Search Documents

By C. A. Olivier

Le Ministère des Richesses naturelles du Québec has continued development work on the process/or direct reaction 0/sodium carbonate with lithium-bearing silicates(Canadian Patent No. 643,843). Recent process improvements have involved continuous pressure leaching, rather than batch leaching, and higher solution concentrations (over 55 g/l Li2CO3. These improvements have been demonstrated on a pilot scale operating on decrepitated spodumene from the Sullivan Mining Group's Quebec deposit. The new process is expected to be very competitive with the conventional sulphuric acid route. The improved flowsheet and main process steps will be described along with pilot-plant results.

Jan 1, 1979

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By E. Fried

Cemented paste backfill (CPB) is an innovative tailings management method that consists in returning considerable amounts of mine tailings into the underground mine openings. The filled stopes thus participate to the ground support that allows maximizing orebody extraction and a safer environment for the mine workers. There are also significant environmental advantages of using CPB. Indeed, up to 50% of the concentrator tailings can be backfilled, leading to a smaller volume of problematic waste materials to be managed at the surface. Once the CPB is placed, or when the mine is flooded at its end-life, the backfill is subjected to underground water flows that may leach and spread the pollutants (mainly metals, sulphates, and acidity) which can contaminate the underground waters. The aim of this study is to characterize the leaching properties of CPB material and to identify the cement phases that ensure the metal fixation. A laboratory procedure was implemented consisting in the preparation of various paste backfill mixtures using sulphide-rich and sulphide-free materials, different types of binder, and mixing waters having various sulphates, copper and zinc concentrations. After 90-days curing time, the samples were submitted to column leaching tests. The CPB materials were flushed each day with 100 ml of deionised water during 100 days. The collected leachates were then analyzed for pH, Eh, electric conductivity and chemical composition. For some samples, a differential acid neutralisation test was carried out. The objective of this experiment is to dissolve selectively the hydrated phases by adding incremental acid concentrations. By analyzing punctually the equilibrated solutions, the composition of the dissolved phases and their metal content can be estimated. The leaching test results showed that the pH of the leachates remains alkaline during the test period. When the pH decreases under 10 (after 30 days), different behaviours in terms of chemical element release (especially for zinc) were observed. During the test, the oxidation of pyrite seems to slow down, probably due to passivating phenomena. Moreover, the differential acid neutralisation test results allowed a better understanding of the CPB mineralogy and the Zn-bearing cement phases. Zinc and the other metals seem to be fixed within a calcium-magnesium silicate.

May 1, 2007

By X. Yuan

"The processing behaviours of ores such as their liberation characteristics in comminution and their response in separation processes are affected by their mineralogical characteristics. Key ore characteristics which are relevant to processing, such as mineral proportions, mineral grain size, grain shape and mineral associations are routinely measured at the micro-scale in polished section using optical microscopes and SEM-based automated mineralogy systems. The application of X-ray micro-tomography to mineral processing provides the means to quantify these important micro-textural characteristics in three dimensions, removing the stereological issues encountered when measuring volumetric information in two-dimensional polished sections. In this paper we present several examples of ore textures to illustrate where X-ray micro-tomography can be applied successfully to obtain quantitative measures of ore characteristics which are useful in a variety of process modelling applications.INTRODUCTION X-ray tomography has been used as a tool in medicine for some years and is being applied in a wider range of fields including geology, palaeontology and mineralogy. In this paper we present some applications of X-ray tomography in mineral processing applications being developed at JKMRC. The availability of SEM-based automated mineralogy systems such as MLA and QEMSCAN has seen the increased use of quantitative mineralogical data measured in two dimensions in the design, operation and simulation of mineral processing plants. When the ore is amenable to measurement by X-ray tomography this technique can provide quantitative data for characteristics such as mineral grain size, shape, mineral associations and liberation in three-dimensions. The advantage of measuring these characteristics in three-dimensions is that the stereological issues which bias measurements made on polished sections are removed. X-ray tomography also quantifies the location of mineral grains relative to one another in space - a useful descriptor of ore texture. Like many measurement techniques X-ray tomography has advantages and disadvantages when compared to other techniques. One limitation is that the ability of the X-ray tomography system to discriminate between minerals is a function of the X-ray attenuation of those minerals. While the X-ray attenuation of many common minerals is sufficiently different for X-ray tomography to distinguish between them, there are some where the overlap in X-ray attenuation makes discrimination on the basis of this characteristic alone impossible. An example of this would be chalcopyrite and magnetite. However where the ore mineralogy is suitable to apply X-ray tomography, the technique provides some exciting opportunities to explore the relationship between texture and ore processability."

