Search Documents

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

A short account is given of the theory and practice of determining the true U3O8 content of ore samples by the determination of the beta and gamma activities separately, using the method of Eichholz and his associates.It is shown that, despite the variation of sample activity without change in U3O8 content, the true U3O8 value can still be found.Thorium can be determined simultaneously if this element is also present.

Jan 1, 1957

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Chia-Chi Chiu, Meng-Chia Weng, Tsan-Hwei Huang

"This paper proposes a biconcave shape bond model for the distinct element method (DEM) to simulate cementation between two circular particles in geomaterials. Rather than an original parallel bond model between particles, the proposed model adopts the more realistic shape of cementation and considers the elastic response of cementation under external loading. The stress field and force-displacement relationship of the biconcave shape bond is based on Dvorkin’s theory, and three modifications are adopted: (1) A superposition method is applied to improve the correctness and symmetry of the stress field, and it also provides a method of addressing the status when both connected particles rotate; (2) To simplify the input parameters, the tangential movement is replaced by the normal deformation and rotation between particles; (3) To accelerate the calculations, variables are extracted in analytical procedures, which provide an efficient method for applying the bond model with only one matrix inversion. With these three modifications, the new biconcave shape bond model is created.To assess the validity of the proposed model, this study compared the elastic deformation in a single bond with an elastic analysis performed using the finite element method (FEM). After verification of the proposed model, a series of sensitivity analyses was performed to explore the effect of bond shape and the differences from the parallel bond model. For a single bond, the results showed that a biconcave model can represent the mechanical behavior of a biconcave shape bond and is effective with different bond shapes. The stress fields calculated by the biconcave model were more similar to the FEM results than those obtained using Dvorkin’s theory. The width and thickness of a bond have a considerable effect on its stiffness, and the variation of thickness decreases with the width of the bond. In addition, the required parameters can be acquired directly from real bond material rather than using the back analysis procedure for parameters.The biconcave model was further implemented in DEM software Particle Flow Code 2 Dimension to certify its applicability in geotechnical engineering. Using this model, a series of uniaxial compression test simulations was performed to analyze the macroelastic responses of specimens. The results showed that the macrotangential elastic modulus and Poisson’s ratio had a regular tendency, and they agreed with the stiffness variation in a microbond. This finding can assist in determining correlations between microand macroproperties and provides an innovative method for simulating the behavior of cemented granular material."

Jan 1, 2015

By Russ Darr

New methods and techniques in the field of hydrogeology are being developed constantly. One of these advances has been brought about through the use of inexpensive microcomputers. The formulas used in this paper and developed by Theis, Jacob, Glover, Keck, and Dupuit are not new. The methods by which these formulas can be solved are now available to all who wish to get faster, less expensive, and more reliable answers. These methods involve the solution of standard groundwater formulas using microcomputers. Examples and case histories of these methods are presented

Jan 1, 1980

By J. M. Dempsey, R. A. Litle

Asarco Incorporated’s Omaha, Nebraska refinery site and the City of Omaha’s downtown redevelopment projects are the perfect example of the marriage of the Brownfield and Sustainable Development strategies. Nebraska’s largest voluntary site remediation project created a focus point for redevelopment and has spurred over $1 billion in economic investment within a 1-mile radius of the site. Asarco was faced with options of very expensive and uncertain facility upgrades or a shutdown. Local leaders, Asarco, and regulators worked together to convert a controversial and complex site to a park-like redevelopment area with numerous long-term benefits to the City and the environment.

Jan 1, 2004

By Theophilus Mensah, Kwame Awuah-Offei

Engineers face significant challenges when determining what geometry provides the most profitable and safe stope for extraction. Several techniques and optimization algorithms have been developed in recent years, but most fail to find optimal solutions because they are heuristic or LP-based without efficient geometric constraints. This paper presents a two-dimensional binary linear programming (BLP) model for determining the optimal combination of blocks in a stope that maximizes the economic value of the layout of stopes for a sublevel deposit. The work draws from Queyranne and Wolsey’s (2017 & 2018) formulations of tight constraints for bounded up/down times in production planning problems to formulate novel and efficient geometric constraints along with geotechnical and grade constraints for the BLP stope layout optimization problem. Results from the model indicate that it is possible to formulate efficient shape constraints in LP-based approaches. The model used for the numerical example contained 144 valuable blocks out of 774 blocks, which translates into an economic value of $53.21M. The BLP model selected 60 valuable blocks and 13 waste blocks that met all constraints translating into a maximum economic value of $34.4M in 1.83 hours within a gap tolerance of 0.00%.

