Search Documents

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By H. A. Gorrell, S. R. L. Harding

"The potash beds in the Saskatchewan portion of the Williston Basin occur in the upper portion of the Prairie Evaporite formation of the Devonian Elk Point Group. They represent the late stage of a major evaporitic cycle. Two other evaporitic cycles are known in overlying beds, but these apparently never reached the stage of potash salt deposition. The basin in which salt deposition took place extended from the northwestern corner of Alberta southeastward across Saskatchewan into Manitoba, North Dakota and Montana. Deposition of potash salts was apparently restricted to the southeastern portion of the evaporite basin. On a regional basis, five major stratigraphie divisions of the potash-bearing strata have been made. Locally, several of these units may be divided into correlatable sub-units. The potash-bearing strata are separated and overlain by predominantly halite layers of varying thickness. Cross sections show the regional correlation of the potash-rich zones, and maps show the present distribution of the individual potash-bearing zones and the areas of richer development for each zone. The maps tend to substantiate the interpretation of considerable subsurface solution of salt and potash beds."

Jan 1, 1967

By C. R. Whittemore

IT can be truly stated that no branch of the engineering industry has progressed more rapidly in the last few years than that of welding. In spite of depressed economic conditions, this industry has continued to advance along scientific lines, replacing the old hit-and-miss method of welding. The development work is intensive, and increased activity is recorded in every sphere of the industry, new applications of existing methods, together with new processes, being added to those already proved in practice. The general acceptance of the welding processes can be measured by their utilization as a manufacturing tool in the metal-working industries. Many manufacturers have partially or wholly adopted welding. These concerns have on their staffs welding specialists, design engineers, and metallurgists, who are qualified to design and supervise the manufacture of welded parts, at a considerable saving to the purchaser. The steady, consistent, and sound growth of welding is based upon investigation of the fundamentals of the various processes, together with their proper application. The classification of welding processes varies in different countries. In Europe, they are divided into two main classes, namely, heterogenous and autogenous. In the former, the parts are joined, as a ruler without melting the edges, and by using as filler a metal different from that of the object welded. Such welding differs from soldering and brazing in that higher temperatures are required to effect the union of the parts. In autogenous welding, the parts are joined by melting of the edges, with or without the addition of a material similar to the parts being joined.

Jan 1, 1936

By M. Al-Khawaja, F. Hassani, F. Mucciardi, N. Razavinia

"In today’s economy many industries are becoming aware of the need to recover some of the waste heat they create. Industrial processes release, on a global scale, over 100 tera-Joules (i.e. 1014 J) of waste heat annually. The recovery of waste heat can lead to a reduction of greenhouse gas emissions and it can also provide a financial benefit which can be obtained by converting some of this excess heat to electricity. At McGill, a research program has been initiated so that low grade waste heat (temperature between 100ºC and 300oC) from process off-gases found in pyro-metallurgical industries is captured and concentrated by using heat pipes and then converted to electricity by a mechanical engine. This paper illustrates the 3 C’s process (capture, concentrate and convert waste heat to electricity). It also provides some preliminary experimental data. INTRODUCTIONThe problematic climate change caused by the use of fossil fuels, the rapid depletion of global reserves and the catastrophic consequences of nuclear power generation call for renewable and safe, resources of energy, for both man and the environment. Extensive researches in the production of energy from renewable sources and improvements in efficiency of current technologies can help us to reverse this trend.The greatest advantages of using renewable energies are that they don’t deplete and they also contribute to a green environment. On the other hand the disadvantage of using these resources is that the energy available from renewable sources is much less concentrated than that provided by fossil fuels and nuclear energy. This makes renewable energy less attractive for large scale industrial uses in most cases. A key target for society for the 21st century is the production of energy from renewable sources at a cost that is competitive with fossil fuels. Fossil fuels represent a concentrated form of energy; usually it is referred to as high grade energy. Nonetheless, there is a vast supply of alternative energy. The sun, wind, water and biomass were the first to be explored. While these are all valid options that warrant concerted efforts and large investments, there is another source of energy that typically is produced by manufacturing industries. This energy is often referred to as low grade waste heat. Most of this energy is simply vented to the environment through the stream of off-gases. In the future it will be necessary to capture and convert some of the low grade heat to a valuable form such as electricity if we are to improve on the efficiency of energy usage."

Jan 1, 2012

By D. Yuan, M. Sitter, S. St. Jean, M. Collins

The Ambatovy Joint Venture comprises an operating lateritic nickel mine, ore slurry pipeline, pressure acid leach plant and nickel refinery in Madagascar. The hydrometallurgical process selected by Sherritt for treatment of the Ambatovy ore is a long-term, sustainable approach to producing nickel. Sulphur, used to prepare hydrogen sulphide, which is used to produce mixed sulphide intermediate, is recovered in the refinery as ammonium sulphate fertilizer. Additional sulphur is used to generate sulphuric acid for treatment of the ore in the high pressure acid leach (HPAL) step; fossil fuel consumption is minimized by using the heat generated from the exothermic reaction between sulphur and oxygen in the acid plant to produce power and steam. Steam consumption is minimized by design of efficient flashing and preheat systems for HPAL, while the high temperature of the HPAL step serves to minimize acid consumption. Fossil fuel consumption by the operation as a whole is further minimized by locating the leach plant and refinery near the port of Toamasina and utilizing a 220 km slurry pipeline to transport ore from the mine to the leach plant. In addition, Ambatovy has demonstrated a strong commitment to sustainability programs such as the biodiversity management program at the mine and local procurement in Madagascar. In this paper, the hydrometallurgical process for nickel and cobalt recovery from Ambatovy ore is described, along with highlights of Ambatovy’s approach to sustainability in Madagascar.

