Search Documents

By Evan Jannoulakis, Wilfrid Comeau

Using the Scaled Distance (SD) and the vector sum Peak Particle Velocity (PPVvs) from a single delay, preferably single blasthole, in a shot, a number is derived which has shown itself to be consistently related to blasting efficiency, as experienced by one of the authors of this paper over the last thirty years. The numbers derived by this process range in value over one order of magnitude more or less. This variation, a function of distance, weight of explosive in the delay, blasthole diameter, blast design, powder factor and the geological environment, can be consistently related to two of these factors, powder factor and distance. In actual use the measured "BED" representing good blasting results should not vary by more than + 33 to + 50 percent of the estimated "BED" in non calibrated cases, and + 10 to 20 percent where previous experience is available. Relatively high "BED" values are indicative of poor blasting results while relatively low "BED" values may be precursors of poor blasting results in a shot. There are many variables in the geological environment which can affect the "BED". A case study is presented from a surface coal mining operation in eastern Canada. This case study tries to evaluate the reasons for the variability in "BED" values derived from multi-hole shots. A problem in using "Signature Vibrations" from a single-hole shot to predict blasting vibrations from multiple-hole production shots is identified.

Jan 1, 1998

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986

By W. F. Visser

The growing availability of information and data analysis capabilities provides new opportunities for improving the performance of operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits the rapid evaluation of changes and fast business improvement decisions. This paper presents a blueprint for system alignment, organizational design and management practices to leverage these developments in performance-driven operations management in mining and mineral processing.

By W. F. Visser

The growing availability of information and data analysis capabilities of recent years provides new opportunities for improving the performance of mining operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits rapid evaluation of changes and fast business improvement decisions. This article presents a blueprint for alignment of systems, organizational design, and management practices to leverage these developments in performance-driven operations management in mining and mineral processing. The first component of the blueprint is a performance framework with a system of key performance indicators for production control that can be used across organizational levels. This system places improvement at the core of management activities, giving greater importance to improvement skills at lower organizational levels, so companies can leverage available information for improving operational control. Secondly, the blueprint defines an organizational structure that strengthens performance improvement with technological and change management capabilities. Finally, the blueprint proposes alignment of management practices, covering the optimization of short-interval controls, the application of an improvement project portfolio management system that determines the ownership of improvement projects, and the coordination of controls across the organization. This combination of systems, organizational design, and management alignment supports rapid decision-making at the right organizational level. Introduction of the presented blueprint for operations management enables mines to leverage the developments in information and analysis capabilities to improve the performance of operations.

By Sherwin F. Kelly, Bela Low

THE WORK OF THE DRILLER and of the oil geologist is seriously handicapped by the impossibility of actually seeing what is going on inside a borehole as it is being drilled. Visual information of the position and condition of the casing, and of the characters and attitudes of strata passed through would be of inestimable benefit. The best substitute for putting a periscope down a hole is the taking of photographs of its interior at points where information is desired. An apparatus for this purpose has been constructed by Dr. Thomas Reinhold, of Heemstede, Holland, and one instrument of his design has been put into practical use by the Geological Survey of The Netherlands in searching for water. To the best of our knowledge, this instrument has not been applied to oilfield problems, although the possibility has been mentioned in the one or two brief notices of the camera which have appeared in the literature.' The purpose of presenting this description of the instrument, with some examples of its work, is to suggest that it might be adapted to serve a variety of useful purposes in American oilfields, and with the hope that discussion will bring out any modifications necessary to make the apparatus more valuable to drillers and geologists.

Jan 1, 1932

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By P. J. How, T. O. Hagan, M. F. Handley

Inelastic deformation of highly stressed rock in deep mines needs to be quantified in both time and space. Since most deformation occurs by shear, continuous monitoring of discontinuities in the rock from boreholes holds promise. The casing. Al interpretations of shear movements are based on a simple relation between shear displacement and the resulting change in tilt of the sensor. A prototype has been constructed and has undergone laboratory trials with satisfactory results. Underground trials will commence shortly. The instrument as designed has the potential for other applications, both in the civil-engineering and mining industries. paper describes an instrument that is both cheap and reliable, and capable of monitoring such shear movements continuously. The principle of operation is based on two capacitive gravity sensors mounted orthogonaly to each other in a sealed aluminum

Jan 1, 1988

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By C. Sampaio, C. Petter, M. Veras

