Search Documents

By Norman D. Fitzgerald

IN 1943 the petroleum industry completed a series of practical adjustments to the acute problems which dominated the scene a year earlier. The crisis in petroleum transportation from the Gulf Coast to the East Coast was met by the completion of overland pipe lines supplementing emergency haulage by tank car so pressure on consumers along the Atlantic Seaboard was appreciably relieved. Later in the year when the western Atlantic was largely cleared of submarines, the sharp reduction in the hazards of marine transportation permitted the resumption of coastwise traffic and imports from South America. Nationwide restrictions in the use of gasoline and fuel oils became necessary as military demands for all petroleum products mounted to high levels.

Jan 1, 1944

By H. H. Richardson, E. H. Dix

Of all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations would have been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 525" C. to about 1 per cent. at 300" C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540" C., and that this amount decreases to about 3 per cent. at 20" C. In the same year Ohtani and Hemmi3 reported a solubility of 4.8 per cent. copper at 520" C., 2.6 per cent. at 460" C. and 1.5 per cent. at 420" C.

Jan 1, 1926

Impact Transition Temperatures of Some Pearlite-Free Mild Steels As Affected by Heat Treatments in the Alpha Range H. P. Tardif (Canadian Armament Research and Development Establishment, Quebec)—Mr. Josefsson is to be congratulated for his study of a most difficult subject and for the theories proposed to explain the re- sults. One point which, however, might not have received proper attention is that of the shape of the stress-strain curve at the yield point of quenched and furnace-cooled specimens and of specimens strain aged

Jan 1, 1956

By George C. Stone

AS most of you probably know, Australia has had many strikes. The two places that had the worst reputation were the Broken Hill mines and Port Pirie, where the smelter was located. About four or five years ago, the smelter changed hands. The new proprietors - immediately endeavored to get on better terms with the men and made such progress in that respect that, the men came to them and said, "There is no use giving us any more money. You have just raised our pay one- bob a day, but the store-keeper and the boarding-house keeper have raised their prices. The boarding housekeeper raised our board three bob a week and the storekeeper took the rest of it and we are no better off." Learning that what the men needed most was firewood wood the company bought the wood on a tract of ground across Spencer's Gulf and- sent men over to cut it. The wood was brought to the works and given to a man to cut up. He thought he had an easy job and loafed, but when the committee representing the men discovered that his loafing added to the cost of 'the wood, it promptly disciplined him and made -him work as he had never worked before. The next question that arose was the distribution of the wood. The committee got bids from several cartmen whose prices varied from about two to five shillings. It gave the work to the next to the lowest bidder. The fact that if delivering the wood cost more, the user would have to pay for it, was an entirely new idea to the men.

Jan 1, 1920

In the Bowen Basin of central Queensland, coal production has gone from virtually nothing in 1961 to more than 24 million tons today4ut there's a cloud over this success.

Jan 1, 1977

By R. K. Hopkins

For a great many years fusion welding has been used in and around petroleum refineries, but it is only within six or seven years that the more important pressure vessels have been constructed by this process, because before that time the properties of fusion welds would not with-stand such rigorous service. Since the adoption of fusion welding for the construction of this equipment, the refiner has required pressure vessels suitable for operation over a very wide range of conditions. On the one hand, vessels must operate at extremely high temperatures, in the range of 950° to 1000° F., and on the other vessels must be suitable for operation at sub-zero temperatures down as low as -75° F. Also, vessels are required suitable for operation at pressures upwards of 1000 lb. per sq. in., and as low as a 29-in. vacuum. In addition, vessels are required to withstand the attack of very corrosive mediums. It has been a rather difficult task for the fabricator to meet all of these require-ments, but as a result of the extensive research carried on by steel manu-facturers and several fabricators of class I vessels, practically all of these demands have been met. In order to meet the refiners' requirements for this wide range of conditions, the fabricator has worked closely with the metallurgist. This has enabled him to choose the proper base metal for each service condition, but it has been the fabricator's problem to develop a welding rod and welding technique, as well as a heat-treatment, that would produce in the welded vessel characteristics in and around the weld comparable to those in the base metal. Where corrosion is not a serious problem, and where the operating temperatures are not too high, ordinary carbon steel has served very well. But when corrosion is serious, and/or when the temperatures are either very high or very low, it is necessary to use some form of alloy steel to give satisfactory service.

