Search Documents

By C McGuire, W Harris, S Arsenault, D Witow, B Rogers

Mining deep orebodies is increasingly becoming the norm as the ‘easy’ orebodies are depleted. Deep ore mining requires significant ventilation and cooling infrastructure to not only meet regulatory requirements for air quality but also to achieve acceptable workplace temperatures with the higher strata rock temperatures and increased auto-compression. At the same time, advances in battery equipment technology are turning the possibility of a battery powered fleet into reality. The switch from a diesel fleet to a battery powered fleet offers several positive opportunities for the design and operation of a deep mine.The potential to reduce ventilation and cooling requirements due to battery powered equipment results in significant cost savings for mine development and infrastructure. Battery powered fleets are not subject to the same dilution requirements associated with diesel fleets thus allowing lower ventilation rates. At the low ventilation volumes possible with a battery powered fleet, surface refrigeration plants are limited with respect to the amount of cooling that can be delivered to the workface. Considerations for calculating the optimum air flow and cooling requirements are presented. Considerations for locating the refrigeration plant are also discussed. This paper presents these opportunities and considerations; including a case study comparing the ventilation and cooling system design with a diesel fleet versus battery fleet for a planned mine in Northern Ontario, Canada.CITATION:Harris, W, Arsenault, S, McGuire, C, Rogers, B and Witow, D, 2017. Diesel to electric – creating a positive paradigm in underground ventilation and cooling, in Proceedings Australian Mine Vent Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C E. J de Ronde, J G. Scott

Economic gold mineralisation was discovered at Round Hill by Homestake NZ Limited in 1984 and was subsequently put into production by Macraes Mining Company Limited (MMCL) in 1990. The total mineral resource in 1990 was estimated at 41.4 Mt @ 1.42 glt at a 0.7g/t cut off, for 1.8 Moz of gold. Since project start up the mill has been upgraded twice to increase throughput and reached its current capacity of 3.2 Mtpa. At 31 December 1996, a total of 16.2 Mt of ore at average grade of 1.73 g/t has been excavated, yielding 655,000 oz of gold. MMCL began exploration along the Hyde Macraes Shear Zone in 1994. Since 1994, exploration has been successful with the discovery of over 3.5 Moz of gold. The resource now stands at 110 Mt @ 1.46 g/t gold for 5.1 Moz. This success has led to a planned expansion of the processing capacity to 9 Mtpa with the building of a new 6 Mtpa processing plant.

Jan 1, 1997

Beneficiation Studies of Dolomitic Rock Phosphate in Pursuit of Zero Waste Technology - A Case Study

Sep 13, 2010

By H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in southern Perú and the northern Chile coastal IOCG belt have emerged as two of the major exploration targets in the Central Andes in the last two decades. These Mesozoic Andean IOCG deposits formed in two mineralisation epochs, the Middle-Late Jurassic (170–150 Ma) and Early Cretaceous (130–110 Ma), with the major Cu-rich IOCG deposits located in the Early Cretaceous mineralisation belt. The early studies in some IOCG centres support a magmtic-hydrothermal model for both Cu-rich IOCG deposits and broadly contemporaneous Cu-poor ‘Kiruna-type’ magnetite deposits. However, recent evidence from field, geochronology, fluid inclusions and stable isotopes show that in the major Central Andean deposits (eg Raúl-Condestable, Mina Justa in southern Perú, La Candelaria-Punta del Cobre and Mantoverde in northern Chile), the incursion of evaporite-sourced basinal brines or sea water may be a prerequisite for economic Cu mineralisation. Moreover, the Cu-poor massive magnetite deposits could be interpreted as a product from iron oxide melt, with minimal intervention by non-magmatic fluids. Therefore, they could represent two contrasted deposit types and contain little genetic relationships. The different roles of magmatism during the Mesozoic are responsible for the variable mineralisation in the Central Andes, including IOCG, magnetite and ‘manto-type’ deposits. The ore modelling for both the Middle-Late Jurassic and Early Cretaceous metallogenic epochs in the Central Andes are reconstructed.CITATION:Chen, H, 2015. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in the Central Andes – a refined IOCG ore-forming model in the Palaeozoic Continental Margin, in Proceedings PACRIM 2015 Congress, pp 251–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C Katonga