Jun 25, 2023

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By E. B. McNew, J. M. Barnes, A. E. Torma

The applicability of biosorbent materials for the removal of uranium and other heavy metals from synthetic and actual uranium mil 1 tailing (UMT) solutions has been investigated. The biosorbent materials used in this study were barium loaded beads of alginate, alginate-dextran sulfate, alginate-carrageenan, and alginate-xanthan gum. These studies were performed in stirred vessels and packed columns. It was observed that 100 percent of the uranium could be removed from a synthetic solution following 2 hours of contact time in a stirred vessel, and 80-100% of U, V, Mo, Mn, Sr, and Zn could be removed from a UMT effluent solution with a packed column. Kinetic evaluations were performed, using a generalized rate equation, on the biosorption of uranium with these barium loaded beads.

Jan 1, 1992

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By COREY C. BRAYTON

OUR first air travel began at Barranquilla on a trip to the platinum dredging-operations at Andagoya. The fare is based on a minimum weight of passenger, and I will have to admit that the minimum is too low. To make this trip by boat would have necessitated going back to the Canal, thence down to Buena Ventura, and up the San Juan river, which would have taken, counting delays, two or three weeks. The time by Scadta airplane was six hours. We stopped at Cartagena for a day to look over that historic city. The route from there lay along the north coast to the mouth of the Atrato river, then up this river, over the jungle, and over a divide some 300'ft. in elevation and down the San Juan river a few miles to Andagoya at the junction of the Condoto. The General

Jan 1, 1930

By T W. C Stambolie

Coalmines, like any other mine, generally involve the classic three-staged approach to mining studies; namely concept, pre-feasibility study (PFS) and feasibility studies (Cusworth, 2012). Subsequent to these studies, and in instances parallel to these studies, the commitment to an environmental impact statement (EIS) is made in order to secure both state and federal development consent. In recent times, the sentiment to both mining and coal is changing whereby the traditional approaches to mine planning and economic evaluation is complicated by evolving environmental legislation, expectations and time frames. It is all too common to take shortcuts in the development of projects in order to create the perception of cost savings and expediting the delivery timeline. Atkins (2016) points out that: boards of so many small to mid-tier mining companies, and a few majors, focus on relentless project delivery too early in the project process, with so little time and effort applied to risk analysis and option development. Unforeseen risks can cost any timeline or budget far more than the effort required assessing and mitigating these. The ultimate risk to any feasible coal project is that of environmental approval and achieving development consent.CITATION:Stambolie, T W C, 2016. A black canvas – planning a greenfield coalmine in New South Wales, in Proceedings Life-of-Mine 2016 Conference , pp 31–35 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R. R. Smith

The meaning of the title, "Blank Piece of Paper," refers to the need for management to take a completely fresh viewpoint to the problems facing our industry. These problems are so severe and some so new that conventional thinking may not be adequate to resolve them. Innovation has to be a part of every company's approach to the solutions, our concept is to start with a "Blank Piece of Paper.' The objective of 'this paper is to outline steps which can be taken to improve the profitability of a mining business. This is not an examination of technical solutions to individual problems, but rather recommendations for overall change in management thinking. This philosophy is based on our actual, hands-on experience in major open pit operations worldwide over the past 25 years.

Jan 1, 1987

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By Brian C. Maynard

"Blast design is becoming more and more important as industrial limitations change in regard to economical and physical restraints. Certainly there are ways to alter the nature of the blast by using different explosives, various hole sizes and modifying the timing and charging details. However, it is not possible to alter the fabric of the rock mass. Therefore, it is necessary to learn more about the rock mass and its role in the blast design, and the resulting fragmentation. The major determinant in the degree of fragmentation, or lack of it, is proposed to be the inherent fragmentation of the in situ rock mass. A practical method of quantifying the discontinuities existing in the rock mass is presented and discussed. Likewise, the effects of inherent fragmentation on the resulting muckpile are reviewed. Finally, a fragmentation model combining the calculated inherent fragmentation and the Kuzram model is shown using a sample blast.IntroductionIn blasting, discontinuity characteristics (Fig. 1) control the method by which the rock mass will behave. Research carried out by Piteau (1970) showed a number of characteristics important in engineering design and, as proposed, in blasting processess. These included:• the nature of their occurrence (i.e. sets or isolated);• orientation and position in space;• continuity; and• intensity"

Jan 1, 1990

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008

By D Linn Coursen

Detonation propagates in the subject blasting agent at about 2.7 km/sec when it is heavily primed but explosion propagates in it at only about 0.43 km/sec when it is lightly primed. When propagating at 0.43 km/sec, it produces a borehole pressure that is slightly less than 1 kb, but no yellow fumes or other sign of incomplete reaction. It is a pumped AN/emulsion blend to which additional water is added by circumferential injection at the inlet of the hose through which it is pumped.

Jan 1, 1994