Search Documents

By K. C. Mills, E. T. Turkdogan

The results on the rates of vaporization of Fe-Ni alloys, levitated by an electromagnetic field in a stagnant atmosphere of helium, are shown to be in close agreement with those predicted theoretically. AS shown in Part I of this series of papers, the rates of vaporization of metals enhanced by convection currents are increased further by the process of condensation of metal vapor when there is a steep temperature gradient in the boundary layer. At the time this theoretical work was completed one of the authors (K. C. Mills) had already carried out some experimental work on the rates of vaporization of molten Fe-Ni alloys. The experimental work was done under conditions which make it possible to compare the experimental rate data with those predicted on theoretical grounds. EXPERIMENTAL The object of the experiments was to evaluate the activities in a number of binary metal systems. The details of the experimental technique are given in another paper by Mills, Kinoshita, and Grieveson,2 and, for the present purpose, a brief mention of the relevant features of the experimental method will be adequate. Using an induction coil, the metal weighing about 1 to 1.5 g was levitated by the electromagnetic field in a stagnant atmosphere of pure helium. The helium was freed from oxygen and water vapor in the usual manner, and its pressure in the vaporization chamber was maintained at 1 atm through a bleeder device. The vaporization chamber consisted of a pyrex tube, 2.8 cm diam, with a side arm connected to the helium bleeder. The bottom of the tube, shaped conical, was surrounded by the induction coil, and the top was sealed with an optical flat for the purpose of measuring the melt temperature with a two-color optical pyrometer. By suitable adjustment of the high-frequency power input, the metal was brought to the desired temperature in about 30 sec of levitation. After a specified vaporization time, e.g., 3 to 4 min, the alloy was quenched by switching off the power. The amount of metal vaporized was determined from the difference between the initial and final weights of the sample. During the vaporization time, temperature fluctuations of about ±10°C were observed. COMPARISON OF EXPERIMENTAL DATA WITH THEORETICAL VALUES The experimental results are given in Table I. As already mentioned, the attainment of the vaporization temperature took about 30 sec from the moment of levitation. Therefore, the times recorded in Table I are 30 sec less than the total time; this is considered to be a reasonable estimate of actual vaporization times.

Jan 1, 1964

By H. G. HYMER

B ECAUSE of its remote geographical position and inaccessibility, little is generally known of the mining and prospecting in Northern Rhodesia. In this rather new and promising region, the development of mines presents many difficulties. Although many mineral discoveries have been made, progress in .prospecting the huge mining concessions has been handicapped by the lack of roads, communication, transportation, native population and incomplete knowledge of geology.

Jan 1, 1929

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By William L. Payne, Edward E. Ives

A unique feature of Potash Co. of America's A new potash property near Saskatoon, Sask., is the use of semi-dome-shaped buildings for product storage. Four domed structures, timber-framed and corrugated-sheet covered, are being built; each designed to handle 20,000 cu yd. The relatively small capacity units, PCA believes, give flexibility not only in storing different grades and sizes of product, but also in permitting greater ease in shipping products as market demands change. The domed buildings are 150-ft diam, comprised of a 16-ft-high concrete wall base, topped with a metal sheet-covered octagonal timber frame. The dome of each unit is designed to fit very closely the angle of repose of the contained material, which results in the maximum usable volume. The entire roof is flood coated with a bitumin to provide a complete weather seal.

Jan 9, 1959

By Mason J. Christner

Geology has become increasingly quantitative in the last 20 years. This trend has been accelerated by computer capability in the manipulation of data. The mining industry has been relatively slow to harness computer power, but the larger companies have moved in this direction in the past few years. Among the leaders in this progression is the White Pine Copper Co., and the following is a brief description of their computer system for processing, managing, and utilizing geologic data. Geology The White Pine mine is in the Upper Peninsula of Michigan, 6 miles south of Lake Superior and 80 miles west of the Houghton-Hancock area, center of the famous Copper country. The ore body of chalcocite, native copper, and minor native silver, is a tabular body in the basal 25 ft of the flat lying Nonsuch Shale and the top part of the underlying Copper Harbor Conglomerate. Twelve or more

