Search Documents

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By K. Ohmori, K. Takeya, S. Yoshizawa, A. Kawamoto, T. Ishikawa

"High performance Sm2Fe17N3 magnet powder is developed nitriding Sm2Fe17 alloy that 'is made using a reduction and diffusion method. Typical remanence, coercivity and maximum energy product of the fine powder are 1.40 T, 1.13 T and 323 kJ/m3, respectively. Decreasing samarium content, oxygen content and the amount of a-Fe are found to be the important factors to realize high-energy product.High performance injection molded Sm2Fe17N3 anisotropic magnet is also developed using the powder and an original binder system developed in order to mold at low temperature. Typical remanence, coercivity and maximum energy product obtained are 0.77 T, 0.78 T and 103 kJ/m3, respectively in the density of 4.77 Mg/m3The temperature coefficient of remanence is -0.07 %/K and that of coercivity is -0.54.%/K. The initial irreversible flux loss of the magnet that has a permeance of two is -5 % at 100 °C and the irreversible .flux loss of it is -4.4 % exposing it at 80 °C for 1000h.IntroductionSm2Fe17N3 alloy powder is expected to be very useful for a bonded magnet. The reasons are as follows. The magnetization is as large as the Nd2Fe14B alloy. Curie temperature is even higher than the alloy. The uni-axial anisotropy is comparatively higher than the alloy. Consequently it is possible to obtain high coercivity after just milling the powder and therefore possible to obtain high-energy product in a bonded magnet as it is realized in the SmCo5 bonded magnet. On the other hand, sintering is difficult because it will be decomposed into samarium nitride and a-Fe when heating it up to 500°C:"

Jan 1, 2000

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By Eren Hüseyin Obuz

In this study, the leaching kinetics of rare-earth elements were investigated using HCl and HNO3 solutions. A standard crushed complex ore was utilized as raw material. The complex ore (particle size of under 54 μm) contains REE (Ce, La, Nd, Pr, etc.). Different leaching durations were selected for the kinetic studies. The highest leaching efficiency was obtained in HCl solution, and the leaching mechanism was identified to diffusion through a product layer. The rate constants of Ce, La, Nd, and Pr were calculated as 1.08 × 10−2, 0.86 × 10−2, 1.87 × 10−2, and 1.34 × 10−2 h−1, respectively.

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

The effects of microwave roasting on separation of rhenium (Re) and molybdenum (Mo) from a molybdenite concentrate have been investigated based on evaluation of the heating characteristics of the concentrate in the microwave field. The results show that a variety of operating variables, namely microwave power, sample weight, sample geometry, roasting temperature, roasting time and atmosphere significantly impact on the volatilization rates of Re and Mo. The optimum conditions for Re-Mo separation are microwave power 1300 W, sample weight 20 g, sample geometry pellets, temperature 600 oC, time 1.5 h, and atmosphere 20%O2. Under these experimental conditions, the volatilization rate of Re reaches 88.12%, while that of Mo is just 5.15%. Microwave-assisted roasting provides an alternative route to separating Re and Mo from molybdenite concentrate.

Jan 1, 2016

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Chonghe Li, Xionggang Lu, Wei Xiao, Xingli Zou, Weizhong Ding

The reduction degree and rate of the initial ilmenite concentrate and pre-oxidation samples by hydrogen were investigated by using thermogravimetric analysis system. H2-TPR was used to detected reduction properties of the pre-oxidation products which were oxidized at different temperatures. The phase transformations and micromorphology changes during pre-oxidation and hydrogen reduction were identified by XRD and SEM. The FeTiO3 was decomposed into TiO2 and Fe2O3 at the temperature below 900 oC. With the temperature rising, Fe2TiO5 was the only stable phase in high temperatures. The reduction of pre-oxidation ilmenite concentrate was faster than the natural sample, which was attributed to the micropores generated on the surface of ilmenite concentrate during oxidation. The main phases of the reduction product were metallic iron, ferrous pseuodbrookite.