Mindola mine is currently the deepest mine in the Zambian copper belt. Stoping is currently active to 1330 m below surface with long range plans indicating future production from 1590 m level. The orebody is tabular and dips between 55o to vertical. The thickness varies from 8 to 14 m. The vertical crater retreat method of mining was first introduced at Mindola mine in the late-1980s following several trials that helped define the design criteria for its application. Over the last ten years the method has been continually modified to improve safety and maximise ore production. For example, due to the weakness of some rock units within the orebody formation and the instability of the hanging wall, the last VCR slices are usually between 8 - 10 m thick, and efforts are being made to strictly apply shrinkage method in order to reduce dilution. Recent advances in mining technology in the areas of equipment, blasting techniques, rock mechanics and materials handling have been employed to increase the overall productivity of the mine. Large down-the-hole machines capable of drilling 165 mm diameter blast holes, up to 80 m long are used in stoping. Each stope produces up to 20 000 tonnes of ore per month and can last for three months. Heavy systematic ground support of VCR development has significantly enhanced safety for mining crews and equipment. Crater mining has not only improved productivity and enhanced safety, but also overcome various problems associated with conventional sublevel open stoping previously employed at the mine. This paper discusses the technical and operational aspects of vertical crater retreat mining at Mindola mine during the last ten years. The changes in mining method are often accompanied by changes in mine design, blast design, mining equipment, ground support and operating practices.

Jan 1, 2000

By T Harding, T Riggs, D Taylor

High-grade hematite ores in the Hamersley Province of Western Australia are associated with hydrothermal magnetite-apatite and magnetite-hematite-carbonate-apatite proto ores below the modern weathering surface. In addition, hydrothermal alteration of country rocks, once believed to be absent, is now recognised widely in shales and dolerites up to several hundreds of metres away from the ores. Both observations appear to exclude a simple supergene model for ugrading the host iron formations to high-grade hematite ore. Similar hydrothermal proto ores and country rock alteration are now being recognised in other high-grade hematite deposits worldwide, or have been recognised in the past.

Jan 1, 2002

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By T M. El Hajj, A C. Chieregati, M T. G C Marques, J M. Braga Jr, H Delboni Jr

"The estimate and control of sampling errors is essential for all mining operations, especially when dealing with strategic materials, such as niobium. This paper is based on a traditional quality assurance and quality control technique used to confirm mineralised intersection zones, and proposes the validation of sampling data using diamond drill twin holes, in order to evaluate and improve the quality of the current data set. The geological model of the niobium mine – located in Araxá, Minas Gerais, Brazil – was built including 77 diamond drill holes of a sampling campaign carried out during the 1970s. There are few records about the collection and preparation procedures of these past samples, making it difficult to estimate the errors associated with their analytical results. Therefore, 11 twin drill holes were drilled to compare their samples against the samples from the 1970s drilling campaign. The new hole locations were chosen as near as possible to the old holes location. The JORC Code, 2012 edition, relates the use of twin holes as a good sampling technique to assess sampling and assay data. Three parameters were considered to validate the 1970s drill hole campaign by the twin drill hole campaign: the difference of the coordinates between the paired holes the difference among the positions of the geological contacts to validate the geologic description the difference between the paired samples grades was calculated to validate the analytical results.The analysis of the grade range variation between sample pairs was based on three techniques: geostatistical interpretation of vertical semivariogram to obtain the nugget effect calculation of the relative difference between duplicates calculation of the error associated with the sampling protocol established according to Pierre Gy’s Theory of Sampling.The results were satisfactory for hole coordinates; however, the ore content showed a high deviation, although this divergence can be explained by the nugget effect. For the lithological intervals, the new results contributed to an effective identification of variations among lithologies, ie brown weathered ore and saprolite. The twin drill holes campaign successfully validated the geological model data, allowing effective mine planning and higher reliability of the reconciliation results.CITATION:Marques, M T G C, El Hajj, T M, Braga Jr, J M, Chieregati, A C and Delboni Jr, H, 2017. Theory of Sampling and geostatistics for twin drill holes analysis in a niobium mine in Araxá, Brazil, Australia, in Proceedings Eighth World Conference on Sampling and Blending, pp 97–106 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By D Ford