Jan 1, 2012

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By J. Hansen

"ABSTRACTThe paper addresses the application of automated monitoring, control, and navigation to improve dragline performance. SummaryImproving dragline performance in the Canadian coal mines is critical to the continued success of the industry. Draglines represent a large capital investment and coal prices are low by historic standards. This paper argues that the introduction of monitoring, control, and navigation on draglines offers an opportunity to significantly reduce a dragline’s operating cost per cubic metre moved. To place the importance of this in perspective, a North Dakota mine calculates that every 1% increase in dragline productivity means a savings to the mine of US$340,000 per year. MonitorsAutomated dragline monitoring is a well established technology with commercial products available since the early 1980s. The three main reasons for placing monitors on draglines are (Walker, 1993):1. productivity increases: reduce variations between different operators’ performance across different shifts;2. quality increases: increase the percentage of ore and waste loads that go to the correct destination; and3. special projects (engineering projects): justify installing static field exciters and regulator upgrades; implement power management; aid operator training; study high performance buckets, rigging changes, and various excavation sequences.Mines as diverse as Kennecott’s Cordero- Rojo Complex in the United States and Natal Coal Corp.’s Optimum Mine in South Africa report dragline productivity increases of 10% to 20% in the region attributed to the implementation of dragline monitoring."

Jan 1, 2000

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By P. Dauphin

"CANMET’s Mining and Mineral Sciences Laboratories have developed the Canadian Mining Technology Network (CMT-Net), a website to provide industry with up to date information on technologies in several areas. This paper gives background on the Mineral and Metal Processing sector, describes the steps leading to the development of the websites strategy and gives a tour of CMT-Net. IntroductionThe government of Canada is developing a strategy aimed at fostering the development of value-added activities in the area of mineral and metal processing (MMP). Natural Resources Canada (NRCan) and Industry Canada will partner in delivering on this strategy. Instrumental in defining the main thrusts of the value-added strategy was a series of consultations held across Canada with representatives of companies and organizations active in the sector. The objective of the consultations was to identify barriers to the development of activities which add value in the sector, as well as point to positive factors.Following the consultations, a discussion paper was produced, “From Mineral Resources to Manufactured Products: Towards a Value- Added Mineral and Metal Strategy for Canada” (Natural Resources Canada, 1998). The paper reviews the sector’s structure and main statistical information, lists some of the positive factors and barriers to value-added activities and defines a new partnership between industry and government that will lead to more valueadded activities. The main objective of the paper is to serve as a discussion document between stakeholders during the development of the strategy."

Jan 1, 1999

By D. A. Rhys, M. Sieb, M. A. Prefontaine, C. L. Swanson, S. R. Frostad, H. Q. Smit

"Gold-silver mineralization at Red Mountain (1992 resource of 2.5 million tonnes grading 12.8 g/t Au and 38.1 g/t Ag) occurs within several discrete zones within a folded sequence of Middle to Late Triassic Triassic sedimentary rocks, Early Jurassic volcaniclastic and pyroclastic rocks, and Early Jurassic intrusions. Three phases of Early Jurassic sills and stocks collectively comprise the Golds/ide intrusions: (1) irregular bodies of medium-grained hornblende monzodiorite (Hillside porphyry); (2) hornblende-biotite + quartz porphyritic monzodiorite to quartz monzodiorite (Golds/ide porphyry; U-Pb zircon ages of 197.1 + 1.9 Ma); and (3) biotite porphyritic hornblende monzodiorite sills (Biotite porphyry). Contact breccias and igneous breccia dikes are common features of the Golds/ide intrusions. Chemical similarities and equivalent ages of volcanic rocks and intrusions, and the presence of intrusive clasts in volcanic rocks suggest that the intrusions are feeders to overlying volcanic units.Hydrothermal alteration affects all pre-Tertiary rocks on Red Mountain, including all phases of the Golds/ide intrusions. Several shallow-dipping alteration zones are developed sequentially above a propylitic quartz stockwork/molybdenum zone. These include: (1) sericite-quartz-pyrite alteration (pyrite-dominant alteration); (2) chlorite-K-feldspar-sericite-titanite alteration with disseminated and vein pyrrhotite (pyrrhotite-dominant alteration); and (3) brown to black tourmaline veins and K-feldspar-pyrite-titanite-actinolite alteration. Anomalous gold(> 0.3 g/t) mineralization is developed at the transition from the pyrite to the pyrrhotite dominant alteration over a > 1 km2 area. Within this anomalous zone, high-grade (3 g/t to 20 g/t Au) gold-silver mineralization occurs in 5 m to 29 m thick, semi-tabular pyrite + pyrrhotite stockworks with intense sericitic alteration and surrounding disseminated sphalerite + pyrrhotite.Stratigraphic, spatial and geochronologic relations and alteration zoning indicate that mineralization formed in a subvolcanic environment at the top of the Golds/ide intrusions and at the base of the Early Jurassic volcanic pile. The Golds/ide porphyry is interpreted to be the mineralizing intrusion. The alteration zoning, molybdenum-copper mineralized quartz stockworks, extensive Ksilicate and tourmaline alteration, and the relationship with a hypabyssal porphyritic intrusion show similarities to many porphyry systems."

Jan 1, 1995

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014