Search Documents

By Manqiu Xu, Glen Robertson, Steve Wilson, Pete Quinn

"The middlings circuit, once called the pyrrhotite rejection circuit, at Inco’s Clarabelle mill was a single flotation stage. It used to process a combined feed consisting of the main flotation scavenger concentrate and the non-magnetic portion of the magnetics flotation circuit tails. The typical circuit metallurgy was 55% nickel recovery at 6.5% Cu+Ni concentrate grade. In the past few years, a research project with the objective of improving the circuit metallurgy was initiated between Inco’s research laboratory and the Mill’s Process Technology group. This project has gone through three steps: a) initial laboratory studies, b) on-site pilot plant investigation, and finally c) full plant implementation.The present paper describes the initial laboratory test work. The development of a two-stage circuit consisting of separate rock and pyrrhotite rejection stages to replace the simultaneous rejection of both rock and pyrrhotite in a single stage is discussed. A two-stage circuit simulation based on batch laboratory flotation data is also presented. Further development work, including the on-site pilot plant test work and the plant implementation of the new circuit design, will be described in a later publication.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill, Copper Cliff, Ontario processes a rich complex sulfide ore from several large production mines around the Sudbury basin (Agar, 199 1). The sulfide mineralization is simple, consisting of chalcopyrite (Cp), pentlandite (Pn) and pyrrhotite (Po). The main gangue minerals are pyroxene, feldspar and quartz with minor amphibole and talc. Estimates of mineral composition are routinely calculated from Cu, Ni and S assays. In the mineralogical calculations, all gangue minerals are conveniently grouped and treated as rock (Rk)."

Jan 1, 2000

By Pierre Beaudoin

"This paper deals with the repairs made on two damaged mills. It investigates briefly the causes of the damage, explain its nature and the design of the repair. It explains the detrimental effect on operation and the solutions implemented to reduce them. Finally, to review the follow-up required for such repairs. LOCATIONThe Holt McDermott Mine is located 75 kilometers Northeast of Kirkland Lake and 30 kilometres west of the Quebec border in Northeastern Ontario. The town of Kirkland Lake is located approximately 500 kilometres north of Toronto. HISTORYThe discovery of gold in Holloway Township dates back to early 1920. In 1984 Barrick Resources, which amalgamated with Camflo Mines, acquired more claims on the property and initiated an extensive drilling program. By 1985, the drills indicated reserve increased to 2,500,000 tonnes grading 6.8 g/mt. In 1986 a production decision was made and in 1988 the mine was officially opened.As of December 31, 1998, 4,691,507 tonnes grading 5,66 g/tonnes have been milled from 4 ore-bodies. The mill started up in June 1988."

Jan 1, 2001

By C. E. White

History The Con-Rycon mine is situated in the Yellowknife mining district, North West Territories, 608 air miles north of Edmonton, Alberta. The earliest reported discovery of gold in the area was made in 1898 but no extensive exploration occurred until 1928. The birth of Yellowknife as a mining community took place in 1934 with the staking of the Rich group and subsequent shipping of 16 tons of high grade ore. The Giant group was also among the claims staked in 1934, and later staking showed a tendency to close the gap between these two properties. In the fall of 1935, the A.Y.E. claims, situated south of the Giant group, were staked to cover a discovery of the Geological Survey of Canada and, after general release of the Survey's information, the adjoining ground was staked. These claims included the Con, Negus, Meg, and Kam groups. In 1936 four lapsed claims were re-staked as the P and G group and later acquired by Rycon Mines, Limited, controlled by the Consolidated Mining and Smelting Company of Canada, Limited. The Con and various adjacent groups owned by Cominco are now operated with the Rycon under one management. Surface trenching on the Con property started in 1936 and, during the fall and winter of 1936-37, a 60- foot 5 ft. by 9 ft. inclined prospect shaft was sunk. The encouragement provided by the shaft and diamond drilling in 1937 led to the decision to establish a mining plant, and in August, 1938, the 100-ton cyanide mill produced its first brick- the first gold brick poured in the history of the North West Territories. In November, 1938, the mill was enlarged to a 175-ton capacity and operated at this rate until 1941, when refractory ore was encountered. This situation was met by the installation of flotation and roasting units and, at the same time, the milling capacity was increased to 300 tons daily. Labour shortages and Government restrictions forced a reduction of output and in 1943 milling was suspended while mine development continued on a reduced scale throughout the war years. The present full-scale of operations was resumed in 1946 and the total production to the end of 1948 amounted to 288,853 oz. gold and 72,347 oz. silver.

