Search Documents

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By Hoon Lee

Laboratory tests were conducted to evaluate the breakage characteristics of pyrophyllite in a laboratory ball mill. In grinding tests, the breakage characteristics were analyzed using the mathematical kinetic models based on the two breakage functions; the specific rate of breakage and the primary breakage distribution. Two samples having similar chemical composition show identical values in specific rate of breakage. In comparison, there are different values of primary breakage distribution for each sample. The size distributions of the product with various grinding time are well described by the parameters from non-linear searching.

Sep 1, 2012

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

The air recovery from a flotation cell is the fraction of inlet air which overflows the weir as un-broken bubbles. The air recovery is an important factor in froth phase phenomena; such as gangue entrainment and froth recovery. Increasing the air recovery, results in a higher recovery of attached mineral particles. Air recovery can be measured experimentally on plant using image processing of the top surface of an overflowing froth. The air recovery is directly linked to froth stability and the bursting rate of the bubbles at the froth surface, making it very difficult to predict. Experimental results show a very strong correlation between the superficial velocity of the inlet air and the superficial velocity of the air leaving the cell through the froth surface due to bursting, calculated from the experimentally measured air recovery. This correlation holds over multiple banks from different plants. Development of a power law equation around the inlet air velocity and the bubble solids loading on the froth surface allows the superficial air velocity through the top surface of the froth to be predicted, and from this the air recovery. This model is valid for use when operating beyond the peak in air recovery.

Jan 1, 2014

By Y. P. Lu

PET/kaolin nanocomposites were prepared with melt blending and the structure of the composites was characterized through IR techniques. The results showed that there is stable chemical bonding between PET and kaolin. In addition, the dispersion condition of nanokaolin was observed by means of SEM and TEM. As a result, the thickness of the dispersed nanokaolin particles in PET matrix is mainly from 20mm to 200nm, and the nanosized particles congregate to some extent in the samples. In addition, it was found the kaolin particles almost homogeneously dispersed in the PET matrix, without preferential orientation because of the shear effect due to melt blending. Furthermore, the mechanical properties of PET/kaolin nanocomposites are dependent on the modification efficiency of nanokaolin. With the poor efficiency, the nanokaolin particles tend to aggregate at a high content and have a bad interfacial compability between nanokaolin and PET matrix, which lead to stress concentration, so the mechanical property descends. Experiments of different contents of modified nanokalin indicated that the intensity of PET/kaolin nanocomposites decreased firstly, then increased, and then decreased, with the nanokaolin content of 4 to 5 percent, the rupture stress of the composites showed a maximum value, which was higher than that of pure PET. On one hand, nanokaolin decreases the function among PET macromolecules, which will decline the mechanical properties, on the other hand, the piece structure of kaolinite improves the intensity of the nanocomposite. When the nanokaolin content is low, the former has the dominant effect on mechanical property, while the latter will play a leading role with the content increasing. But if the nanokaolin content still increases, the agglomeration and stress concentration will be obvious.

Jan 1, 2014

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By Jonas Addai-Mensah

Despite the fact that nickel (Ni) laterites accounts for about 60 % of the world?s nickel mineralization, commercial processing of complex, low grade Ni laterite ores by conventional beneficiation (e.g. magnetic, electrostatic and flotation separation) still presents intractable challenges, particularly in heap leaching. Invariably, low grade laterite ores require aggressive hydrometallurgical techniques (e.g., highly acidic lixiviant leaching at ambient or elevated temperatures) for Ni and cobalt (Co) extraction. As a precursor to heap leaching, agglomeration of the multi-mineral phase feed particles into robust and porous granules of 4-10 m permeable bed, is essential. In the present work, several basic and applied studies of the agglomeration behavior of real Ni laterite ores and selected oxides and clay minerals (hematite, quartz smectite and kaolinite) which constitute the predominant host gangue phases of typical laterite ores are performed. Isothermal, batch agglomeration tests involving sulphuric acid solution as a binder were carried out to produce coarse, narrow-sized (5 ? 40 mm) granules which were well characterized. The influential role of feed ore characteristics (e.g., mineralogy/chemistry and primary particle size distribution) and binder composition (30 vs. 44% w/w H2SO4) and dosage (15-25 wt.%) in agglomeration behavior and granule properties were examined through several characterization techniques including granule size, compressive strength, bed percolation and re-wetting stability and 3-dimensional micro-structure analyses. Links between feed mineralogy/chemistry and size, binder formulation, agglomeration behavior, curing conditions and final granule properties and structural characteristics are established. The implications of the findings to Ni laterite plant agglomeration for enhanced heap leaching are discussed. Keywords: nickel laterite, complex low-grade ores, agglomeration, heap leaching, micro-structure

