Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Bernard Kopelman

THE particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by com¬mercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature, and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. REVIEW OF THE LITERATURE Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.1 When reduction of tungsten oxides by H2 was introduced commercially, 2.1 several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-13 While these many investigations were in fair agreement on the equilibria there arose considerable controversy as to the chemical composition of the oxide between W03 and W02, because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 10o years. Thus Malguti,14 in 1835, decided it was W02.56. In 1857, Riche" proposed the formula W308. Usler,16 in 1865, confirmed the existence of W308 and further proposed W4O11. In 1897, Desi17 agreed upon W308 but also found W5014.

Jan 1, 1946

By Arnulf Muan, R. E. Johnson

Equilibrium CO2 /CO ratios of a gas phase coexisting with selected oxide phase assemblages of the system CaO-"Fe0"-SiOz and vnetallic iron have been determined at 1080°C. The data obtained are used to calculate activity-conzposition relations for metasili-cute, orthosilicate, and CaO- "FeO" solid solutions, and to determine a new value for the free energy of formation of C&S&0,. The metasilicate solution is practically ideal, whereas large deviations from ideality exist in the othe,r two solid solutions. BECAUSE of the geochemical and metallurgical importance of the oxides CaO, "FeO", and SiOz, the system CaO-"FeO"-SiO2 has been the subject of several experimental studies during the past 30 years. Following the delineation of phase relations at liquidus temperatures by a group of investigators at the Geophysical Laboratory of the Carnegie Institution of Washington in 1933,1 Chipman and associates in the early forties2,3 determined activities of FeO in liquids of this system. Since that time, many attempts have been made to interpret the data of Chipman et al. in terms of the constitution of the silicate liquids and the interaction parameters among the various constituents of the system (see for instance papers by Richardson4 and by Flood and coworkers5). One of the assumptions made in some of these interpretations4 is that the binary silicate systems CaSiO3-FeSiO3 and CazSi04-Fe2SiO4 mix ideally in the solid state. The objective of the present study is to provide experimental data on activity-com position relations in solid solutions of the system CaO-"FeO"-SiO2. Such data will contribute toward an understanding of the thermodynamics of silicate solid-solution phases in general, and will serve specifically to confirm or refute some of the assumptions made in interpreting liquid slag behavior. PREVIOUS WORK Phase relations in the system CaO-"FeO"-SiO2 in contact with metallic iron were determined by Bowen, Schairer, and Posnjak,1 and additional phase-equilibrium data for this system have been presented by Allen and snow.' A reproduction of the most up-to-date phase diagram for this system is shown in Fig. 1.7'8 Of particular interest in the present investigation are the relations among the various crystalline phases slightly below the lowest solidus temperature in the system, as shown in Fig. 2. The present work will be concerned primarily with some of the composition

