Search Documents

By R. L. Machunda, A. M. Rugaika, D. D. Mdachi

Sedimentary and igneous rocks are the two primary sources of phosphate that are mined and beneficiated to fertilizer. During the beneficiation process, phosphate is lost into the tailings. We investigated phosphate concentrations in tailings dumps at Minjingu mine, Tanzania using energy-dispersive X-ray fluorescence spectrometry to quantify the chemical compositions. The phosphate content in the tailings varied from 12.91% phosphorus pentoxide (P2O5) in Tailings 2 to 19.61% in Tailings Dump 1. The naturally occurring phosphate concentration in rocks ranges from 3% to 35%, and phosphate tailings from various locations with P2O5 concentrations as low as 6.46-12.65% have been beneficiated to commercial fertilizer. Our investigation revealed that phosphate concentrations in Minjingu tailings may be sufficient to be recovered for commercial applications. Suitable recovery methods are discussed, and we recommend that beneficiation should be performed to minimize the loss of phosphate into tailings. Further research is needed to identify the optimal beneficiation methodology.

Aug 8, 2024

By Lutz Markworth, Wolfram Jaspers, Johannes Kottmann

PNEUFLOT® technology has been applied for the past 20 years in coal, ore and other minerals processing plants. During the last two years this technology has achieved a breakthrough with some 42 units being sold signifying a rising trend. »Humboldt Wedag Coal & Minerals Technology« has performed extensive research and development work over the last five years. The results of which were used to design a new fourth generation aerator. Humboldt Wedag, through its association with EKOF, can offer a holistic solution encompassing both flotation equipment and reagents. It is the only company in the world able to offer such a package. The association with EKOF strengthens the Humboldt Wedag product offering, especially as the company in-troduced pneumatic flotation cells to the South African market in the form of the PNEUFLOT®. Before starting pilot scale test work, a mineralogical analysis has to be carried out to determine the mineral com-position as well as the liberation grade. HW-CMT works together with independent institutes. Different reagent regimes can be tested in laboratory scale. Pilot machines, each packed in a 20? container, are available to carry out extensive test work at customers? processing plants. A group of engineers from HW-CMT is involved in the pilot test work. The flexible pilot machines are designed to cater for coal, ores and other minerals. The small feed rates of 7 ? 12 m³/h only means the pilot machines do not disturb the operation of process plants. Batch tests have to be carried out to determine the numbers of PNEU-FLOT® stages. New applications in iron ore, copper ore, platinum group minerals, rock phosphate and potash were suc-cessfully tested in the last three years. In applications where the feed material is very fine, PNEUFLOT® technology is able to achieve high recoveries with particle sizes where conventional technology failed.

Jan 1, 2007

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By P. Foster

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident reconstruction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed, namely (i) remote control continuous miner operation and (ii) free steered vehicle sight-lines, which demonstrate the practical use of VR in this area.

Jan 1, 2004

By John E. Leitch

The cost of corrosion as measured by such cost components as the renovation or replacement of coated steel, or the use of expensive coating systems on steel, is considerable. Extrapolating from figures for the USA would place the overall cost of corrosion for South Africa as a figure of the order of magnitude of something over 1% of the GNP. This is a sizeable amount, of which costs associated with atmospheric corrosion would be a significant proportion. The corrosivity of an atmosphere can be defined as the ability of the atmosphere to cause corrosion in a given metal or alloy (International Standards Organization [1]). The ISO Standard 9223 specifies the key factors in the atmospheric corrosion of metals and alloys, and defines categories of corrosivity on the basis of these factors. Prior to the publication of that ISO standard, Callaghan published the results of his twenty-year exposure programme and his excellent corrosivity map of Southern Africa [2]. The present author published updates of the corrosivity map in 1999 [3] and again in 2003 [4]. The summary of the individual areas of corrosivity around Southern Africa was published in the latter paper, and is reproduced here as the following TABLE 1. Of significance in TABLE 1 are the numerous regions of very high corrosivity (C5 or beyond), particularly the rural West Coast shoreline, the North East Coast (KZN) shoreline, and the coastal cities Cape Town, Durban and Richards Bay. The corrosivity map as published is obviously based on much extrapolation as only a small number of points have been measured. During the past three years further measurements have been made, mostly however at the same sites in order to give greater reliability and to monitor long-term trends with changes in pollution. These two aspects are incorporated in this update. There has become available a greater amount of air pollution data for centres in South Africa than was the case some years ago. In this present paper the pollution data are used to extrapolate the corrosivity over areas where little or no direct corrosivity measurement has been made. This methodology is described in ISO 9223.

Jan 1, 2006

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By S. J. Frank

Ferroalloy furnaces are well known to be extremely difficult to control from a metallurgical perspective. Mostly metallurgical control is still reactive in nature, causing a significant amount of reworking and product blending to achieve a proper product specification. Despite numerous efforts towards the model based control of primary smelting operations, actual metallurgical feed forward control seems to remain elusive. One of the key reasons in the failure to model these metallurgical reactors well, is that fundamentally orientated pyrometallurgists, statisticians, data miners and control engineers very often have diverging ideas how to model these systems. Furthermore, metallurgists have often come to rely on their ability to develop empirical regression models of furnace behaviour, as they have lost their faith in the ability of thermochemical and metallurgical engineering fundamentals to accurately predict the outcomes from furnaces. This paper shows how good thermochemical modelling can be combined with proper technological and systems analysis, as well as a proper inventory model, to predict the alloy and slag chemistry with good accuracy one tap into the future, at a time horizon of typically around 4 to 6 hours. For this modelling approach, a number of tools will be used, such as data reconciliation, thermodynamic modelling using Fact Sage®, inventory and heel estimation, neural networks and statistical data exploration. Furthermore, systems identification theory will be combined with the approaches given above to develop a truly dynamic predictive model. This paper seeks to demonstrate the need for a hybrid approach, which incorporates plant data and readily accessible thermodynamic data to develop a proper dynamic model.