Jan 1, 1972

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By K. T. Aust

The occurrence of annealing twins in high-purity aluminum resulted in the formation of grain boundaries having orientation relationships which correspond to a high density of coincidence sites. The results provide support for the coincidence site model and indicate that large-angle coincidence boundaries have lower free energies than large-angle noncoincidence boundaries. Observations are presented concerning the coherent structure of twin interfaces in aluminum and the importance of inter-facial energy in preferred orientation. RECENT experiments1 have shown that when an annealing twin is formed during grain boundary migration in zone-refined lead, a large-angle random boundary is replaced at the growth front by a large-angle coincidence site boundary. The coincidence site orientation relationships obtained by twinning were of the type considered by Kronberg and Wilson,2 Frank,3 and Dunn.4 On the basis of the theory of annealing twins advanced by Fullman and Fisher,5 these observations indicate that the energy of a coincidence site boundary is less than the energy of a random boundary by an amount which exceeds the energy of the coherent twin boundary. This energy difference between the coincidence and random boundaries must be at least about 5 pct since the ratio of twin boundary energy to grain boundary energy in zone-refined lead is 0.05 * .014.6 Fullman7 has found that the twin boundary energy in aluminum is about 21 i 5 pct that of a large-angle grain boundary. A twin boundary energy as large as this would be expected to exclude the formation of many coincidence site grain boundaries, especially those which have a relatively low density of coin- cidence sites. Therefore, if the coincidence site model is a useful interpretation of certain large-angle boundaries, then it would be predicted that only coincidence boundaries which separate adjacent crystals with a relatively high density of coincidence sites may be obtained as a result of twinning in aluminum. The present experiments provided a means of testing this prediction since annealing twins occurred during the growth of recrystallized grains into striated, melt-grown single crystals of zone-refined aluminum. EXPERJMENTAL PROCEDURE A striated single crystal of zone-refined aluminum, about 1 cm sq and 37 cm in length, was obtained during zone melting of aluminum of 99.996 wt pct starting purity in a graphite boat under helium atmosphere.8 A molten zone of 2 to 3 cm in length, which was maintained by induction heating. was passed along the length of the bar for eleven passes at a rate of 0.9 mm per min. An additional final pass was given at a rate of 0.2 mm per min. The center portion of the zone-melted bar was characterized by an electrical resistivity ratio between room temperature and 4.2° K of 8000 to 9000. Single crystals of 1 to 2 cm in length were removed from the center section of the zone-refined bar and electrolytic ally polished in a 2:l solution of methyl alcohol and concentrated nitric acid. The specimens were then chemically polished in Alcoa R-5 solution. X-ray analysis of the single crystals indicated the presence of striations or lineage substructure having misorientations as high as 2 deg. New, recrystallized grains were introduced into each striated crystal by the technique of artificial nucleation and growth, previously described.9 During the growth of the recrystallized grains at 300' to 600°C in argon, it was sometimes found that a

Jan 1, 1962

By Paul M. Tyler

MILITARY power stems from industrial power and industrial power in turn depends predominantly upon an ample and assured supply of mineral raw materials. It thus becomes the duty of mineral economists to collate the vast array of data and logical deductions in order to reach an unemotional judgment as to the ability of the Soviet economy to withstand the strain of prolonged military action on the modern scale. Russian publications, reports: and official speeches have been laboriously screened and analyzed. Since these are the sources of information for the lower echelons of the Soviet industrial organization itself, they carry factual data that can be pieced together to show the present-day pattern. Apparent contradictions and obvious distortions or omissions can often be rationalized on the basis of observations made by foreign engineers and consultants during the 1930'5 and by checking against the technical literature published before even so-called technical articles were riddled by bombastic and presumptuous claims.

Jan 6, 1951

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By D. S. Flett, A. W. Fletcher