Jan 1, 1935

By A. Ross Rornmel

ABILITY to speak effectively is one of man's most longed for and coveted abilities. It is the ability to stand on one's feet, transfer knowledge and thoughts to others, to reach an objective professionally or otherwise by leading groups through a channel of planned thought. Each day group speaking plays an important part in making or marring success, and the engineering profession often provides this opportunity and requirement. An ability to speak effectively develops courage, poise, confidence, and prestige for the speaker. The technical man cannot be reluctant to face an audience. He is often called upon to do this in presence of employees, supervisors, and other groups. His ability to speak effectively is as much a requirement as the fundamentals of his profession. The three fundamentals of effective speaking are: (1) Enthusiasm and Confidence. These are joined because of their close relation. (2) Preparation. This includes knowledge of the subject. (3) Presentation. By this is meant the features of delivery.

Jan 1, 1946

By A. E. Zawadzki

A progress report is presented on the development of a process for the removal of sulfur dioxide from flue gases. Catalytic oxidation of the sulfur dioxide in flue gases, with the production of recoverable sulfuric acid, has been demonstrated to be technically feasible. Problems associated with the process are discussed. The need for an inexpensive and efficient process for controlling sulfur dioxide emissions from utility plant stacks has been accentuated by the ever-increasing public demand for elimination of all man-made air pollutants. I would like to describe the results of an investigation of the development of such a process; more important, I would like to present a discussion of the problems associated with the process which remain to be solved. The research work on the BCR catalytic gas phase oxidation process has been jointly sponsored by the Association of Edison Illuminating Cos., Edison Electric Inst. and Bituminous Coal Research, Inc., since 1958. However, work on SO2-pollution abatement was initiated by BCR in 1953. Tieman and Clymer,1 working with ozone and simulated flue gases, evaluated a gas phase oxidation process for removing SO2 from flue gases. Their experimental data indicated that the use of ozone to oxidize SO2 in flue gas concentrations, with subsequent recovery of H2SO4, did not appear to be economical due to the large ratio of ozone to sulfuric acid produced (2.6 to 1). The cost of the ozone would be 6 to 10 times the cost of sulfuric acid produced. As a result of the ozone study, work on a catalytic oxidation process was developed. The following reactions are the basis for the catalytic oxidation process Reaction [I] normally occurs in the combustion of sulfur-bearing fuels. At the high temperature found in the combustion chamber, 95% to 99% of the sulfur in the fuel is oxidized to SO2 and 1% to 5% is oxidized to SO3. The concentration of SO2 in the combustion gases depends on the combustion efficiency and the quantity of excess air used. A commonly used rule of thumb is 0.1 percent by volume SO2 in the flue gas for each 1% sulfur in the fuel. Reaction [2] proceeds at a wide range of temperatures. The rate of the reaction is rapid above l,000°F; however, the equilibrium conversion drops rapidly above this temperature. 2 Reaction [3] occurs rapidly to completion at temperatures below 400°F; above this temperature some SO3 exists in equilibrium with H2SO4. Complete dissociation of H2SO4 occurs above 650°F.3 The simplicity of the proposed process provided added incentive to the development and evaluation of the various component unit operations. The advantages of the process were considered to be as follows: 1) no raw materials were required, 2) the unit operations were not radically new; and 3) a salable product, sulfuric acid, would be produced. The successful development of the process was contingent upon the solution of several major problems: 1) The development of a catalyst which would provide high catalytic activity at reasonable conditions of gas flow and temperature without causing an unacceptable increase in pressure drop. 2) The development of a high temperature dust collection system to provide clean flue gases to the catalytic reactor. 3) The complete recovery of the sulfuric acid produced in the process; the effluent gas must contain less than 20 ppm by volume of sulfuric acid. As of this date, the complete solution to these problems has not been achieved. EXPERIMENTAL Catalyst Development: The use of platinum and vanadium catalysts for the production of sulfuric acid by the treatment of dry gases containing 5% to 20% by volume sulfur dioxide has been known for many years. The application of the basic idea of catalytic oxidation of sulfur dioxide in flue gas concentrations was

Jan 1, 1965

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

Jan 1, 1931

By Harold G. Moulton

IT is highly significant that engineers should seriously consider the interrelations of technology, economics, and government. It is indicative of the emergence of maladjustments and problems that perplex our thinking and frustrate our activities. Instead of a world in which scientific discoveries and their applications through engineering to the processes of wealth production are regarded as the royal road to progress, we now find science and engineering being made responsible, in no small degree, for our economic and social troubles; and the powers of government are even being invoked to stem the tidal wave of technology. Indeed, there is a deep-seated fear, manifested in the writings of some of our greatest scientists as well as in popular discussions, that science may destroy our civilization.

Jan 1, 1938

By Sherwin F. Kelly

THAT gold ores occur in Georgia is a fact apparently not widely known outside of that state, yet in the last hundred years nearly $18,000,000 worth of gold has been mined there. The discovery of gold-hearing quartz was made in 1823 on the "Forty Acre Lot" (which now belongs to the Columbia Mining Co.), in McDuffie County, and about seven years later the first stamp mill on record was erected near there. In recent years Georgia's gold production has dwindled to an insignificant figure. However, with the increase in gold price, interest in this district has been revived, so an electrical geophysical survey was undertaken to aid in discovering new quartz veins, on a part of the Forty Acre Lot, the adjoining Hamilton mine, and the nearby Woodall property.