Jan 1, 2004

By Steven M. Rupprecht

"The artisanal mining sector in Central Africa is largely informal, yet provides an essential livelihood for many (directly or indirectly) participants, as well as facilitating an important source for the flow of income into many communities. Artisanal mining varies from site to site, but appear largely well structured despite its informality. The artisanal mining sites in Central Africa have some inherent management structure and the extraction itself is often organised. Artisanal mining is labour intensive and is generally conducted utilising hand digging methods e.g. shovels or hand chisels. Artisanal mining is generally more dangerous than small-scale or large-scale modern mining operations. This is especially true as artisanal operations are generally subsistence activities with artisanal miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. The objective, through proper/dedicated training of artisanal miners is to migrate Artisanal mining to establish a small-scale mining (SSM) industry in Central Africa. Through developing the necessary skills in the fundamental areas of mining it is proposed that Artisanal Mining can become more productive and safer mining operations. The paper reviews the above focus areas, highlighting the skills and tools that are necessary to assist in establishing a sustainable small scale mining industry migrating from manual labour to semi-mechanised mining and processing. The purpose of the transformation process is to create a safe, healthy, environmental and community oriented mining operation with the objective to uplift the skills and wealth of the mineworkers and the general community."

Jan 1, 2015

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By S. Montes

Mineral floatability is strongly connected with mineral structure and composition. The complexity of mineral surfaces has meant that few attempts have been made to understand the effect of impurities (trace elements) on the flotation process. Zeta potential technique has been extensively used to evaluate the surface charge of mineral particles. Nevertheless, those measurements consider only an average of mineral particles surface charge. The presence of fine particles and inclusions covering a mineral may influence the local reagent adsorption process, which will ultimately be reflected in the subsequent global response of the mineral froth flotation efficiency. The current work assesses the iron oxide mineral, haematite (Fe2O3). Zeta potential and streaming potential techniques were used to determine the surface charge of fine and coarser particles of haematite. Further analysis was performed to determine the point of zero charge (PZC) of the mineral. In addition, adsorption isotherms of alkyl ammonium chloride reagents with different lengths of carbon chains were carried out. It was found haematite floatability depends strongly on the isoelectric point (IEP) value, which is affected by other mineral species present at the mineral surface. Haematite floatability became significant only at relatively high tetradecyl ammonium chloride collector concentrations (concentration greater than 4 10-4M), which does not happen with other oxides such as quartz. Unlike quartz, haematite develops a low surface charge over a wide range of pH, disabling all long-range attractive interactions between the mineral and the collector. Therefore, hydrophobic chain interaction is probably the most likely mechanism acting to promote collector adsorption and enhance further floatability. Diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to suggest a possible mechanism to understand the sequence of collector adsorption and the effect of trace species on it. Keywords: floatability, haematite, adsorption, electrochemistry, zeta potential.

Jan 1, 2007

Despite the wealth of information available on phase equilibria of oxide systems there remainmany gaps and inconsistencies in our knowledge base. From an industry perspective there is anongoing need to adequately describe the phase chemistry of slag systems in order to optimizeprocess performance and improve productivity. Since this chemical behaviour cannot be predictedfrom first principles it follows there is also an ongoing need for accurate experimental data. The advances made in recent years in the capabilities of sophisticated analytical and measurement equipment have made it possible to develop new experimental techniques for the direct determination of phase equilibria in low order and complex multi-component slag systems. In addition the development of powerful computer modelling tools makes it possible to provide more comprehensive descriptions of the phase chemistry, to present the information in a range of perspectives, and to critically analyse the various types of related thermodynamic and structural information available. This review provides an overview of the types of information that can be used to determine phase equilibria in slags systems, analyses the influence of uncertainty and the relative importance of these types of data, and describes the advantages and limitations of the various experimental techniques that can be employed to obtain this information. Examples of recent studies are provided that demonstrate how an integrated approach to the determination of phase equilibria in complex systems, involving the use of targeted experimental studies and systematic thermodynamic model development, can lead to a better utilization of our current research capabilities and resources and more accurate descriptions of these systems. Keywords: slags, phase equilibria, experimental techniques

Jan 1, 2004

By T. Güyagüler, A. Güngör

Labour protection, that is prevention of occupational disease and reduction in the frequency of accident, has always been a matter of major concern of mining industry. Management and the government should promote and maintain high safety standards through some measures to reduce accident frequency and occupational disease. This can be achieved by using the science and technology for improving the working conditions, educating workers and managers about accidents and prevention techniques. The detailed analysis of an accident requires knowledge of many factors such as location, time, type, cost of accident, victim, nature of the injury, personal and environmental factors etc. that can be obtained from the standard coded accident report form. There is a need to prepare safety data in a common format to produce a common safety reporting system and ‘Occupational Health and Safety Management Tool’ is being designed to manage this by using database and Internet technology. Precautions should be taken according to results from database queries by providing comprehensive and accurate national data. To have an accident is unfortunate, however, to have an accident and learn nothing from it is unforgivable. Keywords: Occupational health and safety, Accident report form, Accident database, Occupational diseases and accidents, Safety reporting system.

Jan 1, 2003

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007