Jan 1, 2014

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Aïda Espinola

Decontamination of synthetic solutions containing cadmium ions using coconut fibers in natura was investigated in laboratory scale. Cadmium ions, a serious pollutant of water ways, where it is detrimental to the environment, may be absorbed by fish and mollusk used as food, which will, eventually, poison humans; these ions are usually present in minero-metallurgical and electroplating industrial effluents. Usually employed for the aqueous effluents treatment are chemical precipitation, adsorption and electrolytic processes. Precipitation is not effective for cadmium removal, because of the high KpS of the cadmium hydroxide, which requires high pH; only sulfide would be efficient in cases of very small amounts. Some vegetal refuses have shown to be practical for absorption processes of several metallic ions. We have applied coconut (Cocos nucifera) shells, which are extremely abundant over most of the extensive Brazilian coast, in the removal of cadmium: it has been verified, in our laboratory, that the surface of the fiber of this coconut is rich in chemical compounds which are active scavengers for Cd2+. For the optimization of the process, hydrosoluble components existing on the surface of the fiber, which may be deleterious, were previously washed out by water, and variables, such as the pH and the proportion of mass of fiber to volume of solution, were adjusted. As much as 99% of the initial contaminant metallic ion has been eliminated, resulting a solution to be discarded which contains ca. 0.1 ppm; this attends to the maximum impurity legally admitted by the environmental control agency of Rio de Janeiro, FEEMA, for cadmium ions in aqueous effluents to be disposed in rivers and in the Guanabara Bay area.

Jan 1, 1998

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

By Chuanfu Zhang

Based on Thermogravimetric and Differential thermal analysis (TGA-DTA), porous copper powder is prepared by thermal decomposition of complicated copper oxalate. The effects of various conditions on the morphology, crystalline grain size and specific surface area of copper powder were investigated, including temperature, duration, mixing ratio of nitrogen and hydrogen. Furthermore, composition and morphologies of the products were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM) and BET adsorption isotherm. It is found that porous copper powder was produced under optimum conditions. The specific surface area is over 6.74 m2?g-1, and average pore size in particles is about 30.3 nm. After comparison of SEM images, the final product Cu well inherits the morphology of the precursor, thus a mechanism of in-situ decomposition is proposed.

Jan 1, 2009

By Zhao wen Wang, Ramana G. Reddy, Min Li

"The electroreduction of Co(II) in l-butyl-3-methylimidazolium tetrafluoroborate (BMlMBF4) ionic liquid was investigated by cyclic volatrnmetry at 353 K. The results show that the reaction of Co(II) to Co is irreversible in one step with two electrons transferred. The diffusion coefficient of Co(II) was estimated to be 7.6 x 10-8 cm2 s·1 at 353 K. Then the electrodeposition of cobalt was studied at different cathodic potentials (-0.80 to -0.95 V) and different temperatures (333 to 363 K) in BMIMBF 4 containing 0.20 mol L-1 Co(BF4)z. The deposits were characterized using scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD). SEM images show that a uniform, dense, and compact deposit was obtained at -0.80 V and 333 K. The deposits were identified as high-purity metallic Co for all experiments by EDS and XRD.IntroductionCobalt is known as a hard magnetic material and cobalt alloys have been shown to have excellent magnetic properties with adequate mechanical durability and corrosion resistance, which are needed for high performance magnetic recording applications [1-4]. The electrodeposition of Co alloy in the aqueous solution is generally difficult because of the narrow electrochemical potential window of water, which leads to the low current efficiency and worse quality of deposits due to the hydrogen embrittlement. Thus, aprotic ionic liquids (ILs) are expected to be the ideal alternative media for electrodeposition of cobalt or its alloy since ILs usually provide a wide working potential windows, negligible vapor pressure, and acceptable conductivity for electrolysis without the occurring of hydrogen evolution [5, 6]."

Jan 1, 2014

By U .. C. Rojas, J .. C. Gomez

"Fire Refined Copper (EI Teniente Three Stars) has been produced at Caletones Smelter of Codelco Chile since almost the beginning of its operations.Due to changing features of the copper market, together with the targets on technical efficiency and productivity, it has become more and more relevant for copper industry to reach both, good final product quality and a proper environmental control.At present, copper refining process at Caletones Smelter takes place in two cylindrical tilting furnaces, where solid fluxes are injected through horizontal tuyeres into the molten bath. (Fig. N2 1)Solid reagents are pneumatically conveyed and injected into the liquid copper bath attaining excellent solid - liquid contact, so the impurities removal efficiencies are found to be high. Same injection tuyeres are used to introduce both oxidising agent (normal air) and reducing agent (reformed gas) into the molten bath. Air or nitrogen is used as conveying gas for solid reagents, depending on the process stage.This pap~r gives a fundamental description of the process and industrial results related to the injection of blend of sodium and calcium carbonates to remove arsenic and antimony, silica and granulated reverberatory slag to remove lead and a mixture of calcium carbonate and mineral coal to reduce the selenium content of the fire refined copper."

