Search Documents

By Thomas M. Brady

The Spokane Research Laboratory/NIOSH and the University of British Columbia (UBC) geomechanics group are focusing on the development of safe and cost-effective underground design guidelines for weak rock masses having an RMR in the range of 15 to 45. Weak ground conditions, ground support, and mining methods used in several North American underground mines were observed. The RMR values were calculated to update both manned entry span design and non-entry stability graphs, plus a database on underhand mining methods was created to reflect existing North American mining conditions. The immediate rock mass was characterized and analyzed in terms of prevailing type of ground support, potential failure mechanisms, and rock behavior to define how existing design curves must be modified for the existing weak rock mass. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making sound economic decisions that will also ensure a safe working environment.

Jan 1, 2006

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Stephen C. Tadolini

The U.S. Bureau of Mines, in cooperation with the Cyprus- Plateau Mining Company, has conducted research to provide an alternative to traditional secondary support systems in a two-entry, yield pillar gate road. As recent as two years ago, it was impossible to imagine a gate road supported solely with internal high-strength resin-grouted cable supports that would virtually eliminate the necessity for crib or concrete external supports. The support system evaluated consisted of 1.6-m (5-ft) full-column resin-grouted bolts and 4.8-m (164) long cable supports installed in conjunction with wire mesh and "monster-mats." Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during first and second panel extractions. The stress and loading histories for the panels and yield pillar were monitored to evaluate the stress transfer and pillar performance in conjunction with the roof and floor behavior. The test results indicated that the designed support system successfully maintained the roof during the extraction of two longwall panels and dramatically reduced the cost of secondary support. This paper will describe the theory of a cribless support system, the advantages of cable supports, and present the pillar, roof, and floor measurements made to assess the support performance during longwall retreat mining.

Jan 1, 1995

By Adrian L. Moodie

Austar Coal Mine (formerly Southlands and Ellalong Collieries) has had a long association with difficult strata control conditions associated with mining depth and a highly jointed/cleated coal seam. The conditions include poor longwall face conditions, cyclic loading, heavy tailgate (TG) roadway conditions, and difficulties in maintaining stable roadways on development at 5.2 m (17 ft), as well as the geotechnical challenges of an 8.5-m (27.9 ft) -wide roadway required for installation faces. The introduction of Longwall Top Coal Caving (LTCC) to this environment has aided in the management of some of these issues, but LTCC has also given rise to other geotechnical considerations. Additional geotechnical issues associated with LTCC not only require management during operations, but also require consideration when evaluating new mining areas at Austar Coal Mine or potential LTCC extractable resources throughout Australia and the world. In September 2006, LTCC commenced at Austar Coal Mine in longwall panel A1. Since this point the LTCC face has been increased from 147 to 216 m (482 to 709 ft)and finally to 227 m (745 ft) in width, and it has also been rehanded and modified in the three fully extracted panels to date. The application of LTCC in panels A1, A2, A3, and now A4 has been very successful, both from a coal resource recovery point of view and in the management of the principal hazards of spontaneous combustion and strata control. This paper focuses on the geotechnical aspects of the application of LTCC at Austar Coal Mine and also reviews some advances in general strata control management at the mine.

Jan 1, 2011

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By Daniel Su

This paper describes recent ground control challenges encountered at the longwall recovery areas of one of Bailey Mine?s two longwall faces and the proactive measures taken by CONSOL management and engineering to mitigate them. The challenges derived primarily from the following causes: (1) irregular roof coal and draw slate thickness, (2) presence of thick sandstone at the recovery area and extremely weak rocks below the sandstone, (3) close proximity to a regional anticline, (4) low shield set pressure and tip load, and (5) ineffective primary roof support that led to progressive failure of the headgate roof. The presence of the anticline contributed to extensive fracturing of the sandstone. Excessive pot-out in advance of the shields frequently occurred near mid-face due to the presence of thick draw slate and irregular roof coal near the recovery area. This, in turn, resulted in face heights that exceeded the maximum reach of the shields. Subsequently, during longwall meshing, when the advance rate slowed considerably, fractured sandstone would often break loose, causing the shields to yield, thereby reducing the height and inhibiting shearer movement. To improve the headgate and face conditions within the longwall recovery area, several actions were taken, including: (1) assessing site-specific roof geology by conducting in-mine roof coring around the recovery areas and by mapping immediate draw slate and roof coal thicknesses within surrounding entries, (2) increasing pump pressure and thus shield set pressures (3) diligently monitoring shield set pressures and longwall extraction horizon, (4) installing additional cable bolts and roof screening to prevent progressive failure of the immediate headgate roof, (5) fully-grouting supplemental cable bolts to improve headgate support stiffness, and (6) gluing the headgate roof within the recovery areas with polyurethane. As a result of these collective efforts, longwall recovery delays at Bailey Mine were reduced from 21 days in 2006 to nearly zero in 2009.

Jan 1, 2009

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By J. C. Johnson

High-grade ore found in a shaft pillar at the Homestake Mine prompted a request for a Bureau of Mines study to determine if selected areas of the shaft pillar could be mined without jeopardizing the shaft. The design approach was to perform a finite-element study of the shaft pillar. Plan view and vertical sections were developed using two-dimensional, elastic, plane strain assumptions. Input into the model consisted of in situ stress measurements geologic mapping rock mass properties, and previous mining history. Results from the study indicated that ore-beating sections of the shaft pillar could be removed within the displacement tolerances acceptable for the shaft. Homestake engineers, using the results of the finite-element study and considering other factors, have designed and are beginning to mine the shaft pillar.

Jan 1, 1989

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986

By E. C. Westman

Anomalous geologic or stress-induced conditions can create a hazardous working environment for underground miners. Seismic attenuation tomography provides a valuable tool for understanding static and dynamic conditions induced by mining. As a longwall shearer cuts coal, it generates seismic energy. As this energy travels through the rock mass it is attenuated in a manner proportional to the degree of fracturing of the rock mass. By calculating this attenuation at specific locations underground, the degree of fracturing of the rock mass, and hence the relative stress state or material properties can be inferred. The goal of this work has been to create a tool which can be easily used by the mining industry to obtain information about the distribution of stress concentrations or material properties across a broad area in advance of mining.

Jan 1, 1996

By Andrew G. Martin

In 1991, Modular Mining Systems began marketing a Slope Monitoring System (SMS) now installed at twelve mines. The SMS uses automated wire line extensometers to monitor field conditions frequently. Every few minutes, the slope displacement values and current temperature are transmitted to a central computer via a packet radio telemetry system. The desktop workstation receiving the data continuously provides updated displays of active slope monitors and generates audible and visual alarms if movement exceeds user specified thresholds. The computer system also generates numerous graphs and reports for quick analysis of slope stability. This work describes the functionality of the SMS, details improvements to the SMS hardware and software developed for several clients, outlines different installation techniques needed for wall rock and spoil monitoring, and interprets slope movement data using illustrations of stable and unstable conditions.

Jan 1, 1996

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989