BHP BillitonÆs new rotary iron ore car dumper installation at Finucane Island (Port Hedland) was constructed to increase the total capacity of the port facility from 110 Mtpa to 120 Mtpa and to allow for incremental capacity increases in future. The arrangement of the dumper is similar to other car dumper installations existing on site. To construct the facility, approximately 120 000 m3 of material was excavated in six months, to a total depth of 22 m. The saline water table was nominally 6 m below ground level and the materials excavated varied depending on depth, ranging from sand to mangrove muds. There was a need to retain the sides of the excavation and limit the amount of water from entering the excavated area. This was required to allow excavation to progress and had to be maintained during construction of the permanent concrete and steel facility. The excavation was backfilled progressively as construction progressed. Various retaining wall methods were investigated with the preferred option being sheet piles secured by walers and ground anchors. Detailed electronic models were developed and assessed to complete the final design arrangement. Dewatering bores around the perimeter of the excavation removed the groundwater to intercepted sumps within the site. A strict and methodical program was developed to monitor the integrity of the temporary works and the quality of the groundwater. The works were completed on time despite the following challenges being encountered: availability of resources and equipment, movement of mobile plant on æboggyÆ materials, difficulty driving sheet piles into material at depth, drilling of ground anchors to 32 m, grouting of ground anchors, greater than expected groundwater flows, and the risk of hydrocarbons within the groundwater. The lessons learned from the use of the retention system and, in particular, the associated construction challenges overcome, provide a sound basis for similar work in this buoyant resource market. The conference paper describes the temporary works options investigated, design considerations and processes, construction methodology and challenges encountered, and the monitoring systems developed. Lessons learned are also discussed.

Jan 1, 2007

Study on a Novel Polymer/Bentonite Compound Adsorbent for Removal of Cu(II) from Aqueous Solution

Sep 13, 2010

Frothing in Seawater Flotation Systems

Sep 13, 2010

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Rizzardi, M Callahan, J Mahon

Henderson Operation’s underground molybdenum mine has been in production since 1976. Since that historic date, more than one billion pounds of moly has been produced, and over 120 Mt of ore extracted from three different levels and many different panels. The safe and successful operation of Henderson has been, and will continue to be, dependent on utilising an increasingly sophisticated fleet of equipment, advanced designs, innovative mining techniques, best practices in maintenance processes, improvements in crushing and conveying systems, and most importantly, the training and mentoring of the underground staff. These ‘professional mining technicians’ have been essential in the safe and efficient operation and maintenance of the underground mine and convey systems, and will drive the continuous improvements needed to keep Henderson competitive in the growing global market.CITATION:Callahan, M, Mahon, J and Rizzardi, C, 2016. Development of the professional mining technician – Henderson’s underground mine continuous improvement program, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By S Morgan, A Jakowetz, S Taylor, B Weekes, S Litson, P Bourke, T L. Do