Jan 1, 1934

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By R. W. Raymond

The immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages—in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, me Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley's process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. What Did Mr. Gayley Invent? Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley'a first patents. It may be admitted, without such critical analysis, that the possible advantages of removing moisture from the air forced into an iron blast-furnace were recognized and talked about a hun-

Jan 1, 1909

By H. E. McKinstry

LIKE nearly everything else, mining geology has been reconverting. Many geologists had been in military and other government service. Many more, with mining companies, had been working primarily toward increasing production from known reserves. All of these are turning now toward their normal peacetime endeavor-the search for new ore; for most mining companies, finding themselves with accumulated deficits in development work, are more than ready to go ahead with their postwar plans made a year or more ago but still stalled at the close of 1945 for lack of man power. These plans include not merely development in the old home camp but also wide exploration for new prospects both domestic and foreign. Most of the large concerns have geologists and engineers in the field in the United States, despite the outlook for higher mining costs here, and at least half a dozen strong American companies are already investigating opportunities abroad, notwithstanding past unhappy experiences in certain Latin-American nations which have welcomed capital but later found means of preventing investors from reaping the reward of their enterprise. A few of these new foreign expeditions are following well-planned programs, but too many, in their haste to get any sort of footing, are proceeding without well-considered policy. with the result that their geologists can do little more than desultory scouting.

Jan 1, 1946

By William C. Peters

The pre-production interval, beginning with the recognition of an orebody's best potential and ending with significant production, contains time-dependent conditions well appreciated by miners but not always understood or appreciated by the landowners, investors, and legislators with whom a miner must deal. The expression persists, even outside of Western fiction, that someone has "found a mine." From a slightly more knowledgeable position, the question is asked "How long does it take to make a mine?" and an all-encompassing answer is expected. By scanning the discovery and development history of hundreds of mines and rejecting those which involve rehabilitation or expansion of older mines, some generalizations can be attempted. It should be kept in mind that while physical conditions involving the geology of the orebody and the geographic surroundings do not change markedly with time, technologic and economic conditions do change from year to year. The new methods, facilities, markets, land tenure, and politics form a pattern in which today's mines are made and which do sometimes modify the pre-production interval.

Jan 8, 1966

By AIME AIME

THE following Officers, Directors, and guests were present: Herbert Hoover, A. R. Ledoux, Henry S. Drinker, Edwin Ludlow, Samuel A. Taylor, Charles F: Rand, William M. Corse, Arthur S.. Dwight, Glen H. Clevenger, L. W. Francis, F. G. Cottrell, Bradley Stoughton, Percy E. Barbour, E. P. Mathewson, Dorsey A. Lyon, Archibald Douglas, A. D. Flinn, RobertLinton, James F. Kemp, William Y. Westervelt, J. W. Richards, W. L. Saunders, George Otis Smith, Thomas T. Read, J..C. Murray, Ralph Arnold. A Committee on Mine Equipment was appointed composed as follows: Graham Bright, chairman, William Kelly, Howard N. Eavenson, R. E. Hobart, and S. P. Rumsey. B. D. Saklatwalla was added to the Committee on Miscellaneous Metals and W. Spencer Hutchinson was added to the Committee on Mining Geology. A revised budget for 1921 was approved. A petition duly signed to amend Section 1., of Article III of the Constitution, increasing the initiation fees from ten dollars to twenty dollars, was approved by the Board.

