Search Documents

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By Yuhe Tang

High Gradient Magnetic Separator with Horizontal Magnetic Line is a new type High Gradient Magnetic Separator product. It has many specific advantages, such as water-air joint discharging technique, double pulses pulp dispersion technique, multi-magnetic gradient for collecting matrix with different diameter rods, better discharging rate with the especial matrix dispose, high separating accuracy and wide applicability. In this paper, the author makes a description of High Gradient Magnetic Separator with Horizontal Magnetic Line, and puts its emphasis on analyzing industrial production data using high gradient magnetic separator with Horizontal Magnetic Line to separate weakly magnetic minerals. It is found that as the rougher for weakly magnetic minerals separation, High Gradient Magnetic Separator with Horizontal Magnetic Line has more stable metallurgical performance and cheaper running costs than other types of High Gradient Magnetic Separator when the properties of the ore change greatly and there is in the case of embedded fine particle size distribution. Keywords: high gradient magnetic separator, self cleaning technology, horizontal magnetic line, water air discharging technique

Sep 1, 2012

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By R. Paturi

Mill liners play an important role in the operation of a mineral concentrator influencing the throughput, availability, power drawn and the efficiency of the mill in the plant. Liners protect the shell and transfer energy to the grinding charge. Metso Technology Development has conceptualized, developed and successfully implemented physics based 3D DEM simulation techniques to predict charge motion, power drawn, energy spectra and wear over the life of the liner. This paper will present a case study of shell liner optimization for a 34? SAG mill including the input data requirements, and shell liner optimization methodology using the 3D simulations that eliminates the need for the traditional expensive and lengthy proto-type testing. These simulations will cover ball and particle movement, liner wear and mill power draw, and do not cover particle breakage and slurry flow. Even the liner manufacturers lack the ability to provide this type of qualitative and quantitative information on their products. The data from these simulations provides the plant engineers a scientific basis for their decision making and thus eliminates guess work. Keywords: liner, optimization, multi-physics, 3D-DEM

Sep 1, 2012

By Kwang Soon Moon

Liquid ? liquid reactions such as solvent extraction in hydrometallurgy and BTX extraction in petrochemical industry has long suffered from the long retention time mainly due to the limited interfacial area caused by the immiscibility between water and oil phase, requiring typically very large perfect mixer type reactors and tall adsorption towers. A novel spray reactor for immiscible liquids; that is the KISEI Nozzle Reactor (KNR) was introduced, enabling the drastic increase in the interfacial area between the reacting immiscible liquids. Various spray mechanisms were applied in materials processing, e.g. spray drying, powder metallurgy, and aerosol industry, but not in hydrometallurgy. The KISEI Nozzle Reactor(KNR) was fully developed and used in production of biodiesel from the immiscible triglycerides and methanol. An experience with a full production plant facility is briefly discussed in the current paper. With the fog-like methanol spray in oil medium, the trans esterification reaction was almost instantaneous, and transformed the traditional batch trans esterification process into a continuous production process. And above all, with no moving parts in the KISEI Nozzle Reactor (KNR), the process requires minimal operation and maintenance costs. Keywords: immiscible liquids reaction, nozzle spray reactor, continuous biodiesel reactor, hydrometallurgy, organic extraction, micro emulsion

Sep 1, 2012

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By Ljudmil S. Grigorov, Eric Forssberg, Hanumantha Rao Kota, Robert J. Pugh, Lidia B. Alexandrova

"We have used the microscopic thin balance developed by Scheludko at al. (1970) technique to study the stability and interactions within the thin film between the silica surface and air bubble with (i) a long chain C10 amine and (ii) a cationic/anionic surfactant systems consisting of mixtures of a long straight C10 chain amine with long straight chain C8, C10 and C12 sulfonates. It was found that the mixed surfactants caused lower contact angles, lower rates of the thin aqueous film rupture and longer film lifetime, compared to the pure amine system.This behavior was explained by the initial strong adsorption of positively charged interfacial complexes from the mixed surfactant system at the air/solution interface followed by adsorption at the silica interface. It was also shown that the chain length compatibility between the anionic and cationic surfactants controls the strength of the interfacial complex, determining an inhibition in the thin film rupture and dewetting of the film. The rupture mechanism was explained by an earlier established heterocoagulation mechanism between the positively charged air/solution interface and the solution/silica interface which remained negatively charged. The formation of the interfacial complex at the air/solution interface was confirmed by using surface tension data."

