Search Documents

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By Edson Charikinya, Pierre-Henri Koch

"The extraction of mineral values from ore requires liberation followed by separation steps. Liberation is achieved by size reduction operations which are energy inefficient processes typically dominating the energy consumption in a mineral concentrator. As the grade of ore reserves declines, future viability of mineral operations will be determined by energy costs of comminution. The application of high power microwave energy to secondary crusher products has been suggested as a possible commercially viable thermal treatment method for reducing comminution energy and improving value mineral liberation. Recent studies have shown that microwave pre-treatment of coarse sphalerite ore particles (> 5mm) at specific microwave heating energies (1-3 kWh/t), induces microfractures and creates new crack surfaces. This suggests that subsequent crushing of these microwave treated particles could yield enhanced liberation. However, limited studies have been carried out investigating the mode of breakage and the extent of enhanced liberation in that case. The objective of this study is to develop numerical methods for quantifying the extent of enhanced liberation and mode of breakage in crushed microwave treated and untreated particles. Sphalerite ore particles representing small (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm HPGR and cone crushed particles were microwave treated at specific energies between 1-3 kWh/t. Cracks in the ore particles before and after microwave treatment were analysed with QEMSCAN and numerical models of the measured particles (before and after microwave treatment) were developed in MATLAB. The propagation of random and non-random cracks was investigated by simulating comminution of the modelled treated and untreated particles. Results of this study demonstrate that the breakage mechanism and the liberation of valuable minerals from gangue in microwave treated and untreated particles is significantly different. This study contributes to the development of numerical tools to quantify crack propagation in heterogeneous ore particles."

Jan 1, 2018

By A. V. Bogdanovich

Until recently, in consideration of fundamentals of gravity concentration theory, all computations have been based on determination of particles? fall velocity in an unrestricted medium (hydraulic size). Meanwhile, gravity separation processes are realized under conditions of particles? restricted fall, when important and sometimes decisive role is played by interacting forces of particles, dependent on their varying size, density and shape, i.e., segregation forces. We have developed devices and methods for measuring segregation velocities of fine particles of various size, density and shape during their loosening in air or aqueous medium. Besides, to exclude influence of medium upward flows, loosening was provided by superposition of vertical harmonic oscillations on measuring cell. It was established, that maximum segregation velocities are observed at certain optimal acceleration values and amplitudes of oscillations; excessive loosening leads to mixing and worsening of segregation. Velocity of some particles segregation through others depends on particles? size, density and shape, as well as nature of medium (air, water). Absolute segregation velocities of particles in air medium may reach 1~2 mm/s, in aqueous medium such velocities are by an order smaller. Analysis of rare-metal sands material gravity concentration results showed, that owing to segregation process during gravity separation, fine-size isometric particles of heavy minerals are recovered into gravity concentrates more actively, than larger ones, but more elongated in shape. It is convenient and simple to estimate mineral grains? shape by extent of their oblongness, described as ratio of particle minimal dimension to maximum. Besides, mineral mixtures gravity separation results are directly related to extent of oblongness of heavy particles, recovered in gravity separation process, and also to root-mean-square coefficient of their shape variation. The performed research showed that particles segregation in gravity concentration process plays not a lesser role, than hydrodynamics parameters, and demands further theoretical inquiry and experimental studies.

Jan 1, 2014

By Wei Sun, Xue-feng Cao, Lei Sun, Run-qing Liu

The flotation performance of kaolinite in laboratory micro-flotation was investigated with 3- (dodecyloxy) propan-1-amine (ON12) as the collector. Compared with dode cylamine (DDA), which is commonly used as the bauxite reverse flotation collector, ON12 shows stronger collecting ability for kaolinite than using the same amounts of DDA, when experimental pH value reaches more than 6. With the addition of ON12, the isoelectric point of kaolinite shifts to 6.1 from 3.6, which suggests a strong adsorption between kaolinite and ON12. Infrared spectra analysis indicates that the type of ON12 adsorbed on the kaolinite surface is mainly of electrostatic adsorption. Molecular dynamics simulation further indicate that electrostatic adsorption of ON12 cation on kaolinite (001) surface based on electrostatic interaction between NH4+ and O atoms. ON12 will be suitable for bauxite reverse flotation with the efficiency depressors of the diaspora.

Jan 1, 2014

By T. Wajima

We tried to convert paper sludge ash (PSA) into zeolitic product with high cation exchange capacity (CEC) through acid leaching. Typically, PSA from incineration of paper sludge contains a high percentage of calcium in the form of anorthite (CaAl2Si2O8) and gehlenite (Ca2Al2SiO7). It is difficult to convert the ash with a high Ca content into zeolites, or at least into more desirable zeolite phases. Acid leaching with HCl was applied to reduce the Ca content to synthesize zeolitic product with high CEC. The raw ash was treated with 1 M, 3 M, and 5 M HCl solution for 0.5~24 hours (the ratio of the ash to volume of HCl solution was 1/4), and then zeolitic product was synthesized from leached ash through the reaction with 2.5 M NaOH solution at 80 oC for 24 hours. During acid leaching, gehlenite is readily dissolved in a lower HCl concentration solution than anorthite. With increasing HCl concentration, the amounts of Ca, Mg, Si, Al, Fe and Ti extracted from the ash increased. Ca and Mg contents were easily extracted from ash than other elements. The contents of Ca and Mg extracted rapidly at initial stage, and then levelled off. The saturation times of Mg and Ca are almost 0.5 h using all concentrations of HCl solutions. After the synthesis from leached ashes, zeolite-A and -P were synthesized from ash leached in 1 M HCl solution, and 3 M and 5 M HCl solutions, respectively, regardless of leaching time. With in-creasing HCl concentration, the Ca content eluted from the product decreased, due to the removal of Ca via acid leaching before the synthesis, while the Na content eluted from the product increased to 3 M HCl and then decreased, which was almost similar to the CEC of the product, due to the ion exchange of Na-type zeolitic phase in the product. The change of zeolite phases in the product and the CEC of the product depend on the concentrations of Si and Al in the solution during the synthesis. The highest CEC of the product is about 220 cmol/ kg, which was synthesized from the ash leached in 3 M HCl solution.