Jan 1, 1920

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By J. W. Pugh, J. D. Nisbet

F. B. Foley—The use of data published by Wever and Jellinghaus in 1931 to fix boundaries of the sigma phase in the Fe-Cr system, in the face of the author's own references to the suggestions of Bradley and Goldschmidt, Aborn and Bain, and Hougardy that the phase is much more extensive, and the very much more accurate work, which weighs heavily in favor of these suggestions, of Cook and Jones, published in 1943 and evidently disregarded by the authors, makes their derived ternary diagram, especially fig. 15 for 400°C, quite inaccurate on the Fe-Cr side and affects the extent of phase boundaries in the most controversial and important part of this ternary system. In commercial Fe-Ni-Cr alloys the occurrence of sigma has been observed time and time again at lower chromium contents than that of the 24 pct Cr, 16 pct Ni, 60 pct Fe alloy which is the lowest permitted by fig. 15 of practically carbonless metal. Newel1 reports sigma in 27 pct Cr-Fe even with some carbon present to be one of the greatest detriments to its extensive application, whereas Pugh and Nisbet set a low limit of 36 pct Cr for sigma in the binary Fe-Cr system. J. J. Heger—The diagrams presented by the authors do not agree with observations made on commercial Fe-Cr and Fe-Cr-Ni alloys, nor do they agree with two recent investigations made on the Fe-Cr and the Fe-Cr-Fe systems. I refer first to the investigation made by Cook and Jones1' on the sigma region of the Fe-Cr system. On the basis of their results which were published in 1943, Cook and Jones established new boundary limits for the sigma and the alpha plus sigma regions. These new limits have been accepted and are incorporated in the Fe-Cr diagram that appears in the 1948 edition of the Metals Handbook. This diagram is shown here as fig. 34. As will be noted, the boundary limits of the alpha plus sigma region in this diagram extend to much lower chromium contents than do those in the diagram presented by the authors in fig. 2. These new limits indicate that sigma phase should form in an Fe-Cr alloy containing 26 pct Cr, and experience with commercial alloys confirms this finding. Indeed, recent studies on a commercial Fe-Cr alloy containing 17 pct Cr have shown sigma phase to be stable in this alloy at 550°C. I recognize that the authors' work did not include studies on the sigma region; however, I believe this is a serious omission because sigma phase may profoundly affect the physical properties of these alloys and should be evaluated in any investigation which attempts to relate physical properties to the equilibrium diagram. The second investigation to which I refer is that made on the Fe-Cr-Ni system by Rees, Burns, and Cook,'' who used pure alloys and employed heating 17 W. P. Rees, B. D. Burns, and A. 3. Cook: Journal Iron and Steel Institute. (July 1949) 162, Part 3. p. 325. times that extend to 200 days. These investigators published their results in July 1949 and from these results constructed isothermal sections at 800" and 650°C. The isothermal section at 650°C is shown here as fig. 35. This diagram indicates sigma phase should form in a pure 18 pct Cr-8 pct Ni alloy. Although sigma phase has not been observed after 10,000 hr at 1200°F in commercial 18-8 alloys containing carbon and nitrogen, it has been observed under the same conditions in 18-8 alloys modified with titanium and columbium, both of which serve to reduce the effect of carbon and nitrogen. This section and the one at 800°C suggest that the constant iron sections which are presented by the authors, should be considerably altered, if they are to represent an accurate picture of the system. A few of the suggested alterations are as follows: In fig. 9, the section at 50 pct Fe, the gamma plus sigma region should be widened, not narrowed at 800" and 650°C. In fig. 10, the section at 60 pct Fe, the gamma plus sigma region should be widened at 800° and 650°C. In fig. 11, the section at 70 pct Fe, an alpha plus sigma, an alpha plus gamma plus sigma, and a gamma plus sigma region should be added. In fig. 12, the section at 80 pct Fe, the alpha plus gamma region should be widened at 800°C. In fig. 13, the section at 90 pct Fe, the alpha plus gamma region should be widened at 650° and 800°C. Undoubtedly, the chief reason for the discrepancies between the authors' data and those of Rees, Burns, and Cook is that the authors did not employ long enough heating times to allow for transformation. In this connection, I wish to warn that transformations in these alloys, particularly transformations at temperatures below 800°C, are extremely sluggish and may require a year or more to approach completion. Therefore, unless extremely long heating times are employed or steps are taken to accelerate these transformations by such means as mechanical working, the results will not yield an accurate picture of the alloy system. Certainly, an accurate picture is needed for the development of better high-temperature materials. E. J. Dulis-The purpose of this work is not clear. If an improvement of the ternary equilibrium diagram of the Fe-Cr-Ni system was wanted, it seems logical that testing techniques superior to those previously used would be a prime requirement. To approach equilibrium in this system, long holding times are needed; a fact established long ago but apparently ignored by the present authors, who used the continuous heating and cooling tests in equilibrium studies. A publication on the same system by Bradley and Goldschmidt6 was criticized by Monypenny in a

Jan 1, 1951

By Albert A. Mathews

OUTCROPS of gypsum rock near the present site of the city of Gland Rapids, Mich., were known to fur traders early in the nineteenth century. However, the deposits seemed without value and were not worked for some time. So far as cat1 be learned, Michigan gyp- sum was first used by a plasterer who settled in Grand Rapids in 1834 as a member of its fourteenth white family. In building a house for one of the early traders, be used some otnamental stucco mouldings manufactured from the local gypsum deposits for decorations in the gables and around some circular windows. The gypsum was broken out with a hammer, ground in an Indian corn mill, and burlled in a caulclron kettle,. After two attempts, the ornaments were successfully set, and remained on the house until it was destroyed by fire in 1850.

Jan 1, 1936