Search Documents

By D. Beneteau, D. Milne

"Advances in technology provide educators with valuable tools to enhance their teaching and efficiently deliver content to larger audiences. University educators are often encouraged to become more “research intensive” and to increase student enrollment. Faced with these pressures, there is a tendency to use technology to improve teaching efficiencies rather than to enhance existing teaching approaches. Practical learning in applied engineering courses would suffer greatly if hands-on experience is not emphasized. This paper discusses advantages and limitations of new technologies applied to learning, and methods to incorporate more hands-on experiential teaching techniques to applied mining engineering courses.RÉSUMÉ Les avancées technologiques fournissent aux éducateurs des outils intéressants pour rehausser leur enseignement et livrer efficacement de la matière à de grands auditoires. Les éducateurs universitaires sont souvent encouragés à devenir plus « axés sur la recherche » et d’augmenter l’inscription d’étudiants. Face à ces pressions, il y a une tendance à utiliser la technologie pour améliorer l’efficacité d’enseignement plutôt que de rehausser les approches existantes d’enseignement. L’apprentissage concret dans les cours d’ingénierie appliquée souffrirait grandement si l’accent n’est pas mis sur l’expérience pratique. Le présent article discute des avantages et des limitations des nouvelles technologies appliquées à l’apprentissage et des méthodes pour incorporer plus de techniques expérimentales pratiques aux cours de génie minier appliqué."

Jan 1, 2016

By L. Chunpongtong

ABSTRACT The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By L. Chunpongtong

The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By P. J. Bourassa

Incorporated in 1957 under the laws of the Province of Quebec, Quebec Cartier Mining Co. undertook the development of its low-grade iron ore reserves located at Lac Jeannine in the southwest extremity of the Quebec-Labrador trough. This challenge comprised the construction of a 200-mile access road, two towns, a 191-mile-long railroad from Port Cartier to Lac Jeannine, a hydro-electric generating plant on the Hart Jaune River, and mining, crushing, concentrating and ancillary facilities to support a yearly production of 8.0 million tons of iron ore concentrates at 66% Fe. In order to meet increasing market demands for iron ore concentrates concurrently with the depletion of its Lac Jeannine reserves , Quebec Cartier announced, late in 1969, the first step toward bringing into production a new iron ore deposit, known as Mount Wright, located 70 air miles northeast of Lac Jeannine and 25 miles southwest of Labrador City, Newfoundland. In September 1970, the company announced its decision to develop and bring into production its Mount Wright reserves at an annual rate of 1 8.4 million dry long tons. The scope of this project included the construction of an access road linking the mine, the new town and Labrador City, Newfoundland, the extension of the railroad by some 86 miles, the construction of an ore concentrating plant with all the ancillary facilities, the development: of the mine, the construction of a pourer transmission line and a new town adjacent to Lake Daviault. The Mount Wright story is divided into five individual papers covering: (a) the history and development of the project; (b) the mine; (c) plant control by a process computer; (d) crushing, grinding and concentrating; and (e) the townsite of Fermont.

Jan 1, 1977

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06' N, long. 42°40' E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By W. Noel O?Brien

Introduction Since 1930 numerous improvements have been made in equipment designed for the mechanical removal of broken ore in underground mining operations. New applications of mechanical equipment, as? well as improvements and adaptations of well established systems, are being made continually. It is the purpose of this paper to discuss present-day equipment for the removal or transfer of broken ore by means of a powered hoist and scraper arrangement. The terms used throughout the paper are those commonly employed in the trade literature and by mining men. The terms slusher hoist, hoist, and scraper hoist are used inter-changeably to mean a machine, powered by compressed air or electricity, with drums for the winding of wire rope. The tail rope, also known as the pull-back rope or return rope, drags the empty scraper toward the tail-sheave, that is, back to the loading point. No attempt is made to cover the entire field of application of scraping methods. Rather it is the? writer's desire to emphasize the fundamental principles of scraping practice and design and to relate them to some modern applications. The available literature on scraping practice has been freely used. together with personal observation and information and advice of practising engineers and representatives of companies manufacturing slushing equipment.