Jan 1, 2014

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By E. Vahidi

In this study, a hydrometallurgical treatment involving solvent extraction of zinc using D2EHPA (di-2-ethylhexyl phosphoric acid) has been investigated to recover zinc from an industrial zinc leach residue. The residue was leached with sulfuric acid producing leach liquor which was subjected to solvent extraction for enrichment of zinc and removal of impurities. Operating variables for the zinc extraction process, such as pH of the mixed solution (0.5~5.0), concentration of D2EHPA (5%~40%, w/w), temperature (25~60°?C), A/O volumetric phase ratio (1/2~4/1), concentration of tri-butyl phosphate (TBP) as modifier (3%~7%, w/w), concentration of NaR2RSOR4R in aqueous phase (0.05M, 0.1M, 0.2M) were also studied. Practically all zinc was extracted from the aqueous solution at pH 2.5 with 20% w/w D2EHPA in kerosene. At this operating condition, zinc could be extracted at one theoretical stage at A/O phase ratio of 1/1, as calculated by the McCabe-Thiele method.

Jan 1, 2014

By X. F. Cao

There was a large reserve of bauxite resources in China. And these resources were mainly the dias-pore-bauxite and contained plenty of aluminosilicate including kaolinite, illite and pyrophyllite. Reducing the contents of aluminosilicate would be significant to the using of Chinese bauxite resources. In this paper, from the single mineral flotation experiments, the surface properties and flotation beha-viours of aluminosilicate including kaolinite, illite and pyrophyllite, using dodecyl amine (DDA), N, N-dimethyl-dodecyl amine (DRN12) and N-dodecyl-1, 3-propane diamine (DN12) as collectors, had been investigated. The flotation results shown that the flotation behaviours of aluminosilicate had been influenced greatly by three amine collectors; and the effect was in the order of DN12>DRN12 >DDA. On the basis of FT-IR spectra and zeta potential measurements, the ionization of surface hydroxyl, as well as isomorphic exchange of surface ions, accounted for the mineral surface charges. And the mechanisms of interactions between the mineral surface and collectors mainly included two modes: electrostatic adsorption and hydrogen bonding; for the DDA and DRN>DDA. 12, the mechanism was mainly electrostatic adsorption; and for the DN12, the mechanisms of electrostatic adsorption and hydrogen bonding both existed. Results of quantum chemistry research shown that the collecting ability of amine collectors was greatly influenced by the electro-negativity of N in the amine molecules; and The |E(EHOMO| and ?E (HOMO-ELUMO) of N atom in DRN12 and DN12 were lower than that of DDA, and the positive charge of ?N group in DRN12 and DA12 were higher than that of DDA. All these calculation results could explain the collecting power of DN12>DRN12>DDA.

Jan 1, 2014

By Gurubasayya Swamy

This paper presents the performance study of sag mill in the processing of gold ore. Deterioting ore grade and high demand of metals has tremendously influenced the SAG mills. Today?s high capacity Semi-autogenous grinding (SAG) mills expand vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. Semi-autogenous (SAG) mill performance is influenced by ball charge, feed properties, shell, grate, and pulp lifter design. In the performance study of SAG mill, based on the results obtained it can be observed that SAG mill performed better at feed size +4 inch and grinding media consumption 0.90kg/mt. In the present study the effect of crusher bypass on SAG mill performance, an immediate drop of throughput ranging from 10-20tph is observed. Keywords: sag mill, pulp lifters, grinding media, energy, consumption, throughput

Sep 1, 2012

By Fedotov Pavel

"Today the main objective of improving the process of ore dressing is to reduce energy consumption and performance of the basic rule of auxiliary enrichment processes. One of the modern means of ore destruction with a minimum of energy consumption is the interparticle fracturing, for example in the roller press. There still remain the unsolved problems of the energy consumption determination and the particle size distribution of the crushing product .Existing methods for determining these parameters are empirical and require considerable expenses and time. The improved finite element was developed to solve these problems using finite element contact interaction of the rock. Also it was developed to clarify the stress-strain and the rock fracture energy in a layer. These elements are used to study ore destruction in the layer and allows to create a model taking into account the interaction of crushing particles surfaces. The same algorithm was developed determining crushing product particle size distribution in the layer on the base of the Bond’s theory of crushing. The presented finite element model allows to determine the quantity of strain energy and particle size distribution of crushed product during the destruction processes of the material in the roller press with fair accuracy."

Jan 1, 2014

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Dietmar Freyhammer

Grinding is the last stage of the comminution process. In the grinding process the particles size are reduced by impact and attrition stresses. The fine grinding of ores is nowadays finding increased application due to depletion of coarse grained, easily processed ore bodies and the increased need to process distributed fine grained deposits, such fine ground iron ore powder is the basis for the pelletisation process. Depending on the ore type and the project environment different approaches to comminution are requested to provide an adequate ground iron ore for the pelletisation process. Currently the ball mill is the most used equipment in grinding iron ore for pellet feed. Based on the various examination and investigation of minerals on grind ability related to the throughput, to the resulting sieve characteristics and necessary energy consumption, the mill circuit can be: Open dry circuit. Closed dry circuit Open wet circuit Closed wet circuit. CEMTEC GmbH is a renowned name worldwide and offers tailor made solutions to cope these issues.

Sep 1, 2012

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014