Jan 1, 2003

By Bianca Foggiatto, Marcos Bueno, Rajiv Chandramohan, Eddie McLean, Greg Lane

"With the increasing depletion of high-grade ore deposits, smarter mineral processing solutions are required to achieve sustainable and economic methods for mining and processing low-grade deposits. In order to make the treatment of low-grade deposits economically viable, large quantities of rock need to be mined and processed. The associated infrastructure costs (power, water supply, accommodation and support services, waste storage) result in a substantial penalty on the project, from both capital and operating cost perspectives. As a consequence, the challenge for the mining industry is to overcome the associated rise in energy and water consumption as well as increased project complexity when processing large amounts of low grade ore. Ore sorting technologies have been used for many years, predominantly on small projects, enabling the upgrade of marginal ores. Several sorting methods based on characteristics including specific gravity, radiometry, colour, particle size, grade and other detectable physical characteristics have been employed. The challenge for large low-grade ore bodies is to crush and sort at coarser rock size in order to minimise specific energy consumption in comminution and to reduce waste disposal costs. For large projects, the understanding of the economic impact of ore sorting is limited. The economic drivers include plant head grade improvement; sorting infrastructure capital, operating and maintenance costs; waste material handling and other environmental costs related to waste disposal. This paper analyses the economic impact of ore sorting in a large mineral processing operation. The focus of the analysis is to compare NPVs for a circuit including screening and ore sorting stages. A project for processing an Australian copper sulphide ore is considered as an example for this study."

Jan 1, 2014

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By Alexey P. Tatarinov

Under modern economic conditions in Russia, gold heap leaching is the most effective way of investing into gold-mining industry. Gold is recoverable from small-size deposits, low-grade ores from oxidation zone, cut-off grades, and overburden rocks using heap leaching. This technology is cost-effective and allows a saleable metal to be obtained within the first year of operation. The investments for heap leaching are lower than those of for a traditional plant technology. Production cost per one gram of Au is 5-7 times lower than that of during a plant flow sheet. A seasonal development of mines can be possible. With reference to this, heap leaching resembles the technology of placer deposits development. One of the major advantages of heap leaching is the form of the product. Gold can be obtained as dissolved in a clarified PLS, which allows the further quick treatment. The amenability of ores to heap leaching depends on their mineralogical composition. Oxidized porous ores with a good access of a lixiviant to valuable particles can be treated without pre-crushing. Clayish minerals are often found in oxidized ores with free gold. In order to build ground for heap, several major methods combined with various pad materials are used. These methods have been used at many plants and are reliable. The development of heap leaching technology for gold ores for the deposits from Yakutia, Zabaikalsky region, Primorye region, Uzbekistan, Tadjikistan, and Kazakhstan began in the 70s. However, it has been commercially used only since 1990. The first heap leach plants were built and commissioned in the USSR in 1991 at Vassilkovsloye deposit (Kazakhstan) and at Maiskoye deposit in Russia in 1994. Pilot plant testing was conducted in 1996 using ores from Kuranakh ore field, deposits Phiskulturnaya-Kholodnaya and Lopukhovskoye from the Aldan region. After the first successful commissioning of heap leaching plant in Russia, this technology has been commercially applied for deposits. Every year 1-2 heap-leaching plants were commissioned. More than 30 heap-leaching plants have been commissioned both in Russia and in the former Soviet Union using technologies developed by IRGIREDMET. Keywords: cyanide leaching, heap leaching, ore, percolation, solutions, lime technology