Equilibrium studies on the extraction of nickel and cobalt with kerosine solutions of naphthenic acid have shown that an exchange extraction reaction occurs at pH 5.5. The nickel/cobalt separation factor is constant at 1.8 for constant total metal molarity and varying nickel/cobalt ratios. The separation factor decreases with increasing total metal molarity in the organic phase beyond 0.2 M and also decreases with increasing temperature. From the equilibrium data, it has been possible to derive a mathematical model for the separation of nickel from cobalt by exchange extraction in multistage systems. Experimental data from a continuously operated multistage mixer/settler apparatus has shown a reasonable correspondence with computer-calculated data. The effective separation of nickel and cobalt in sulfate solution remains a problem in hydrometallurgy and the hope that this would be solved by solvent extraction has not yet been fulfilled. With chloride solutions, advantage may be taken of the ability of cobalt to form anionic complexes with the chloride ion. It can then be readily separated from nickel, which does not form stable chloro complexes, by extraction with a suitable long chain amine. However, in hydro metallurgical operations, sulfate solutions are generally obtained in which no extractable anionic species are present. Thus, the possibility of using cationic extractants must be considered, and in this paper attention is directed to the use of carboxylic acids. The method of separation studied has been termed exchange extraction, which involves replacement of a metal in the organic phase with a more acidic metal in the aqueous phase. Thus, (BR2).+ (Az+)aqt=(AR,).+ (B2+)aq (I) where metal A is more acidic than metal B, R represents the acidic radical derived from the acid RH, and the subscripts e and aq refer to the organic and aqueous phases, respectively. Ashbrook and Ritcey' have used this method for the separation of cobalt from nickel using the sodium salt of di-2 ethyl hexyl phosphoric acid, which preferentially extracts cobalt. Some nickel is coextracted, and this is removed by exchange with cobalt ions in the feed solution by suitable countercurrent operation in a pulsed column. Much work has been carried out by a number of workers in Russia on the general use of exchange extraction for the separation of metal ions using car-boxylic acids. Gindin et aL a have demonstrated that this technique could be applied to the separation of nickel from cobalt using a C--C. carboxylic acid and have applied the technique to the production of high purity cobalt solutions for electrolysis. Further worka was concerned with the development of a process for the separation of nickel from cobalt in a pulsed column. This system permitted the separation of iron and copper from nickel and cobalt in one system. The procedure involved center feeding with acid backwashing at the top and alkali addition lower down the column. Thus the system operated under a pH gradient and the metals were distributed in the column in the order of their basicities. A similar application was studied by Gel'perin et al,4,5 for the removal of copper and iron impurities from a nickel anolyte by means of a C10-C,12 fatty acid fraction. Ginden et al,' and Fletcher and Wilson' have studied the effect of pH on the extraction of a number of metals with carboxylic acids. These studies showed that metals such as iron, copper, lead, zinc, nickel cobalt, and manganese are extracted at pH values close to the pH of hydroxide precipitation. Nickel is extracted at a slightly lower pH than cobalt and thus the nickel/cobalt separation factor has a value not much greater than 1. More basic work on complex identification has been reported by Fletcher and Flett: by Tanaka; and Jay-cock and Jones." These studies have suggested that at low loadings in the organic phase, the nickel and cobalt carboxylates appear to be dimeric and solvated by free carboxylic acid molecules. As the concentration of metal in the organic phase increases, the complex changes and larger polymeric species are formed. In order to permit assessment of the potential of carboxylic acids as extraction reagents for separation of

Jan 1, 1971

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

RACAL COMMITTEE OF ARRANGEMENTS Henry McCormick, Chairman; David Watts, Secretary; H. H. Campbell, A S. McCreath, S H. Chauvenet, C. E. Stafford, George S. Comstock, Jones Wister, E. C. Felton, F. W. Wood, Harvey Fisher. CITIZENS' RECEPTION COMMITTEE Governor H. M. Hoyt, Hon John C. Herman, Hon Simon Cameron, Hon. J. D. Cameron, W T. Hildrup, Charles L. Bailey, W. W. Jennings, Lane S. Hart, H. U. Carter, Gilliard Dock, T. T Wierman, Jr, James Boyd, D. L. Jauss, Dr. T J. Dunott, S. C. Gilbert. William J Rose, James Lynah, Dr. H. B Buehler, William N Lamberton, John Wister, G. M. McCauley, David Fleming, John Q. Donney, M. E. Olmsted, H. S Gross, Henry Gilbert. John B. McPherson, Lyman D. Gilbert, F. W. Forman, L. S. Bent, A. J. Dull, F. R. Leib, Dr. G. W. Belly, James McCormick. The opening session of the meeting was held in the hall. of the Young Men's Christian Association, on Tuesday evening, October 25th. Mr. Jones Wister, of the Local Committee of Arrangements, introduced the Hon. John C. Herman, mayor, who, in a brief address, extended to the members present a welcome to the city, of Harrisburg ; Lieutenant Governor Stone made an address of welcome on behalf of Governor Hoyt and the Commonwealth of Pennsylvania. President Metcalf responded, on behalf of the Institute, to the cordial addresses of the mayor and lieutenant-governor. The following persons proposed for members and associates of the Institute, and recommended by the Council, were unanimously elected :* MEMBERS. William F. Aldrich, - Montevallo, Shelby Co., Ala. George H Blake, - Steelton, Dauphin Co., Pa. L. Bertram Cady, - Salisbury, N. C. John B. Church, - Pottsville, Pa. Walter S. Church, - Pottsville, Pa, Frank L Clark, - Pittsburgh, Pa. * In the following list are included those elected at a subsequent session of this meeting.