Sep 1, 2012

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By B. A. Kutlin

29% of the total ore mined in the Russian Federation for copper production is finely disseminated copper-zinc-pyrite ores of the Ural Region. Physical and chemical characteristics of pyrite copper-zinc ores make for difficulties in obtaining high indices during processing. At present, the authors have elaborated the technology to improve the quality of copper concentrates up to 20.0% for the ones obtained during pyrite copper-zinc ore processing (based on the example of the ore mining and processing enterprise ?Uchalinsky GOK?, Russian Federation). There are examples of use of fair-sized pneumo-mechanical flotation machines by modernization of processing plants. Keywords: copper-zinc-pyrite ores, Ural region Russian, selective flotation, pneumo- mechanical flotation machines

Sep 1, 2012

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By V. Vogt

During the phosphating of car bodies containing aluminium, the employed phosphating chemicals zinc, manganese and nickel are, for thermodynamic reasons, only used to a limited extent for the desired surface coating. The major proportion of these metals is discharged together with the incidental cryolite-containing phosphating sludges and the rinse water. Commissioned by the German Federal Ministry of Education and Research (BMBF), the Institute of Mineral and Waste Processing, Waste Disposal and Geomechanics at the Clausthal University of Technology has developed a two-stage process for the production-integrated recovery of the dragged out chemicals and for closing the rinse water cycle for Audi AG. During the first stage, the phosphating chemicals are recovered by means of leaching. In the second stage, the rinse water is treated by means of electroflotation followed by an ion exchanger.

Jan 1, 2014

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By Sanja Miskovic, Manjunath Basavarajappa

In this study, a coupled CFD-DEM (Computational Fluid Dynamics-Discrete Element Method) approach is used to simulate two-phase, solid-liquid flow within the flotation cell. Turbulence plays a key role in flotation cells and level of turbulence is affected locally by the presence of particles. Turbulence in the flow is modelled using Reynolds Averaged Navier-Stokes (RANS) based k-e model. Using particle transport and spatial distribution, mixing mechanism for differed sized particles are analysed. By including the effects of particle-particle collision, particle rotation, and particle translation, as well as the volume occupied by the particles in the fluid, CFD-DEM approach can be used to accurately predict the motion of particles in the turbulent solid-liquid flows with strong coupling. Electrical resistance tomography (ERT) is used to investigate the effect of impeller size, shape, off-bottom clearance and impeller speed on mixing and suspension behaviour inside flotation cell. The effect of flotation impeller design, impeller size, and off-bottom clearance on flow hydrodynamics is investigated. In the case of moderate and high solids loading (> 10 %w/w), energy is dissipated through inter-particle interactions and four-way coupling becomes important (Derksen 2003). The main goal of this study is to understand the effect of particle size and concentration on flow dynamics at high Re in highly turbulent systems using advanced modelling and measurement techniques. Experimental measurements obtained by ERT) system allowed detailed mapping of temporal hold-up profiles of the dispersed phase. Impeller size and off-bottom clearance are found have significant effect on the particle suspension characteristics.

Jan 1, 2014

By N. Gurulaxmi Srikakulapu

The demand for high-grade iron ore has increased the importance of beneficiation of low-grade iron ores. The captive mines of Tata Steel Limited, India has reserves of Banded Haematite Jasper (BHJ) ore assayed 40% Fe, 40% SiO2 and <1% Al2O3. QEMSCAN study has revealed haematite and quartz as a major iron bearing and gangue mineral phases respectively. Liberation characteristics have showed 80% liberation can be obtained at particle size below 10µm. In the present study, reverse cationic froth flotation of BHJ using ether diamines is explored in Denver-D12 flotation cell. Polynomial response surface regression equation coupled with six-factor Box-Behnken design of experiments is used to generate the correlation between process separation efficiency and flotation parameters. Flotation studies of BHJ indicated that concentrate of 62% Fe can be achieved with 62% Fe recovery from Jig concentrate at optimum conditions. The obtained product can blend with pellet fines to feed in blast furnace. Keywords: banded haematite jasper, flotation, box-behnken design, response surface methodology

Sep 1, 2012

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014