Search Documents

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By R. B. Tippin, J. S. Browning

The feasibility of multistage heavy liquid cyclone beneficiation of spodumene was successfully demonstrated in this investigation. The indicated recovery for the multistage circuits was mathematically estimated as continuous test runs would be necessary to determine the true influence of a middlings recycle. In the three-stage circuit, both the concentrate analysis and spodumene recovery exceeded 90%. The two-stage circuits were unable to simultaneously yield an acceptable produce with a satisfactory recovery. With the Nation's growing industrial mineral requirements, the U.S. Bureau of Mines has undertaken the task of investigating new mineral dressing techniques and improving the existing concentrating methods of ore beneficiation. One such project is the gravity concentration of minerals using heavy liquid separation (HLS).1-3 Heavy liquid separation is based on the simple principle that a material, whose specific gravity is less than the density of a solution, will float on top of the liquid and a material with a greater specific gravity will sink. Heavy liquid separation techniques were developed in the laboratory over half a century ago but the process has yet to be commercially adopted. In the past, commercial operations have failed because of numerous problems.4 Industrial interest has recently been reactivated because of engineering advances. The number and quality of the heavy liquids suitable for mineral processing has increased while the cost has sharply dropped. New and improved liquid recovery systems5,6 are under consideration with present emphasis on 1) solvent extraction, 2) thermo-evaporation, and 3) water washing. The toxicity of the heavy liquids7 presents a problem, but throughout the chemical and mining industries, many similar hazardous materials are safely handled. A distinct advantage of using heavy liquids is its ability to provide a near perfect separation of fine-sized mineral particles even when the specific gravities are close. Effective separations have been made on minerals down to 200 mesh and with a density

Jan 1, 1968

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By Samuel S. Wyer

THE following abbreviations have been used in, the text: Cassier's, Cassier's Magazine. Eng. Lond., The Engineer (London). Eng. Mag., Engineering Magazine. Eng. and Min. Jour., Engineering and Mining Journal. Eng. News, Engineering News. Eng. Rec., Engineering Record. Engng., Engineering. Engr., The Engineer (Chicago). J. I. and S. I., Journal of the Iron and Steel Institute. Jour. F. I., Journal of the Franklin Institute. Jour. Assn. Eng. Soc., Journal of the Association of Engineering Societies. Mar. Eng., Marine Engineering. . Mem, Soc. Ing. Civ., France, Memoires de la Society des Ingenieurs Civils, France. Prac. Eng., Practical Engineer. Proc. Digs. Soc. of W. Pa., Proceedings of the Engineers' Society of Western Pennsylvania. Proc. I. C. E., Proceedings of the Institute of Civil Engineers. Proc. I. 1M. E., Proceedings Institution of Mechanical Engineers. Trans. A. I. M. E., Transactions of the American Institute Mining Engineers. Sci. Am., Scientific American. Sci. Am. Sup., Scientific American Supplement. Zcitschr. d. V. D. Ing., Zeitschrift des Vereines Dentscher Ingcnieure.

Mar 1, 1905

By R. J. McNally

THERE are three primary plant nutrients—nitrogen, phosphorus, and potassium—expressed in any fertilizer compound as percent N, percent P 2 O 5, and percent K 2 O, in that order. This article will be concerned with the first two. The chief source of P 2 O 5 is phosphate rock. As found in the western states phosphate rock is essentially tricalcium phosphate-calcium fluoride (fluor-patite). As such, it is quite water insoluble.