Jan 1, 1882

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1' and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,'' by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.'= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists It Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I-lath St. S. W. B'ham, Ala., Phone 56-5566 MILTON H. FIES Consulting Engineer Rooms 1201-2. Albama Power Co. Bldg. Birmingham, Alabama]

Jan 1, 1952

By AIME AIME

AN unusually interesting meeting devoted to the discussion of the ways and means of improving coal mining practice, through the larger use of machinery underground, was held in the Auditorium of the Engineering Societies Building on March 11. The meeting was organized by the Materials Handling Division of the A. S. M. E. and held under the auspices of the Metropolitan Section of that Society and the National Coal Association. The New York Section of the A. I. M. E., which had been invited to participate, found itself unable to do so formally because of a conflicting date for its March meeting but informally did its part to aasure the success of the meeting. As a result of the discussion at and preceding the meeting, the National Coal Association, through Walter Barnum, chairman of its research committee, has asked the A. S. M. E. and A. I. M. E. to join the Association in a study of the present problems of the bituminous coal industry. Messrs. Harry L. Gandy, Calvin W. Rice and H. Foster Bain have been selected to act as a committee which shall develop plans for a joint program.

Jan 1, 1926

By Charles L. Thomas

A novel, highly sensitive, and reproducible nzetlzod for the determination of hydrogen in solid materials is presented. The procedure requires equilibration of the specimen with hydrogen gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subse-quent quantitative analysis by mass spectroscopy. Good linearity is obtained for the Arrl~enius plots of the investigated metals. The advantages in the use of this method over that of Sieverts aye discussed. The solubility data for copper are in reasonable agveewzent with a considerable number of other inuestigations, wllile those fov silver are considerably lower than previously reported. The first known solubility data for gold are presented. Solubility equations and heats of MUCH of the data which are available on the solubility of hydrogen in various metals and alloys have been obtained by the classical Sieverts method.' The method involves the measurement of a decrease in pressure of a gas in a calibrated system, and the calculated contraction in volume is attributed to the solubility of the gas in the metal sample. The procedure requires several corrections, such as the solubility of the gas in the container walls and the diffusion of the gas through these walls, as noted by Steacie and .Johnson2 and others. In addition, errors may be incurred due to reactions between metal surface impurities, such as oxides, and the saturating gas. The precise calibration of the measuring system where large thermal gradients exist can present additional difficulties. Also, accurate volumetric measurements of small quantities of gas are difficult. Many of the objections to the Sieverts method were overcome on solid materials by Ransley and ~eufeld,~ who first saturated the metal with hydrogen and performed a subsequent extraction and measurement of the gas by chemical means. Eichenauer and pebler4 and Eichenauer, Kiinzig, and pebler5 measured the diffusion coefficient and solubility by following the degasification of a sample as a function of a rate of increase in pressure in a previously evacuated system. Here again, however, the procedure involves many of the corrections of the Sie-verts method. The present investigation deals with the solubility of hydrogen in solid copper, silver, and gold by a technique which eliminates many of the aforementioned corrections and possible errors. This procedure requires equilibration of the specimen with gas, rapid quenching, and hot vacuum extraction of the dissolved gas with subsequent quantitative analysis by mass spectroscopy. EXPERIMENTAL Two completely separate systems were employed to accomplish first, the equilibrium saturation of the sample and second, the extraction of the dissolved gas. Saturation Apparatus. The saturation apparatus, illustrated in Fig. l, consisted of a vertically mounted quartz tube with a three-way valve for vacuum or hydrogen near the top and an outlet near the bottom leading to a butyl phthalate seal. The bottom end of the tube was terminated with a joint accommodating an O-ring sealed "Asco Stirring Gland" (The Emil Greiner Co.). This gland facilitated movement of the thermocouple without introduction of air into the system. The upper portion of the tube (above the furnace) was water-jacketed. A Welsh 1405-B mechanical pump provided the necessary system evacu-

Jan 1, 1968

R. Trimble, Pittsburg, Pa (communication to the Secretary) : There are in the proposed specifications only two points on which I wish to comment at this time.

Jan 1, 1902