Jan 1, 1949

By Sydney C. Mifflen

COAL MINING, with its some 15,000 employees, is directly responsible for the livelihood of one-fifth of the population of the Province of Nova Scotia and indirectly so for that of possibly another fifth. Deposits of coal are known and worked in four counties of the Province, from which is being produced yearly tonnages as noted below: Cumberland County 750,000 tons Piccou County 400,000 tons Inverness County 100,000 tons Cape Breton County 5,250,000 tons TOTAL FOR NOVA SCOTIA 6,500,000 tons Production in Cape Breton county is entirely from the one source, the Sydney coalfield, and not only is this field the most important in respect to output, as is disclosed above, but it is also the largest presently known deposit in the Province and holds the greatest tonnage yet in reserve for future mining. In the light of the above more or less generally known facts, it is trite to remark on the importance of the Sydney coalfield in the internal economy of the Province. On the other hand, not nearly as well-known nor as frankly recognized is its significance in the national life of Canada, for from this field is produced not only 80 per cent of the Nova Scotia coal but over 40 per cent of all coal mined in the Dominion. Another noteworthy comparison can be made from the fact that the Sydney field contributes 22 per cent of all the bituminous coal consumed in Canada, the remainder being made up of 7 per cent mined elsewhere in Nova Scotia, 27 per cent from other parts of Canada (British Columbia and Alberta, principally), while the remaining 44 per cent is imported, practically wholly, from the United States of America.

Jan 1, 1941

By Paul H. Atkinson

"Sampling in the mineral processing industry has always been a subject which has received considerable discussion. There have been many volumes written on theory, techniques and practical application of sampling. However, until recently, the companies were not completely aware of the potential savings available with properly designed sampling systems both to assist in pieces: control and final product values.Definition In our discussion today, we will define sampling as the operation of removing a part, convenient in quantity for analysis, from a whole, which is of much greater hulk, and removing it in such a way that the proportion and distribution of the quality to be tested, i.e. size of particle, moisture content, specific gravity content, mineral and chemical composition, are the same in both the sample and the whole.Application It has been well established that undetected errors can result in large economic losses, thus most firms depend upon some type of sampling and sample analysis as a control in their continuous processing of materials. Despite the large investment in facilities and personnel the ""analysis"" of a sample can be no more accurate or reliable than the sample on which it is being based. The importance of sampling is recognized by a great many but it is appreciated by only a few, largely because it is sometimes one of the items which is taken for granted."

Jan 1, 1976

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By Brian Flintoff

"When I was first asked to prepare this paper and presentation in late June, I thought it might be fun to ""step back and paint the bigger picture."" Having attempted to do this, fun is not the first descriptor that now comes to mind, and speaking dyslexically, I've had 'nuf.'Unlike Nostradamus, or even Orwell, I've discovered that I'm ""clairvoyantly challenged"" and not even the psychic hot-line was of much help, at least with respect to process control! I am somewhat comfortable speculating on evolutionary change, but the radical developments that will arise from revolutionary changes are well beyond my mortal capabilities. Even with evolutionary change, I'm reminded of the lessons of time series analysis which show the prediction error to grow exponentially as the horizon moves into the future. As Macluhan is reported to have said: ""Predicting the future based on the past is a little like driving your car while looking in the rearview mirror!""Having honestly presented my qualifications, allow me to try to look at process control and to offer some conjecture on where we're probably headed. In the end, it is said that: ""The plant of the future will have only two employees, a man and a dog. The dog will be there to keep the man from touching the equipment.1""IntroductionA little less than a decade ago Andy Mular and I co-edited a monograph entitled ""A Practical Guide to Process Control in the Minerals Industry."" The work was commissioned by the senior management of a consortium of Canadian mining companies, since it was widely perceived that control was an area of great economic potential, but one that had not been effectively tapped. The concern was that if the industry could not soon deliver on the ""potential"", the term may well have appeared in the epitaph of what was, to these men, a very attractive investment opportunity. I think it is fair to say that over the past few years process control has clearly established itself as an essential technology in plant operation and optimization. That isn't to say that we get it all-right, all-the-time, but, the circumstances are much different than they were. In the eyes of many, process control has attained the distinction of being considered a mature technology, even though there are still countless avenues for exploration."