Sep 1, 2012

By T. S. Qiu

In view of the bad effect that Na-bentonite direct adsorb Pb2+-containing wastewater, this article has carried out two kinds modification treatment on Na-bentonite: the direct microwave radiation modification and microwave radiation organic modification by adding quaternary ammonium salt?cetyltrimethylammonium bromide,and analysis the main influencing factors of the modification effect. In static conditions, preparing Pb2+-containing wastewater as the research object, it has respectively studied the effects of Na-bentonite, microwave soil of direct microwave modification and microwave soil of organic modification on the process of adsorption Pb2+, and discusses the effects of pH value, temperature, adsorbent dosage, stirring time on the adsorption Pb2+ in wastewater by modified bentonite, at the same time it does a verification test to the practical Pb2+-containing wastewater. Comparison the effects of adsorption Pb2+ in wastewater, the results show that organic modified microwave bentonite is obviously better than direct microwave modified bentonite and Na-bentonite, and can make 6 mg/L Pb2+-containing wastewater meet the national discharge standards. Through scanning electron microscope, the result of test is that organic modified microwave bentonite is the cause of improving adsorption Pb2+ in wastewater. Preparing modified bentonite by microwave heating will not only shorten the response time, reduce energy consumption and work-load, but also modified effect is good.

Jan 1, 2014

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By A. Prokopiev

The biological stage of reclamation is the third final stage in remediation the damaged mining terrains, which is carried out following the completion of the mining technical stage. The biological stage of reclamation is carried out through restoration of the vegetation layer. The biological reclamation includes all activities related to the introduction into the terrain of vegetation, microorganisms, insects, and animals, with the acceleration of the succession and creating conditions for a sustainable ecosystem close to the natural one. It comprises of all anti erosion and other activities such as the preparation of the land for growing agricultural crops, sowing grass seeds, planting seedlings, amelioration of the soil and further care for the vegetation until its final place on the land. Mineral and organic-mineral ameliorants for biological reclamation were studied. The basic mineral ameliorant is Bulgarian natural zeolites. The zeolitic-rich tuff samples provided from Golobradovo deposit was characterized by their chemical and mineralogical composition and ion exchange properties and X ray analysis. The average content of clinoptilolite was found to be more than 80%. The materials had ion exchange capacity (NH4+) varying from 100 to 110 meq/100g. Chemical modifications of natural clinoptilolites were made in order to form active phases of nitrogen, phosphorus, potassium, and microelements. Slow-acting mineral ameliorant was developed. Organic-zeolite substrate for biological reclamation was developed. This new product is a mechanical mixture of organo-matter and modified zeolites. Agro-chemical parameters of new ameliorants were determined. The substrates including studied overburden dump soil and mineral or organo-mineral ameliorants are produced. The grass growth test was performed. Keywords: biological reclamation, ameliorants, damaged mining terrains

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By E. Guerrini, M. Maccagni, J. Nielsen

"Lead is the most important material able to meet the current demand for energy storage. The lead acid battery is reliable, efficient and inexpensive. Continuous developments in battery construction are providing improvements in all aspects of the batteries’ performance. The lead acid battery is both the main lead product and the main raw material for lead production. More than half of the lead produced is from secondary smelters where batteries are the most important feed material. The environmental pressure on lead production has been increasing for many years, and continues to become stronger and stronger. The lead production processes and technologies themselves will require updating to meet the new regulations. Although they are very strict now, they will become even more so and current technologies may not be sufficient. Because recyclability is a strong point for the lead acid battery, the secondary smelters need to reduce the environmental impact as much as possible. In recent years, the secondary smelters underwent impressive changes in this direction, but some more improvements are possible. Electrochemistry can offer a step change improvement in making secondary lead production more environmentally friendly. Engitec has developed an electrochemical process base on a very high current density (high productivity) cell using an inexpensive electrolyte and at a relatively low cost. In this paper, the latest update on the technology is provided. INTRODUCTION The lead acid battery is considered the “walking dead” by some new technologies trying to replace it. It has played and will continue to play a very important role in our lives because it is inexpensive, fully recyclable and the existing lead and the mine reserves guaranty enough material for the extended future. According to the life cycle, the lead acid battery is the cheapest and the most effective system to store energy. Lead is practically a close loop where lead battery production consumes more than 80 % of the produced lead but contemporarily it is the most important raw material for the production of metallic lead. In fact, nowadays, the secondary production has overcome primary production and this trend is expected to continue. Primary lead is the make-up material for the existing battery production and the source of lead for the construction of the new ones."

Jan 1, 2018