In the current tough mining environment with lower commodity prices, operators need to improve operational profitability. Optimised equipment asset management is a sustainable way to achieve this objective. The increased efficiency of installed process equipment positively contributes to the circuit performance, affecting metallurgical performance, plant availability and operating costs. Nui Phao Mining Company Limited (NPMC) operates a polymetallic mine located in Vietnam. The circuit produces four main products, tungsten, fluorspar, bismuth and copper. Tungsten is the major revenue producer. The operation experienced the following equipment inefficiencies in its copper and bulk sulfide flotation (BSF) circuits:• lower than expected metallurgical performance - the BSF rougher flotation tails contained coarse (+106 µm) sulfur minerals which affected the downstream tungsten gravity circuit. The unrecovered sulfur competed with tungsten minerals affecting both tungsten recovery and product grade. • structural integrity and safety - the flotation circuit structures experienced excessive vibration beyond the acceptable tolerance levels. The vibration was attributed to the flotation mechanism design and impeller tip speeds. • equipment reliability and wear life issues - the flotation mechanisms were being replaced every six months, with reported failures at three months. This resulted in high operational costs. A mineralogical evaluation of the ore indicated that the coarse sulfur minerals were well liberated and relatively rich in pyrrhotite and pyrite. It was predicted that these particles should be recoverable by flotation under optimum conditions. NPMC worked collaboratively with Outotec to investigate options to improve the metallurgical performance of both sulfur and tungsten. A review of the copper and BSF rougher circuit infrastructure was also undertaken and focused on reducing the structural vibration and improving mechanism wear life. Prior to the circuit upgrade, laboratory and pilot testing was conducted to validate the circuit improvements. The final solution included the installation of Outotec FloatForce® mechanisms in the existing copper and BSF rougher circuits, and a new flash circuit (SkimAir®) treating the rougher tails stream ahead of the tungsten gravity circuit. The flash circuit is unique, as typically these types of cells are installed in grinding circuits. By March 2016, all circuit upgrades were complete, however the initial metallurgical performance was below expectations. NPMC and Outotec worked together to investigate and improve performance through further equipment modifications. Since October 2016, the metallurgical performance has improved significantly. Coarse sulfur mineral recovery has improved, resulting in an overall increase in recovery of sulfur and tungsten of 4.7% and 2.7% respectively. The Outotec FloatForce mechanism has also delivered operational benefits, with a reduction in structural vibration to within acceptable levels (<4.0 mm/s) and an improvement in mechanism wear life by 150%. This paper discusses the BSF circuit upgrades and compares operational data before and after the upgrade to quantify the improvements in metallurgical performance, structural vibration and mechanism wear life. CITATION:Morgan, S, Weekes, B, Jakowetz, A, Litson, S, Taylor, S, Do, T L and Bourke, P, 2017. Nui Phao mine – flotation circuit upgrade, in Proceedings MetPlant 2017, pp 230–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The work to be described is part of a comprehensive research on the influence of impurities on the properties of lead. The author had previously compared an electrolytic lead containing less than 0.002% total impurities with a commercial lead containing 0.008% impurities (excluding oxygen) and had shown that the former recrystallised more readily than the latter under the same conditions of cold work and annealing. This difference in properties was attributed to the difference in purity. Electrolytic lead containing only 0.0005% total impurities has been prepared and cast in vacuo. Some interesting effects have been obtained by working and annealing this lead, and by adding silver to it. The preparation of this lead, and the effects obtained thereon, are described in this paper. Thepaper is divided into the following sections:(I) Preparation of electrolytic lead.(II) Vacuum Casting.(III) Effect of Cold, Work and Annealing on two Electrolytic Leads, having 0.002% and 0.0005% Total Impurities respectively.1 Research Fellow, Dept. of Metallurgy, University of Melbourne.2 Proc. Aust. lnst. Min. Met., 1932, 87, 145.

Jan 1, 1934

By A S. Derrington

There are several long-standing rules of thumb that are often quoted in mine ventilation studies. They include airway ‘carrying velocities’ and the critical upcast air velocity range that must be avoided to prevent a water blanket forming. Quoting these rules of thumb may lend an air of legitimacy to a ventilation design, and allow the design engineer to avoid having to study a problem from first principles. But how valid are these shortcuts in today’s rapidly changing world? This paper summarises research into the genesis of several commonly quoted rules of thumb. It finds that they were very specific to the local conditions, practices and economics at the time they were developed. It also presents examples where applying these rules of thumb outside of their original context can lead to unexpected and erroneous results.CITATION:Derrington, A S, 2017. Ventilation rules of thumb – friend or foe? Focusing on design upcast air velocities for shafts and raise bores, in Proceedings Australian Mine Vent Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017