Jan 1, 1998

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By H. J. McQueen

Friction stir welding (FSW) generates complex microstructures in the nugget and thermomechamically affected zones (TMAZ) that have led to diverse explanations. However, consideration as an extension of microstructure development in piercing/extrusion can lead to a better understanding of flow patterns and microstructures during FSW. Furthermore, the intense strains in the nugget/TMAZ can be interpreted by comparison with ultra-high strains in torsion that exhibit dynamic recovery as extending into regions with high angle boundaries strongly serrated with spacing near the subgrain size defined by the high temperature. The subgrain diameter and extrusion pressure have been shown to be dependent on the Zener-Hollomon parameter Z (=t exp(Q/RT), Q activation energy, R gas constant) combining temperature T and strain rate E in the same mariner as for torsion and compression. Moreover, such tests exhibited steady state stress os above a certain strain Es (rising as Z increases) in which T, , subgrain diameter and dislocation spacing remain constant. Due to the subgrain boundaries (SGB, low angle <5°, i.e.,LAB), continually rearranging by migration, decomposition and reformation, the subgrains remain equiaxed in elongating grains, whose boundaries (GB) become serrated as they migrate to absorb SGB. As confirmed by straining in torsion at constant T and Z. , more subgrains bordering the greater GB area have several high-angle facets (HAB) ; these small cellular regions with a mixture of HAB and LAB facets are designated HAB-subgrains. As serrations in neighboring grain boundaries impinge, the grains pinch off becoming shorter; this occurs at higher strains as subgrain size decreases with rising Z. The pinching-off makes the neighbors thicker so the grains never become thinner than about two subgrain diameters. In conjunction with such geometric dynamic recrystallization (gDRX), GB&apos;s undergo a net migration into grains with denser substructure, enlarging those with larger subgrains. Consequently a better name has been proposed: grain dimensioning dynamic recovery (gDRV).

Jan 1, 2007

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texas Gulf Incorporated operates the Kidd Creek Mine, a 10,000 tons per day base metal producer, near Timmins, Ontario. Two different ore types are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall Concentrator the ores are processed by selective flotation in threes individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream x-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8%, zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.INTRODUCTIONSEcstall Mining Limited, a wholly owned subsidiary of the Texas Gulf Incorporated operates the Kidd Creek Mine, one of the world's major base metal producers, near the old gold mining centre of Timmins, Ontario. Discovered in 1964, the property was brought into production in November, 1966. Originally designed for 9,000 tons per day, the operation now treats 10,000 tons per day of two different ore types mined from a single open pit. In the near future, open pit ore will be supplemented by ore from an underground operation now being readied for productionAt the Ecstall Concentrator the ores are processed by selective flotation in three individual circuits. The whole plant is highly automated and control is coordinated from a central control room. The treatment process follows conventional practices although fine grinding is required for optimum flotation recoveries. Normally, two circuits treat copper-zinc ore at a combined rate of 6,500 tons per day while the third circuit treats 3,500 tons per day of silver-lead-zinc ore. Special production averages 2,400 tons per day."

Jan 1, 1973

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

Les Mines Inmet ? La Division Troilus exploite une mine d?or à ciel ouvert depuis 1996 et produit un concentré de cuivre. La Division Troilus est localisée à 175 KM au nord de la ville de Chibougamau? au 51 parallèle.

Feb 1, 2008

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003