Search Documents

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004

By D. Norval, J. J. Dunkley

The process of atomisation is introduced and related to granulation. Some processes applicable to ferroalloys are discussed, along with their limitations and advantages. Examples of applications of atomisation to the processing of ferroalloys, including ferrosilicon and ferromanganese for use in the welding industry and as injectable additions to steel or cast iron are also presented. The economics of the process and the impact of process scale are discussed, along with criteria for process selection and system design.

Jan 1, 2004

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 357 to 366 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2002 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 26 July 2002 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2002 set out on page 357 to 366 wereapproved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2002

By K. R. P. Petersen

Paper written on project work carried out in partial fulfilment of M.Sc. Eng.(Metallurgical Engineering) degree The interrelationship between mineral liberation and leaching behaviour of a gold ore is ill defined, mainly due to the complexity of both leaching and mineral liberation. This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organizing neural net, which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 8.1%). Moreover, the self-organizing maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2003

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By C. Daly

The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course, ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course ? the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks. The term ?peer assessment? in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ?try and see? approach. Each student must describe in detail the process they undertook to achieve their final design ? hence the approach is independent of the discipline and/or project selected. Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ?run? is for feedback only during week six and hence no moderation is undertaken. It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students. Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks.

Jan 1, 2014

By C. Daly

"The Faculty of Engineering at the University of New South Wales (UNSW) offers a core first-year engineering design and innovation course,ENGG1000, undertaken during the first and second semesters. This course is highly regarded in the sense that it provides an introduction to many concepts and activities that students will experience over the four-year minimum for which they are undergraduates at UNSW. Approximately 1400 students enrol in the semester 1 course across the Faculty, typically 80 of which undertake the Mining Engineering stream. Students in teams of between six and eight design and construct a physical model to represent an aspect of their chosen discipline. For example, in 2013 the mining engineers designed and built a model dragline. This paper concentrates a major aspect of the course - the involvement of team members in group activities and the development of the associated skills of peer assessment and peer review as the course progresses over a period of 12 weeks.The term ‘peer assessment’ in this paper refers to the requirement for students to assess the design components of their peers. This course has a structured requirement in terms of how a successful design is a result of a sound design process rather than a ‘try and see’ approach. Each student must describe in detail the process they undertook to achieve their final design - hence the approach is independent of the discipline and/or project selected.Peer review is a process whereby students review the contribution of their team members to the overall design. This activity encourages team involvement and interaction. The final assessment mark can be moderated by the outcome of this peer review, although it is run twice during the semester. The first ‘run’ is for feedback only during week six and hence no moderation is undertaken.It was found through consultation with students and from questionnaires that both processes are well accepted and highly regarded by students, as they give them a degree of ownership of the assessment process. In addition, the processes provide rapid and relevant feedback on the progress of individual students.Peer review and peer assessment are also considered to be very valuable tools for use in courses in succeeding years. For instance, many of the courses in mining engineering rely heavily on group assessment tasks."

Jan 1, 2014

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By P. J. Bhonde, R. D. Angal

Conventionally low carbon ferromanganese is manufactured globally by refining high carbon ferromanganese in liquid state. This process is an expensive and lengthy technique. Hence, the present work was undertaken with the objective of understanding the feasibility and kinetics of the solid state refining of ferromanganese. The process involved transformation of carbon rich carbides viz. Mn3C2, Mn7C3 into metal rich carbide i.e. Mn15C4, Mn23C6 by subjecting the alloy powder to a flowing stream of carbon dioxide. Effect of the process governing parameters such as time, temperature, particle size, pressure on the extent of decarburization was studied. Without any loss of manganese in the form of fumes or slag, it was observed that, there was substantial reduction, viz. 65 per cent in the total carbon content, by this technique. Subsequently, the process was investigated to find out the mechanism of carbon removal. Depending upon the temperature and the particle size, it was found that the rate controlling mechanism changes from chemical reaction control to product layer (ash) diffusion control. The activation energy for each of the aforesaid mechanism was computed. The values thus obtained substantiated the aforesaid mechanisms.

Jan 1, 2004

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By S. Badr, R. Mendoza, M. U. Ozbay, M. D. G. Salamon