Jan 1, 1968

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Alpha solutes increase the strengths of Ti-Mn alloys through solid-solution strengthening. The substitutional a addition, aluminum, decreases, and the interstitial solutes, carbon and nitrogen, increase the rate of nucleation and growth of a from ß. The best combinations of properties of a-ß alloys are obtained when there is a sufficient quantity of a phase in the structure to dissolve the a solutes. OF the many different titanium-base alloy systems, the predominant alloy type is the a-ß alloy. The properties of the a-ß alloys are dependent on solid-solution strengthening and heat-treatment effects involving the a-ß ratio and transformation reactions. Another variable which influences the mechanical properties of a-ß alloys is the a-stabilizer content of the alloy. An a solute may be present as an intentional addition, such as aluminum, or as an impurity element, such as carbon, oxygen, or nitrogen. It is known that these a stabilizers, when added to titanium, form single-phase alloys which are not heat treatable but which obtain their strength from solid-solution strengthening. Thus, it would be expected that a additions to a-ß alloys would increase the strength of the alloys by solid-solution strengthening of the a phase. In addition, they would affect the transformation kinetics of the ß-to-a reactions and other processes based on the instability of the ß phase. The effects of heat treatment and structure on the mechanical properties of Ti-Mn alloys have been shown in a previous paper.6 This system offers a good base to demonstrate the effects of typical a solutes on the properties of a-ß alloys. The three a solutes described in this work are aluminum, representative of a substitutional a solute, nitrogen, representative of an interstitial a solute, and carbon, representative of an interstitial compound-forming element. The effects of heat treatment and microstructure on the properties of a alloys containing these three elements are described in concurrent publications. Some of these data are used for base-line points in several of the curves used for illustration herein. Experimental Procedures Iodide titanium was used as the base for all of the alloys studied in this work. The alloys were prepared as ½ lb ingots by double arc melting in an argon atmosphere. The ingots were forged to ¾ in. rounds, vacuum annealed for 6 hr at 900°C at a pressure of 10 ' to 10-5 mm of Hg to remove hydrogen, and hot swaged to 1/4 in. diam rod. After me- chanical descaling, test specimens were prepared for heat treatment. The alloys used in this study together with the fabrication temperatures are given in Table I. Heat treatments were done in argon. For the most part, the specimens were sealed in Vyeor capsules under a partial pressure of argon. Quenching was accomplished by breaking the capsule under water. Other cooling methods used included oil quench, argon cool (simulated air cool in an argon atmosphere), and furnace cool. The times for the various heat-treating temperatures are given in Table 11. The tests performed on the alloys consisted of tensile tests on ? in. diam specimens, hardness tests, and microimpact tests. Specimen sizes have been adequately described in a previous publication.' The micrographs presented in this paper were taken from specimens cut from the shoulders of broken tensile specimens. Final polishing was done with Linde B on a slow-speed wheel, and the specimens were etched with a 1½ HF — 3½ HNO, solution. Ti-N-Mn Alloys The transformation diagram and microstructures of the Ti-0.1 pct N-Mn alloys used in this investigation are given in Fig. 1. The effect of small nitrogen additions on the binary Ti-Mn diagram is to raise the ß-transus temperature with little effect on the a solubility of manganese. Also, as has been noted previously,' high manganese-content alloys containing nitrogen, when quenched from temperatures high in the ß field, contain a subgrain boundary phase which appears to be nitrogen-rich a. Marten-site is formed when alloys containing less than about

Jan 1, 1956

By C. B. Post, G. V. Luerssen

It is generally recognized that non-metallic inclusions in steel come from two principal sources. First are the chemical reactions in the furnace, or in subsequent deoxidation, resulting in slag which does not free itself from the metal. Much information has been published concerning these chemical reactions and their control through proper attention to slag viscosity, composition of deoxidizers, and other qualities. The studies of this subject by C. H. Herty, Jr. and others through the medium of physical chemistry have yielded much information for the steelmaker. The second source is erosion of ladle refractories, such as lining brick, stoppers, nozzles and runners, causing entrapped particles of globules of fluxed silicate material. In contrast with the large amount of information available on the first source, relatively little has been published on the subject of erosion which, in the case of basic electric melted steel, is the principal source of nonmetallics. This is probably due to the fact that the problem was assumed to be one of simple mechanical erosion, which could be solved primarily by modification of ladle practices. Good improvements have been made by elimination of slurries in the ladle, better ladle and runner refractories, and more attention to pouring temperatures. It is doubtful, however, that this problem has been recognized in its true light since it is not one of simple mechanical erosion but rather one of chemical reaction between the metal and the refractories; and in this sense is as much a problem of physical chemistry as the reactions involved in the actual steelmaking process. The influence of ladle refractories on the resulting cleanness of steels was early recognized by A. McCancel who examined large inclusions in steels made by both acid and basic practices. His chemical analyses showed the large influence exerted by the manganese content of the steel on erosion of the ladle and nozzles used in those days. The presence of MnO in such inclusions led McCance to the hypothesis that both basic and acid steels react chemically with the ladle refractories so that small globules of fluxed refractories are carried in the stream into the molds. This early work of McCance was checked by one of the present authors on basic electric bearing-steel, and it was found that on steels containing as low as 0.40 pct manganese the fluxed surface of the ladle lining after delivering such a heat showed as high as 25 pct MnO by actual analysis. Furthermore, by lowering the manganese content of the steel to 0.20 pct, ladle erosion was decreased with a corresponding decrease in silicate inclusions in the steel. Limitations placed on the manganese content for the required inherent properties made it impossible to pursue this line further, and subsequent attention was concentrated on improved ladle refractories, care in keeping the ladle clean and free from loose refractories up to the time of tapping, and pouring the steel at optimum temperature. Our study of the chemical reactions at the metal-brick interface between steel and ladle refractories was revived in 1939 as a result of an experimental observation made on the cleanness of alloy steels of the SAE types. This observation showed that the relative cleanness of such steels made in basic electric arc furnaces of 12 ton capacity and poured in ingots ranging from 1100 to 2200 lb weight was determined to a large extent by the ratio of the manganese and silicon contents, provided other steelmaking variables such as tapping temperature, pouring temperature, pouring time, amount of aluminum added for grain size control, and degree of deoxidation in the furnace were kept reasonably constant. Detailed studies made on the deoxidation and slag practice during the refining period of basic electric furnace practice showed that these two variables exerted some influence on the resulting cleanness of steel in the form of bars and forgings. The important variable, the manganese-silicon balance, was not apparent until heats were made in succession by the best furnace practice kept under fairly rigid metallurgical control. Another observation pertinent to this work concerned the similarity in the microscope of slag particles causing magnaflux or step-down indications in subsequent rolled bars, and the patches of slag frequently seen on the surface of ingots. These patches are generally believed to come from the glassy metal-brick interface in the ladle and represent an entrapment of such glass (both from the ladle brick and nozzle) in the metal as it flows over the refractories in the neighborhood of the nozzle. These glassy particles are carried down into the mold with the liquid steel, and gradually coalesce into a slag "button" which floats on the surface of the steel as it rises in the molds. Periodically the button is washed to the side of the ingot where it is trapped between the surface of the ingot and the mold, later appearing as a slag patch on the surface of the ingot after stripping. Even though most of the small glassy particles coalesce into a slag button while the ingot is being poured, it is logical to suspect this step in the steelmaking process as being a source of slag lines large enough to cause trouble