Jan 1, 1996

By Wang Jia, Chai Li-yuan, Zhang Jin-Long, Peng Bing, Zhang Qiang

"Electrolytic manganese dioxide (EMD) residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick for the utilization of the residue from EMD production. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity. The results showed that the calcined residue had capability of solidifying toxic metals and exhibited perfect strength after treated in the optimal parameters of EMD residue below 50%, temperature at 1000-1100°C, time3-5h, and semi-quenched at 600°C1 InstructionSolid clay-brick holds the leading position among building materials for a very long time in China. The traditional technique of making clay-brick has the drawbacks of backward process, simple facilities and single product. Since Chinese Reform and Opening-up, urban-rural construction and real estate have been booming with the rapidly development of national economy and science technology. The problems of ruining fertile land, environment contamination and high energy consumption in the traditional technique of clay-brick making have not been solved yet. On the other hand, more than 7 billion tons of industrial wastes are accumulated over years which occupies over 6.7 million hectares filed and causes serious environmental problems[1-31. Strategy present in ""The Chinese Agenda of the 21st Century"" required the production of wall materials less energy conservation, land saving and waste recycling.Coal gangue[4-9l, fly ash[I0- 13l, sludge from waste water treatment and tailings of gypsum, pyrite, copper mine, high silicon containing iron, asbestos and ects [l4-lSJ are the solid wastes used for brick making around the world. There are two kinds of process for brick making, high temperature sintering and low temperature steam curing[19•201. Although the technology of two brick making made great progress and got widely application in construction field, no precedent for preparing sintering-bricks with EMD residue as materials occurred in China because of its complicated processing technics and lack of sufficient practical experience to guarantee the bricks' quality.In this study, EMD residue was mixed with shale and fly ash as the main materials to make solidification/sintering brick. The effects of sintering temperature, sintering time, solid waste content and cooling process on its mechanical properties and toxic elements solidification were investigated according to compressive strength and leaching toxicity."

Jan 1, 2011

By Ting Lei, Mingjun Rao, Guanghui Li, Tao Jiang

"With the rapid development of iron and steel industry, the supply of iron ores can not meet the present demand for iron and steel industry in China. Large reserves of oolitic hematite have been discovered with low iron grade (30% ~ 45%) and high phosphorus content (0.4% ~ 1.8%). Traditional processes for utilization of this ore are characterized as either high cost or low dephosphorization. In this study, sodium salts-modified paigeite (SSMP) was added to enhance on the dephosphorization of high-phosphorus oolitic hematite by using reduction roasting followed by magnetic separation. Various parameters, including the amount of SSMP, reduction time,reduction temperature, grinding fineness and the magnetic field intensity were investigated. As a consequence, a magnetic concentrate of metallic iron powder with total iron grade of 93.2% and phosphorus content of 0.08% was obtained under the optimal conditions. The results also provide a potential avenue for the comprehensive utilization of paigeite ore.IntroductionOolitic hematite is currently recognized as one of the most refractory iron ore resources in the world. Over 4.0 billion tons of reserves of such resources have been found in China, and more than 10 billion tons in the long-term. This kind of ore is characterized as low iron grade (30%~45% TFe) and high phosphorus content (0.4%~1.8% P), as well as fine particle size distribution of ferrous minerals (the size distribution varies from 5~30 µm, even less than 2 µm) and the complex association between iron and other gangue elements [1~5]. The unique structural characteristics of the high phosphorus oolitic hematite make it difficult to obtain high iron recovery and good dephosphorization efficiency by using the conventional processes [1,2]. Traditional processes are characterized as high cost and low dephosphorization for oolitic hematite beneficiation [9~15]."

Jan 1, 2012

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996