Jan 1, 1951

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By A. G. Roach

Introduction This paper deals with the operations and plant of the Craigmont Corundum Project, formerly of Wartime Metals Corporation but now under the Mines Section of the Resources Development Branch of the Department of Reconstruction and Supply. Corundum is recovered by the re-treatment of an old tailing deposit at Craigmont, Ontario. Crude concentrates so produced are shipped to the plant of the American Abrasives Company, Inc., at Westfield, Mass., for final processing and distribution to the abrasive industry. The plant was recently described in a paper entitled Craigmont Corundum which was presented by the writer before the Chicago meeting of the A.I .M.E. in February, 1946. General The Project is located on? lots 4 and 5, concession XVIII, township of Raglan, Renfrew county, Ontario, near the village of Combermere, which is on Highway 62. The property is about 135 miles from Ottawa. The general area enjoys a pleasant climate with moderate summer temperatures, though the winters are rather severe, the mercury frequently falling to - 35 deg. F. The excellent boating, fishing, and hunting have made the district a favourite resort for tourists. Lumbering is the main industry. Some farming is carried on, but the soil is poor and much of the land is hilly and rocky. There are no other operating mines in the immediate vicinity, though several 'industrial minerals', including mica, feldspar, nepheline, beryl, socialite, and others have been produced in the area. The district is drained by the York and Madawaska rivers and is generously dotted with large and small lakes. The general elevation is about 1,000 feet above sea level, though numerous hills rising several hundred feet give a rolling appearance to the landscape.

Jan 1, 1946

By R. H. Beaton

"About 1905, a plant was constructed at C1ayburn, in the Lower Fraser valley, 4'5 miles east of Vancouver, to process shales from Sumas mountain into heavy clay products. In time, mining operations were found to be more favourable on the opposite side of the mountain, and by 1913 a plant, which soon became the centre of activities, was completed at Kilgard. Destroyed by fire in 1949, the plant was rebuilt on modern lines, and a second plant was established at Abbotsford, six miles to the west. The Company, from its beginning, has grown with development of the Province. In recent years, operations have kept abreast of latest developments, particularly in materials handling. Latest innovation has been the complete conversion of fuel from Bunker C oil to natural gas. In 1957 the Company became associated with Harbison Walker Refractories, Limited, a leader in its field in the United States, and its title was changed from Clayburn Company, Limited, to Clayburn-Harbison, Limited. Currently, the Kilgard plant produces sewer pipe, agricultural tile, and flue liner; the Abbotsford plant, refractories and facebrick. Improvement of products and development of new ones are tasks of a recently-completed testing and research laboratory.Almost all ware produced is marketed in Western Canada or Washing-ton State. The Vancouver area absorbs the bulk of structural clay products."

Jan 1, 1959

By Victor Dolmage

Introduction Although gold production in British Columbia began in 1859, lode gold was not produced till 1893. Since 1900, the annual production of lode gold has fluctuated between $3,000,000 and $6,000,000. About twenty per cent of this production may be regarded as by-product gold from base metal mining. The remainder comes from a few isolated but important mines, such as the Rossland mines, Nickel Plate, Surf Inlet, Premier, Pioneer, Bralorne, Reno, and Cariboo Gold Quartz, and from several less important mines. All of the above, except Pioneer, Bralorne, Reno, and Cariboo, are approaching or have reached the point of exhaustion, but all are now receiving, under the stimulus of the. present gold-mining boom, drastic resuscitative treatment, with, in some cases, signs of resurrection. Notwithstanding this, however, the main interest at the present time is focussed on the Bridge River and Cariboo fields. Both these fields were discovered in the early 'sixties' and, apart from the Cariboo placer production, both have from time to time contributed small amounts of lode gold; but it is only during the last two years that the real possibilities of these areas were discovered. and that they began to assume the appearance of goldfields of major importance. The two fields are sorme three hundred miles distant from one another and contain deposits of distinctly different types, so that the only reason for including them in one article is the fact that they came into prominence more or less simultaneously and at a time coinciding with, but not otherwise related to, the present gold-mining boom.

Jan 1, 1934

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental 'evidence' found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000