Jan 1, 2015

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By A. Roy MacLean

"In the Maritimes, there are twelve coal areas. From east to west, these include the Sydney coal field, the St. Rose - Chimney Corner, Inverness, Mabou, Port Hood, Pictou, Colchester - Debert, Springhill, Joggins - Chignecto, Beersville, Lake Stream, and Minto. The first eight are in Nova Scotia while the remaining four are in New Brunswick.In all these areas, the coal was formed during the Carboniferous period, which existed some 300 million years ago. However, within this period not all coal formation took place during the same time. There were three main intervals, which occurred at the time that the Riversdale, Cumberland and Pictou groups were laid down (Hacquebard, 1970). The oldest coals are those of the Riversdale Group. These coals were of rather limited extent, and only a few mineable seams are present, particularly at St. Rose -Chimney Corner and Port Hood. From these two areas only 2 M tons have been extracted, and 'measured' resources of 7 and 9 M tons respectively remain. The Cumberland Group coals are confined to Cumberland County and include the coals of Springhill and Joggins River Herbert -Chignecto. Some 43 M tons have been removed and only 7 M tons of 'measured' coal remain, with an addit10nal 39 M tons of 'inferred' resources. However, there are additional resources at Springhill, which will be discussed in more detail in a later section. The coals of the Pictou Group are the youngest and the most abundant, both in actual number of seams and in regional distnbution. These coals were formed during the Westphalian C and D, a time during which the main coal deposition in Europe also took place. Here belong the coals of the Sydney, Inverness, Mabou, Pictou, Debert, Beersville, Lake Stream and Minto fields. Their total production amounted to 469 M tons or 91 % of the Maritime total of 514 M tons. The remaining resources of all Pictou Group coals have been calculated at 254 M tons of 'measured' coal and 949 M tons of 'inferred' coal. As can readily be seen, the bulk of both past production and remaining resources occur in the Sydney coal field. The Sydney figures represent 73% of total production, and 87% of total 'demonstrated' resources in the Maritime Provinces. Next to Sydney, the Pictou coal field has been the greatest producer, with 59 M tons; it also has the second largest 'measured' resources, amounting to 25 M tons. However in terms of 'inferred' coal resources, the Mabou coal field, ~ith 140 M tons, ranks second to Sydney."

Jan 1, 1985

By K. A. Clark

A meeting between representatives of the Scientific and Industrial Research Council of Alberta and the Deputy Minister of Mines for Canada was held at Edmonton in May, 1929, for the purpose of formulating a co-operative plan for carrying forward studies in aid of the development of commercial methods for utilizing the bituminous sands of Alberta. It was agreed that to the Alberta Research Council should be allocated the general problem of investigation of the processes for the separating of bitumen from the sands, including studies of methods of emulsifying, dehydrating and otherwise preparing separated bitumen for industrial applications. It was further agreed that during the present year the work of the Alberta Research Council should be to continue its laboratory investigations of points of design of its separation plant; to further perfect its separation procedure; to recondition its existing separation plant at Dunvegan Yards, Edmonton, in the light of laboratory studies and to operate it for the purpose of demonstrating its efficiency; to carry on tests in emulsifying and dehydrating or otherwise preparing separated bitumen for industrial application; and on the basis of the experience gained in the operation of the preliminary plant at Dunvegan Yards to prepare and design and, as far as possible, to proceed with the erection of, a semi-commercial separation plant at a site to be chosen, probably at the bituminous sand deposits near McMurray, Alberta. This paper presents, in the main, a progress report of the carrying out of this programme.

Jan 1, 1929

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review&apos; of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff&apos;s review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

"3.1. IntroductionAmong the six platinum-group elements (POE), four have identical cubic symmetry, two identical hexagonal symmetry (Table 3.1). Despite crystallographic differences, there is a clear relationship expressed in the chemistries of the POE: they tend to be mutually soluble in one another and can frequently substitute for one another in compounds with other elements. This chapter consolidates the data on phase relations of the POE and the compounds they form with elements selected for their known or potentially important mineralogical significance- As, Bi, Cu, Fe, Hg, In, Ni, Pb, S, Sb, Se, Sn and Te-together with selected data for the occurrence of POE in certain elements such as Au and Ag, and compounds such as FeS. Resources used to compile the data are those available from the chemical, mineralogical and metallurgical literature. First each element is discussed, with composition limits of solid solutions drawn from binary phase diagrams. Single element data are followed by a discussion of the relevant binary systems and a tabulation of data for binary compounds found in those systems (Table 3.2). Tables and diagrams for the ternary and quaternary systems for which information is available follow, and finally the very limited information on the solubility of POE in mineralogically important elements and compounds is presented.The chemical, mineralogical and metallurgical literature on the unary and binary systems is extensive and widely scattered in many languages and publications; fortunately, most of the data needed to compile this chapter can be found in reliable compendia. The most useful and most recent of these works is by Moffatt (1979), because it provides a ready index to all material relating to binary systems listed in previous compendia; furthermore, the Moffatt compendium will reportably be kept up to date by annual supplements."

Jan 1, 1979