"INTRODUCTION Use of sensor technology applied to the gravimetric beneficiation is intended for the selective preconcentration or separation of various minerals. Sensor Based Sorting (SBS) uses sensors to identify the particles and separate them by a mechanical process (flap) or pneumatic ejection valves (Wotruba et al. 2014). The principle of the SBS technology to separate mineral particles consists of three phases which cover feed,detection and separation. (killmann, 2009 Apud nienhaus et al. 2014). The applicability of the technique in an early stage of beneficiation enables free particles and poor grade to be a part of the process. The mass of tailings to be processed can be removed at the initial stage to save energy, water and equipment maintenance (Wotruba et al. 2014). Lindner (2010) suggested that the use of SBS technology would only will be possible if there exsists an electromagnetic interaction in all the wave spectra interacting with the solid ore. The interaction of electromagnetic waves depends directly on the characteristics of the material. The material receives a spectrum of electromagnetic waves by irradiation and this results in a reduced wavelength with differing types radiation such as fluorescence, reflection, remission, absorption, transmission and transmission. The frequency of the wave spectrum varies between 1000 and 1020Hz, illustrated by the data in Figure 1, which shows that each type of sensor emits a wavelength inversely proportional to the frequency ranging from 10-11pm to 104km, and the frequency that varies between EHz 103 and 1020kHz. The difference between the electromagnetic spectrum variations can only be visible to the human eye at wavelengths with intervals between 380nm and 780nm (Wotruba et al. 2014). One of the main advantages of operating with imaging sensors is the versatility of the images which can take on zero, one, two or three dimensions shown below as a point, a line, an area or a spatial image, as illustrated in Figure 2. According to Schubert (1988), to separate a mineral particle it is necessary to follow the characteristics of mineralogy, physics and chemistry with or without use of water. The use of new technologies can help reduce operating costs and improve utilization of mineral resources."

Jan 1, 2016

By Roger A. Harris

INTRODUCTION The Kidd Creek Mine produces a total of 3.6 million tons annually. Geologically the orebody is complex, containing rich values of zinc, copper, silver and lead which are mined and milled as two separate "ore types". Production is mainly from highly mechanized sub-level open stopes of approximately 300,000 tons each. The Mine Engineering Department has developed, and now operates, a computer system that is the subject of this report. It was created specifically to aid the daily work of the mining engineer and has features that are new and possibly unique in the industry. DESIGN OBJECTIVES In 1971 a task force, set up to investigate the subject of computer assistance to mine engineering, specified four design requirements which it felt a successful application had to satisfy. They were:- 1) The computer had to offer a TOTAL SYSTEM that was fully integrated into the routine mine engineering function. 2) The computer had to be directly usable by the current engineering staff, the majority of which had received no formal training in computing.

