Search Documents

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed_ This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels_ Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By Moenster J. A., M. J. Sankovitch

Doe Run's Buick Smelter was converted from a primary lead smelter to a secondary lead smelter in 1991. The recycling facility was designed to produce 60,000 tons of refined lead per year from 110,000 tons of spent starting-lighting-ignition (SLI) batteries and 10,000 tons of lead contained in drosses and scrap. Since commissioning, Buick's refined lead output has steadily increased to exceed 120,000 tons for 1999. The production gains have been the result of continuous process improvements, empowerment of the workforee, and development of additional scrap lead streams. The production gains were accomplished while setting industry standards for employee safety, reducing plant environmental emissions and employee blood leads, achieving ISO 9002 certification, and expanding product lines to meet customer requirements. This paper highlights Buick's major accomplishments through the 1990's.

Jan 1, 2000

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4T13O12 (BIT) which has a positive temperature coefficient of dielectric constant (TE) can be used to modify the negative of typical microwave dielectric ceramic BaNd2Ti4O12(BMT). However, BaNd2Ti4O12/Bi4Ti3O12/BaNd1Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C was much higher than that of Bi4Ti3O12 ceramic (around /1100°C). in this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated divided proposed to prepare ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second mop, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti1O12 ceramic pellets and spark plasma sintered at 900'C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe mircoanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/B1T/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.8, a low dielectric loss of 0.0068 and a small temperature coefficient of dielectric constant v/35 ppm/C at 1 MHz.

Jan 1, 2003

By Philip L. LeHoux

"Kennecott Barneys Canyon Mining Co. is a gold heap leaching facility that has been in operation since 1989. In 1994, a flotation plant was commissioned to remove sulphide minerals from refractory sulphide ore. Tailings from the plant are mixed with oxide heap leach material in order to produce a geotechnically stable agglomerate from which the gold is leached and recovered in a conventional heap leach cyanidation process. The experience to arrive at an effective blending methodology is discussed.IntroductionAgglomeration is the practice of binding fine particles to coarser rock or other fines in order to avoid the deleterious effects of mobilizing the fines during the course of heap leaching(l-Chamberlin). Agglomeration has been considered a key component of successful operation at many heap leach sites. If the ore is of sedimentary origin and crushed, there is a high likelihood that the resulting product will contain a significant quantity of fines and a skewed gradation, that i~, a disproportionate amount of coarse and fine particles, with few in the intermediate size range. The exact methodology for determining whether the practice of agglomeration will have to be integrated into the operating scheme has been well discussed. These conditions are primarily geotechnical and geochemical. This paper will deal with the specific experiences of Kennecott Barneys Canyon Mining Company in modifying the agglomeration practices to suit evolving operational requirements."

Jan 1, 1997

By Dean G. Heitt

"The Rain and SMZ mines from 1987 to 1994 produced a total of22.0 t of gold from a pre-mine reserve of 14.24 Mt of ore grading 2.13 g/t Au.Gold at Rain is hosted within the basal portion of the Mississippian Webb Formation. ·Mineralization is closely tied to the Rain Fault which is interpreted to be the main feeder for the deposit. Multiple collapse and hydrothermal breccia events provided permeability for the mineralizing fluids in the otherwise unreactive siltstones. Major alteration events include: decalcification and dolomitization of the Devils Gate Limestone; and silicification, baritization, argillization and oxidation of the Webb Fm. Six ore types based on XRD and visual rock chip Jogging have been identified: siliceous ore containing >40% quartz and <30% barite; siliceous-baritic ore containing mostly silica but >30% barite; baritic ore containing >40% barite; argillaceous ore containing >40% total clays (including alunite); calcareous ore containing mostly calcite and dolomite; and carbonaceous ore which has significant pyrite and organic carbon. Metallurgical testing of the oxide leach grade ores found that recoveries, on -1.3 cm crushed material, were greater than 70%. Results also found that Rain ore has strong grind dependency due to silica encapsulation.The Rain leach pad was commissioned in 1988, and to date 9.3·Mt at an average grade of0.65 g/t Au have been placed. Life to date recovery, through December 1995, is approximately 51 %, for a total of3.87 t of gold produced. Two major factors have contributed to the low leach recoveries at Rain when compared with the metallurgical testing: 1) More argillaceous ore than expected was placed on the pad especially late in the mine life and 2) approximately 50% of the tons placed were run-of-mine with no agglomeration."

Jan 1, 1997

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988

By S. J. Hogan, T. William

"By the year 2000, the steel industry, not only in the United States but in the rest of the world, will undergo significant changes. On the other hand, there will be a number of areas in which change will be minimal.The current capacity of the industry worldwide is approximately 800-810 million metric tons. This may grow to some extent, as Third World countries install capacity. However, much of it will be neutralized as the industrialized countries shrink their current capacities.There will be several breakthroughs in terms of technology, some of which deal with the production of iron outside of the blast furnace. However, these processes will not be far enough advanced by that time to replace the blast furnace, rather they will supplement it.In terms of steelmaking and the subsequent rolling process, there should be a number of basic improvements. The strip mills will roll sheets with a very slight variance in gauge, which will give the customers a better product for automatic stamping machines. Ordinary carbon steel, in a number of instances, will be replaced by high-strength, low-alloy steel, which will reduce the tonnage necessary for present-day applications, such as construction.The corporate organization will be significantly changed as joint ventures and mergers will reduce the number of companies, as well as facilities in operation. This will enable the industry to reduce its capital investment and improve operating costs, so that it will be able more effectively to compete with other materials, such as plastics, cement, aluminum, etc."

Jan 1, 1988

By J. Boltano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Codelco-Chile. A discussion on design conditions for a future Sulphuric Acid Plant using Teniente Converter gases is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited gas handling capacity for operation under future process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente Converters Installed in 1987-1989 improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By J. Boitano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Cbdelco..Chile. A discussion on design conditions for a Mure Sulphuric Acid Plant using Teniente Converter.gases.is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited .gas handling capacity for operation under Mure process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente converters installed in 1987-1989 Improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft&apos;s Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Ignacy A. Lipiec

The advantage of microorganisms used in bioleach systems to conventional chemical reaction systems is that these apply the available energy more precisely where it is needed, either directly onto the mineral of interest or by efficiently catalyzing the production of a reactant. The literature cover the range from empirical models used in describing macro heat balance in heaps to detailed studies relating the micro heat effects of bacteria adhesion energy to the surface of minerals. In this paper, the heat effects are reviewed in a general way describing bioleaching in two macro systems, heap leaching and slurry bioreactors. The micro scale heat effects is the reactions and conditions at the microorganism scale, including the mechanism of leaching and bacterial behavior.

Jan 1, 1998

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.