Jan 1, 1950

Jan 1, 1935

Jan 1, 1914

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "housekeeping" items, such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du Pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The input needed from management for the success of conservation efforts will be discussed.

Jan 1, 1981

By John A. Ruppert, John E. Conley

Shortages of cinders, largely resulting from industrial plants converting to fuel-oil, together with an enhanced building activity, have seriously affected the cinder block and lightweight concrete manufacturers. In the search for other sources of lightweight aggregate, various clays, shales, slates and natural occurring lightweight rocks such as pumice, scoria, volcanic ash and the like have received special attention. Methods and equipment for producing suitable lightweight aggregates have been considered. In addition to an expanded use of the rotary kiln, the traveling-grate and continuous-sintering machines are being installed in many localities.

Jan 4, 1950

By George B. Waterhouse

Jan 1, 1933

By Dale A. Augenstein, S. C. Sun

A primary concern in the solution of any solid waste disposal problem is the characterization of the material. In the past, available methodology for the determination of coal refuse characteristics has been severely limited by the inseparable combination of organic and inorganic matter of which the refuse is comprised. The recent development of an electronic, low temperature asher which removes the organic material without alteration of the inorganic constituents has opened new areas of coal and coal refuse research. This study deals with the development of methodology for the characterization of Pennsylvania anthracite refuse through utilization of the low temperature asher. Seven samples of anthracite refuse were examined for verification of the methodology developed and information concerning the characteristics of the refuse.

Jan 1, 1975

By Luther Lennox

DURING the last few years, one of the great problems in the milling of all ores has been that of crushing. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of crushing to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of crushing methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative crushing resistances of a number of ores now being milled in this country and Alaska, the management of the Portland mills requested samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh . screen; in the screen analyses tabulated and plotted herewith, the 150 mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves.

Jan 8, 1918

By William E. Ford, Edward Salisbury Dana

276. Cohesion, Elasticity. - The name cohesion is given to the force of attraction existing between the molecules of one and the same body, in con- sequence of which they offer resistance to any influence tending to separate them, as in the breaking of a solid body or the scratching of its surface. Elasticity is the force which tends to restore the molecules of a body back into their original position, from which they have been disturbed, as when a body has suffered change of shape or of volume under pressure. The varying degrees of cohesion and elasticity for crystals of different minerals, or for different directions in the same crystal, are shown in the prominent characters: cleavage, fracture, tenacity, hardness; also in the gliding-planes, percussion-figures or pressure-figures, and the etching-figures.