Jan 1, 1957

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By Louis Cates

AT THE annual meeting of the American Institute of Mining and Metallurgical Engineers in February, 1923, the Chairman of the Committee on Ground Movement and Subsidence appointed a subcommittee to work out a form of questionnaire and to collect data on subsidence and ground movement resulting from underground metal- and coal-mining operations, and on ground movement and safe slopes in connection with open-cut metal-mining operations. The author was requested to take charge of the collection of data and the preparation of a questionnaire in connection with the Committee's studies of open-cut metal-mining operations, this paper is a summary of the work carried on and information received therefrom up to February, 1924. The first approach to the problem of safe slopes is to gather all information that pertains to finished slopes; in other words, the steepest economic angle from the horizontal that will stand in order to uncover the ores to be mined and be safe while the extraction of the ore at the base of these slopes is in progress. Whether or not this angle is 35° or 45° depends on many factors. The number of benches maintained to take care of falling rock and their height and width are direct functions of this overall slope. The slope is here taken to mean the angle from the top edge of the pit through the edges of the respective lower benches to the bottom of the pit. If we accept this definition of the slope, it might save some confusion as there would be a difference if one took the line from the top edge of excavation to the toe of the bottom slope. This latter slope would not be constant, but would vary with the number of benches. The depth of the various ore faces will vary, of course, depending on the deposit; Table 1 shows this to range from 50 ft. to 1100 ft. The geology is an important factor, as are the climatic conditions under which one is operating. A saturated condition in some rock structure causes rock flows; in the Panama Canal excavation, slides have run on a ratio of as low as one on ten, which is a 10 per cent. grade, or a slope of less than 6° with the horizontal. Slopes as steep as 60° have been noted in the Utah Copper operations, so that a wide divergence will possibly be

Jan 8, 1924

By Jay A. Carpenter

This paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator: This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with a Trent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 1, 1916

By Jay Carpenter

THIS paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator. This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with aTrent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. .These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and. delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 8, 1915

By W. J. Reagan

The problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 max.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot after coming from the slicing lathe. Jusf sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By W. F. Boericke

THE character of the Wisconsin orebodies must be clearly understood to appreciate the difficulties encountered in sampling and estimating them. Unlike the western vein deposits, they do not lie between regular walls, but form large, often highly irregular bodies, on a single floor in the so-called Galena limestone. The bottom of the ore is nearly always on the clay bed, a flat generally well-defined clay seam a few inches thick, which marks the junction of the base of the Galena lime and the top of the next formation, the Trenton lime. Above the clay bed, the orebodies make the unique pitch and flat formation described by Chamberlin.1 Theoretically, we should find two pitches, one on either side of the top crevice, diverging as they go down, with the final flats a considerable distance apart on the clay bed. The area between, known locally as core ground, should thus constitute a single defined orebody, with the richer portions near the pitches and the leaner portion in the center of the core. Practically, we find few examples of this perfect orebody. Almost invariably one pitch is better defined than the other, and often the opposite pitch is marked only by a faint line of fracture showing stronger mineralization than the wall rock, or it may be totally lacking. But with an orebody of any size or richness, at least one strong pitch usually tends to follow an east-west trend, or a quartering course. Late mining developments in the rich New Diggings field indicate that these pitches often assume a horseshoe or crescent shape, the richer ore being in the heart of the crescent and the pitches showing less mineralization as they extend outwards. In the northern end of the field, on the contrary, the pitches maintain generally a consistent direction, and have been mined for thousands of feet from the shaft. The length of the orebody may be several thousand feet, the height varying from 10 to 60 ft. and the width from 60 to 250 ft. In fact, on the core side, there is no definite end to the ore. The mineralization simply gets thinner and thinner, and the limit of working depends on the cost sheet and the profit from the recovery.

Jan 2, 1922

By AIME AIME

MINERAL production of the United States is valued at over five billion dollars a year at present and the industry employs close to a million workmen, yet such maps as are available that might indicate the geographical distribution of this industry show only the location of coal and oil fields and of other mineral deposits. No recent map is available that shows this distribution in a quantitative way. The purpose of the maps and graphs here presented is twofold: (1) to give the mining engineer a clear conception of the relative value and the pattern of distribution of minerals in the United States; (2) to test the so-called block-pile (or grouped pillar) system of statistical mapping, which makes this presentation possible. (I discussed this method of mapping in an article which appeared in Economic Geology in 1939, Vol. 15, p. 185-188.)