ABSTRACT: The use of coal pillars at depth is fraught with problems due roof control difficulties and the possible occurrence of coal or pillar bumps. In the USA the largest and most important application of pillars at depth is in longwalling, where chain pillars are the customary supports of the multiple entry developments. At first, the chain pillars were designed using conventional approaches, where the principle is that the strength of the pillar should exceed the load imposed on it. Such approach to design led to larger and larger pillars at great depths, but instead of eliminating, it tended to aggravate the roof control problems. Eventually the idea was born that small sized yielding pillars, which have proved to be successful elsewhere, might provide the answer to this pressing problem as well. The aim of this paper is to study the modes of pillar failure at great depths, using two solution methods. The first of these comprises some elementary solutions obtained with the aid of a simplified conceptualization of the rock mass. This model consists of a strain-softening coal seam sandwiched between two stratified masses. The second approach utilizes FLAC3D, which is a commercially available three-dimensional numerical modeling software package. To gain a better insight, both the strain-softening and ideally plastic Mohr-Coulomb constitutive laws embodied in FLAC3D were exploited. As expected, the width to height ratio of the pillar has proved to be the primary factor that determined the behavior of the pillars. Narrow pillars fail in a stable manner without the occurrence of instabilities. Intermediate w/h ratio pillars under the appropriate loading conditions, may fail suddenly and may even collapse totally. Squat pillars do show the potential for sudden, coal bump like side failure, but because the remaining large width of the inner core, the ruble around the pillar provides sufficient confinement so as to reestablish stability. Finally, the study revealed that the traditional Mohr-Coulomb law does not provide a useful insight into the failure of coal pillars. RESUME: L’utilisation des piliers de charbon dans les mines souterraines de grande profondeur occasionne des problèmes due aux difficultés de control de plafond et possibles fracture ou explosions au niveau des piliers. Aux Etats-Unies d’Amérique, l’utilisation des piliers dans les mines souterraines de charbon comme moyen de support est considèrees comme étant la plus grande et la plus importantes des méthodes utilisée dans le ‘’ longwalling method’’ ou une série des piliers sont disposé de manière à supporter les multiple entrées d’exploitation de charbon. En premier lieu, cette série des piliers étaient construit de manière conventionnelle avec un principe basé sur le fait que le poids exerce sur les piliers doit être inférieur a la force que ces piliers exerce sur le plafond. Ce principe a conduit a ce que le volume des piliers augmente au fur et à mesure que la profondeur au de la mine augmente. Malheureusement, au lieu de résoudre le problème de support, ce principe n’a fait qu’aggraver le problème de contrôle de plafond. Eventuellement une idée s’est dégagé allant du fait que les piliers endommagés de taille moyenne qui se sont avérés être efficaces ailleurs, pourraient fournir un indice à ce particulier problème. Le but de cette recherche est celui d’étudier les différent types de ruptures qu’un pilier peut occasionner lorsqu’il est utilisé a grande profondeur, tout en utilisant deux possible méthodes. La première d’entre elle comprend quelques solutions élémentaires obtenues avec l’aide d’une méthode simplifié et conceptuelle de la masse de la roche. Ce modèle consiste à prendre en sandwich la bande de minerais de charbon entre deux masses stratigraphiques sans pour autant endommager le plafond. La seconde méthode nécessite l’utilisation du ‘’ FLAC3D’’, qui est un logiciel commercialisé disposant d’un modèle numérique en 3 dimensions. Dans le but d’obtenir

Jan 1, 2003

By M. Mokgohloa, T. R. Stacey

Boring of tunnels and shafts in hard rock under high stress conditions is becoming more common as mines and tunnels are developed at greater depths. Under the high stress conditions, fracturing of the often-brittle rock occurs in the walls, backs, and ahead of advancing faces of excavations. Fracturing can have a significant impact on boring activities: sidewall spalling, which affects machine gripper capacity, and fractures can also develop in the rock ahead of the face, leading to blocky rock conditions, which may have a significant effect on machine excavation. Fracturing may develop dynamically, leading to rock bursts manifesting in the form of strain bursts, which can be hazardous and destructive. In brittle rock, fracturing is commonly extensional in nature. The focus of this paper is on fracturing in the face of the excavation. Examples of such fracturing behaviour are described briefly in the paper. Numerical analyses were carried out to predict the initiation of extension fractures and their orientations ahead of excavation surfaces, and the resulting formation of rock slabs/plates, and the stability of these plates. The results should be beneficial for the evaluation of the conditions prior to, and during boring operations.

Nov 27, 2024

By V. A. Myazin, M. V. Korneykova, A. V. Svetlov, V. G. Minenko, D. V. Makarov, A. L. Samusev

The paper discusses the treatment problem of mine (waste) water for enterprises of the Russian Arctic. The wide range of relevant pollutants, financial resources, the availability of land for the construction of a treatment plant, waste generated during the treatment process are some of the factors controlling current and future process design solutions. All mining operations have adopted water treatment and water quality monitoring solutions, however there is no single approach to the problem and each industry participant operates within the scope of its available resources. The range of existing and emerging methods is extensive — from using constructed wetlands for the deposition of mineral nitrogen compounds in settling ponds, reagent deposition and chemical coagulation in exhausted mine workings, and filtering dams on the surface to retrofitting existing mine drainage treatment plants with the adoption of the electrochemical coagulation process. Methods of wastewater treatment from heavy metals, oil products, and nitrogen compounds are demonstrated in the example of two industrial facilities in the Murmansk region. It was found that the use of electrochemical coagulation provides effective treatment of mine water from NO3, NO2, Ni, Fetotal and petroleum hydrocarbons (the degree of purification from 50.5-99.7%), the use of phytotreatment system provides wastewater treatment from ammonium ions and nitrite ions by 53-84%, nitrate ions - by 22%. Keywords: Industrial water treatment, treatment flowcharts, settling ponds, constructed wetlands, reagent sedimentation, chemical coagulation, electrochemical coagulation

Jan 1, 2020

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By A. A. B. Douglas

In this paper the origins of the mortar intruded concrete concept and its development and application in the construction of watertight bulkheads in South Africa are described. The events leading to the commissioning and execution of the West Driefontein Experimental Plug and the Virginia/Merriespruit Boundary Plugs, and their roles in the proving of the technique, follow. The development of the first Transvaal and Orange Free State Chamber of Mines Code of Practice for Mortar Intrusion Concrete for Underground Plugs and Bulkheads, Johannesburg, November 1962,is explained. The saga of the October 1968 flood and subsequent salvage of the West Driefontein Gold Mine is recounted. The paper concludes with mention of the validation programme carried out for the Placer Dome Western Areas Joint Venture and their South Deep water barrier programme.

Jan 1, 2006