ores and beneficiated in a way that would result in a high-quality end product.' The essential phase of the process involves using reducing reagents to increase the magnetic susceptibility of iron contaminants which then can be removed with a magnetic separator. General Treatment Procedure The mica is floated by either of two methods, an amine float in an acid circuit' or the U.S. Bureau of Mines (USBM) amine-fatty acid float in an alkaline circuit' The flotation mica is ground in a pebble mill to liberate contaminated particles and expose iron-stained surfaces. The concentrate is then conditioned with a reducing reagent and passed through a Frantz Ferrofilter for the removal of magnetic material. The nonmagnetic product is acid-leached to further reduce the iron contamination. The leached material is then ground to product size and checked for specifications. Discussion of Flowsheet and Its Development Flotation: The mica is concentrated by flotation using either of two methods: an amine float in an acid circuit, or the USBM amine-fatty acid float in an alkaline circuit.' The writer does not wish to elaborate on the relative merits of the two flotation procedures; however, after investigating ores from various localities, it was felt that the amine float in an acid circuit was more consistent when using a standard procedure. Iron Reduction and Magnetic Separation: This phase of the flowsheet may be considered the key to the process. It was developed when it became apparent that hot acid leaching had just about reached its maximum effective¬ness for color improvement. S. C. Sun and William Hirsh in "Hydrochloric Acid Leaching of Iron From Pennsylvania Aluminous Clays,"` reported iron extraction for -20-mesh minerals of 82.20% for hematite and only 33.46% for magnetite. The test procedure employs a 19% hydrochloric acid solution, 104°C temperature, and 10% solids. It was felt that magnetic removal of some of the iron contaminants before leaching therefore would be advantageous. Since the iron minerals present as contaminants vary in magnetic susceptibility, it was decided to experiment with reducing reagents as a means of influencing their magnetic properties. Zinc hydrosulfite or sodium hydrosulfite were the reagents used throughout the tests. The procedure developed consists of conditioning the mica concentrate in a closed container at approximately 5% solids with a reducing reagent. Approximately 10.0 lb of zinc hydrosulfite per ton of mica concentrate is used. The ferric iron is reduced to the ferrous state (magnetic) and oxidation is retarded by isolation from the atmosphere in a closed container. After the desired conditioning time has elapsed, the material is passed through a Frantz Ferrofilter where the magnetic particles are retained and discarded as

Jan 1, 1972

By J. Chipman, N. J. Grant, E. C. Roberts

An equilibrium study was made of the distribution of chromium and oxygen between liquid iron, containing less than 1 pct Cr, and simple slags of the CaO(MgO)-Si02-FeO-Cr& type in the temperature range 1526' to 1734OC. The effects of slag oxidation, temperature, and basicity were observed. IN spite of the fact that chromium is one of the most important alloying elements in steel, and exists in almost all steels as a significant residual element, little research has been done to determine its behavior in basic steelmaking processes. Considerably more work has been done under silica-saturated acid slag conditions. Korber and Oelsen,' Herasymenko,' and others have generally agreed that in acid steelmaking practice the chromium in the slag behaved as if it were present as the chrom-ous ion (CrO). Work by Hilty- ir, high chromium slags also indicated that chromium may exist as CrO. In basic slag systems no equilibrium data exist. Based on individual studies of basic open hearth and electric furnace practice, Bardenheuer," Rock-rohr,% nd HauckQ oncluded that: 1—chromium recovery increased with decreasing basicity, and 2— chromium recovery increased with increasing temperature, although the effect was small. In similar studies Yavioskii and Dzemyen' concluded that: 1— slag FeO is the most important variable, 2—the basicity of the slag has no effect on chromium recovery, and 3—slag viscosity is not high even when 20 pct Cr,O, is present. Lapitskii\ oncluded that chromium recovery improved as the basicity of the slag decreased and increased with increasing manganese in the metal. Regarding the effectiveness of CrZ08 as a base or acid in basic slags, both Kristofferseno and Trojer" reported that Cr,08 was an acidic component requiring neutralization as 2CaO-Cr,O,. Experimental Procedure The experimental apparatus and procedure used for the present research were similar in most details to those used by Winkler and Chipman" and were described in detail by them. A magnesia crucible was used, holding 60 to 80 lb of Armco iron which was decarburized with hydrogen to about 0.010 pct C. Since all the metal samples solidified without gas evolution, this carbon level was assumed not to be significant. Synthetic slags made by mixing pure oxides were used throughout the study. Temperatures were measured by means of calibrated W-Mo thermocouples and were checked by Pt-Pt-Rh thermocouples. The range of temperatures covered in this study was from 1526" to 1734°C. The chromium content of the iron was in the range 0.032 to 0.82 pct, although the bulk of the tests showed 0.04 to 0.2 pct. The slags were of the CaO(MgO)-SiO,-FeO-Cr,O, type in which the Cr,O, content was from about 2 to 20 pct, although most of the slags showed from about 2 to 10 pct. The FeO range was from about 10 to 65 pct. CaO and SiO, were in the range of about 5 to 45 pct each, yielding a rather wide range of basicity values. The first 12 heats were made without a sulphur addition, and with only 30 min allowed for slag-metal equilibrium to be reached. In previous research it had been shown that less than 30 min was adequate to achieve equilibrium in slags free of Cr2O8.11,14.15 A study of the present data indicated that some of the tests may not have reached equilibrium in this time; accordingly four additional heats were made in which at least 1 hr was permitted for equilibrium to be reached. For reaching

Jan 1, 1955