Jan 1, 1922

By G. W. Reimers, S. E. Khalafalla

A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum. Magnetic levitation forces can be created as an antigravity field when the fluid is properly placed in an inhomogeneous magnetic field. When the gradient of the magnetic field is directed downwards, the levitation force in the fluid will be in an upward direction to float sinking nonmagnetic bodies by counterbalancing their density mismatch with the magnetic fluid. Several nonmagnetic objects with densities ranging from 2.50 to 11.35-g cm' were made to float or submerge at will in a 0.96-g cm' density fluid placed in vertical magnetic field gradients ranging from 0.1 to 1 kilo-oersted cm-'. The magnetic levitation force in dyne cm' was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1974

Jan 7, 1951

By W. W. Scott

The application of engineering methods to the problems connected with drilling and producing in the oil industry has led to the development of the science that is variously termed "petroleum engineering," "production engineering," "petroleum production engineering," and even Itpolitical engineering." It would require much detail to enumerate the qualifications of a petroleum engineer, just as it would for an engineer in any major industry. For those who have a genuine liking for the oil industry, there is a wide selection of pathways to achievement. The oil industry is now highly specialized. Its products are necessary to all civilized people and are indispensable in the security of our nation and also in the well-being of our families. The business structure of our country depends in a large measure upon oil, and the welfare of this group as individuals is certainly linked with the welfare of the oil industry. What Is the Trend of Engineering? The oil industry offers a fertile field of opportunity for engineering; probably more so than any other industry. The sciences of geology, physics, chemistry and mathematics are all used in some phase of the oil industry and to a very considerable extent in the production division, which embraces the geological, drilling and producing departments. In drilling and production alone, research programs of considerable magnitude are being carried on at this time, and no doubt the future will see a great deal more of this kind of work. Through the cooperation of the engineer, the equipment manufacturer, and the American Petroleum Institute, immense savings have been made by the standardization of drilling and production equipment. Drilling equipment in itself offers a wide scope for study, in that continued efforts are being made to improve the equipment so that it can be made to drill faster and to greater depths. The improvements in drilling equipment are required because new reserves of oil are being found at progressively greater depths. In order to produce such oil in competition with oil now being produced from reservoirs

Jan 1, 1937

ARTHUR BRICE deSAULLES In the death of, Major A. B. deSaulles at South Bethlehem, Pa., on Dec. 24, 1917, the Institute lost a valued and esteemed member, one of the last few of those who, in May, 1871, at Wilkes-Barre, attended the first meeting of the Institute, in response to a call that had been issued by R. P. Rothwell, Eckley B. Coxe, and Martin Coryell. Major deSaulles was born Jan. 8, 1840, at New Orleans, and was the son of Louis and Armide Longer deSaulles, each of French descent. As a boy he was privately tutored in the South, and then schooled in New England to enter the Rensselaer Polytechnic Institute, where he was graduated with honors in the class of '59. Following his graduation he studied in France and Germany for two years, returning to New Orleans in 1861 to enter the Confederate Army, in which he served with distinction- as an engineer throughout the Civil War, rising to the rank of Major and the command of his Corps. After the close of the war he pursued his studies abroad for another year, returning to New York in April, 1866, when be became engineer for the New York & Schuylkill Coal Company, and remained at its plant near Wilkes-Barre until October, 1871, when it was sold to the Philadelphia & Reading Coal and Iron Company.. He then returned to New York where for several years he was engaged in the practice of his profession. In 1869, he married Catharine M. Heckscher, daughter of Charles Heckscher of New York City. Mrs. deSaulles survives him. In 1876, Major deSaulles became superintendent of the Dunbar Furnace Company in Fayette County, Pa., with which company he remained until 1883. As a feature of the Pittsburgh meeting in May, 1879, Major and Mrs. deSaulles entertained the members of the Insti-

Jan 4, 1918

By John Chapman, J. C. Vaughan

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940