Jan 1, 1941

By Elmars Ence, Harold Margolin

The Ti-Fe and Ti-Fe-0 systems were re-examined because of the controversy regarding the existence of Ti2Fe, and to consider all available data points to the existence of Ti,Fe. The Ti-Fe-0 system contains two ternary compounds: E, corresponding to Ti2Fe; and y. SEVERAL authors have investigated the constitution of titanium-rich alloys of the Ti-Fe system. The most extensive study of titanium-rich portions of the Ti-Fe system was by Van Thyne, Kessler, and Hansen,' who investigated this system up to 50 pet Fe and used the highest purity materials available for their alloy preparation (iodide titanium was used for alloys up to 20 pet Fe). According to Van Thyne et al., phase relationships in the region of investigation are governed by phases a,ß, and TiFe. No evidence of an intermetallic compound Ti,Fe was found. although earlier. works by Laves and Wallbaum,' and Duwez and Taylor' reported its existence. Rostoker's study on the occurrence of TilX phases" confirmed the findings of Van Thyne et al. Rostoker proposed that the compound Ti Fe found by Duwez does not exist but is actually a ternary compound, Ti1Fe3O, originated by inadvertent oxygen contamination. The partial isothermal section of the ternary Ti-Fe-0 system as reported by Rostoker' seems to confirm this explanation. In the course of phase diagram work conducted at New York University, however, certain irregularities were observed to be associated with ternary systems of the type Ti-Fe-X. The ternary phase 6, observed in the systems Ti-Fe-Mo' and Ti-Fe-V." was found to be structurally identical to the com-pound Ti2Fe as reported by Duwez and Taylor, and to Rostoker's compound Ti1,Fe2O. Since the amount of oxygen possibly present in the Ti-Fe-Mo and Ti-Fe-V systems could not account for the observed amounts of the compound, it appears that the d phase in these systems is not Ti,Fe,O. On the other hand, considering the amounts of the 6 phase, particularly in the Ti-Fe-Mo system, the location of the phase was uncertain. It was felt that the introduction of the Ti2Fe phase would alleviate some of the inconsistencies of the two systems. Because of the uncertainties relating to the phase Ti2Fe, or Ti1Fe2O, it appeared worthwhile to re-examine the Ti-Fe and Ti-Fe-O systems in the vicinity of these compounds with highly sensitive metallographic techniques and with X-ray methods. Experimental Procedure Alloy Preparation—For the study of the binary system four alloys were prepared, containing 26.9 (30 wt pct), 34.0 (37.5 wt pet), 41.2 (45 wt pet), and 56.3 (60 wt pet) atomic pet Fe, and for the ternary Ti-Fe-O system 18 alloys were prepared in the composition range of 1.6 to 16.9 atomic pet 0 and 24.3 to 55.7 atomic pet Fe. The materials used for the Ti-Fe alloys were iodide titanium (99.98 pet Ti, 0.002 pet 0) and Ferro-vac-E iron (99.95 pet Fe, 0.0052 to 0.0072 pet 0). For the Ti-Fe-O study the materials used were sponge titanium containing less than 0.06 pet 0, Ferrovnc-E iron, and Baker's analyzed TiO2. The nominal weight and atomic percentages of the ternary alloys prepared are shown in Table I. Melting—Charges of 10 to 15 g were melted in a nonconsumable arc furnace in argon atmosphere according to the technique described elsewhere.'" Since there was practically no weight loss through the various stages of melting and oxygen losses have not been observed previously, it appeared justifiable to use nominal composition for interpretation of data. Iodide titanium control buttons, of the same mass as the Ti-Fe charges, and melted under the same conditions, were used to check hardness pickup during melting. A hardness increase of 2 to 3 Vhn was found. Heat Treatment—The specimens were annealed in quartz capsules under argon. To avoid contact between the specimen and capsule material all specimens were wrapped in titanium sheet. The annealing times are given in Table 11. The attain-

Jan 1, 1957