Jan 1, 1977

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

INFACON conjures up many things for many people. For the fortunate few who have been actively involved with this event since its inception, it brings back memories of far places, stimulating debates and above all, the people who have over the years contributed to the outstanding success of the Congress and who have added to the wealth of knowledge on all aspects of ferroalloys. The International Ferroalloy Congress (INFACON) has been held every three years since 1974. INFACON X will be held in Cape Town in February 2004. Simple arithmetic shows that next year?s Congress should in fact be INFACON XI. Thus, one Congress was skipped. INFACON 74, as the name implies, was held in 1974, in Johannesburg, South Africa. The event was sponsored by the Ferro Alloy Producers? Association of South Africa (FAPA), the National Institute for Metallurgy (NIM - Mintek as it is known today) and the South African Institute of Mining and Metallurgy (SAIMM). You will see some of the same sponsors involved in INFACON X. Dr. Robbie Robinson, renowned academic and past president of the SAIMM, was the Chairman of the Organising Committee. The editor was Dr. Helen Glen. Anyone fortunate enough to possess a copy of the proceedings of this first Congress will agree that from a literary and technical perspective, it is still the benchmark for subsequent events. A unique feature of INFACON 74 was the use of rapporteurs (my first duty) to ensure that the discussions following the presentations were recorded (in direct speech) as accurately as possible. This involved time-consuming correspondence (can you imagine life before e-mail?) to all parts of the world between the author and the person posing the question, with the rapporteurs acting as go-betweens. It is understandable that the much-awaited proceedings only saw the light in 1975. The names recorded in the proceedings as the members of all six committees read like the who?s-who of the South African ferroalloy industry at the time: Dr. Peter Jochens, Mr. Harvey Reid, Mr. Piet Streicher, Prof David Howat, Mr. Sigurd Selmer-Olsen - to name but a few. The Congress was held in the new, very fashionable and upmarket Carlton Hotel in the CBD. In the Foreword of the proceedings, Dr. Robinson provides an insight into the event. Three hundred and thirty six delegates from twenty two countries attended the Congress, which was opened by the Honourable P.G.J. Koornhof, Minister of Mines. Again, the opening address makes fascinating reading. During the Congress an ad hoc committee was convened as the first International Committee on the Organisation of Ferroalloys Congresses, with representation from the main ferroalloy associations of the world. The following decisions were recorded: ? The Congress would be continued at three-yearly intervals under the name of INFACON ? Every third Congress would be held in South Africa ? NIM (Mintek) would provide the permanent secretariat. Six technical sessions were held, each preceded by a plenary address with a closing address by the session chairman. In all, thirty technical papers were presented. Prior to the closing address, a panel discussion on factors affecting the future of the ferrochromium industry provided stimulating debate in the form of a question-and-answer session. The hosting country for the next INFACON would be announced. Eventually, word got round that the next INFACON would be held in Japan. However, due to unforeseen circumstances, the event was cancelled ? thus no INFACON 77. INFACON 80 was subsequently held in Lausanne, Switzerland from 12th to 16th October 1980. The event was organised by IFPEO, Institut des Producteurs de Ferro-Alliages d?Europe Occidentale. The Congress was officially opened by the President of IPFEO, Mr. R. Björklund, who was also President of the Organising Committee. The technical sessions were held in the Palais de Beaulieu. The Congress was well attended by 400 participants from 28 countries as well as 100 accompanying ladies. A total of four plenary addresses and 18 technical papers were presented. As with the first event, an international panel discussion (questions and answers) preceded the closing address. In his closing address, Dr. Louw Alberts, Chairman of the International Committee on Ferroalloys and President of NIM, presented an insight into the factors affecting growth in the industry and where growth was likely to take place. Twelve exhibitors had stands at the Congress. Attendees could choose from four post-event tours to Belguim/France (SADACEM/Compagnie Universelle d?Acetylene et d?Electro-Metallurgie), France (CUAEM), Finland (Outokumpu Oy) and Norway (Elkem Fiskaa plant).

Jan 1, 2004

Sixty years after its inception, after an alternation of periods of admiration and rejection by the industry, Sampling Theory can now be seen as going through its golden age. A brief history of its successive transformations and progresses achieved by its author, Pierre Gy, and his followers, reveals the theoretical as well as practical difficulties that had to be vanquished to reach this point. Its current level of acceptance and corresponding trends are discussed and illustrated, with an insight on its increasing real role in the industry and future prospects for its further development.

Jan 1, 2008

By S. D. Prosser

The earliest record of slag in the world was the discovery of the remains of a copper blast furnace in Southern Israel, which has been carbon dated at 3500BC, nearly 6,000 years ago. Slag in Australia is a much more recent phenonenum with the first iron blast furnace commencing operations in 1848. The early days of metal smelting in Australia were marked with many company failures due to a variety of reasons. This paper traces the progress of metal and slag production from those early days up to the present times

Jan 1, 1994

By B. Blaschuk

The Freeport McMoRan Bagdad Solvent Extraction (SX) circuit is the oldest plant of its kind currently in operation. The plant was commissioned in 1969 and was the second SX-EW operation to be built following the Ranchers Bluebird solvent extraction and electrowinning (SX-EW) plant near Miami, Arizona. Over the years of operation, the configuration of the SX has gone through many changes to accommodate a variety of pregnant leach solution (PLS) grades and flows. Although modifications to the original plant configuration are numerous, the Bagdad SX circuit has maintained its general form consisting of multiple long and narrow settlers. The unique configuration of the Bagdad SX circuit presents a variety of operational advantages and challenges; however, it continues to operate at a level recognized in the industry as excellent.

Jan 1, 2010

By D. G. Crosby

This paper defines the Canadian offshore areas, comparing the juridical continental shelf with the physical one. The question of jurisdiction and ownership is dealt with, and the setting out of resource administration lines to divide areas of federal and provincial administration is explained and illustrated. Offshore activity is reviewed and prospective areas for future work are mentioned.

Jan 1, 1969