Search Documents

The need to hoist increasing loads from great depths is leading to the more general adoption of winders of the Koepe and Blair types. The trend has introduced a number of new problems in winding ropes, more particularly in the Koepe system where regular destructive tests during the life of a rope are not possible. Consequently, the importance of introducing non-destructive tests is much greater, especially so in the case of Koepe ropes used for deep winding where there are three major destructive fatiguing influences. These are rotational effects when a vertical rope is changed end-for- end each trip, the much greater range of stress to which the rope is subjected each trip as compared with drum winding, and the destructive effect of a high coefficient of friction between wheel and rope. A plea for a lower coefficient in the interest of better rope and tread life, substantiated by analysis, is made for Koepe winders operating at depth.Co-ordination of rope testing with general hoisting problems is stressed and the active participation of the Wire Rope Committee of the Australian Mineral Industries Research Association Ltd. in the promotion ofthe project is noted.The general introduction of a rope testing programme in Australia, personnel requirements and some local basic research in the subject to cope with future demands are considered.

Jan 1, 1967

By Richard Frentress, Dave Donelon, Robert Henderson, Mike Warnert

"The Round Mountain gold mine is an open-pit mining operation located 97 kilometres north of Tonopah in Nye County, Nevada. Gold has been produced from the property since 1906.Gold is currently recovered using a combination of four independent processing operations. These include a 10,000 ton per day mill, a 30,000 ton per day, crushed ore heap leach, a 150,000 ton per day, run-of-mine ore heap leach and a small high-grade gravity concentration circuit. In 2002, Round Mountain Gold Corporation produced 755,494 troy ounces of gold at a total direct operating cost of US$2.14 per ton ($193/oz).This paper presents a summary of the Round Mountain operations and discusses some of the processing innovations that have enabled the mine to profitably recover gold from a large low-grade ore body.INTRODUCTIONRound Mountain Gold Corporation is a 50/50 joint venture between Kinross Gold Corporation and Barrick Gold Corporation. Kinross acquired its ownership interest in the Round Mountain mine upon completion of combination with Echo Bay on January 31, 2003. The joint venture partners continue to support an aggressive exploration program in the vicinity of the mine in order to add reserves and extend the mine life.The Round Mountain mine currently operates a conventional open pit that is approximately 8,200 feet long, 4,900 feet wide and 980 feet deep. Mining is conducted on 34-metre benches by electric shovels and front-end loaders paired with 150, 190 and 240-ton haul trucks. Blasthole samples are collected and assayed and provide the control for ore segregation. Based upon these assays, blasted pit rock is determined to be run-of-mine Dedicated Pad ore, crushed Reusable Pad ore, high-grade ore or waste.Gold is recovered using a combination of four independent processing operations. These include run-of-mine ore heap leaching (Dedicated Pad), crushed ore heap leaching (Reusable Pad), milling and the gravity concentration circuit. Non-mineralised rock is delivered directly to the waste dumps. Low-grade ore is trucked directly to the Dedicated Pad and medium-grade ore is crushed and placed on the Reusable Pad. High-grade ore is handled in one of three ways: 1) leached on the Reusable Pad and offloaded to the mill; 2) sent directly to the gravity plant with tails reporting to the mill; or 3) sent directly to the mill or mill stockpile. The gold particle size distribution of highgrade ore determines the processing method."

Jan 1, 2005

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By M. Sagheer

An 8.5-km (5-mile) conveyor has gone into operation in western Turkey to eco¬nomically transport crushed lignite from the mine area to a power plant. This conveyor has replaced trucks as the principal mode of transporting the lignite. One principal element of Turkish govern¬ment policy is the country's commitment to increase electricity supplies for mining and other industries. Lignite is an important source of electric power supply in Turkey. Production was about 48 Mt (53 million st) in 1987, amounting to more than 20% of the total power supply in Turkey. In the western Anatolia supply network, it plays a major role for power generation. Deposits are located in the Soma region of western Turkey. The lignite is of low quality, deposits are scattered, and the terrain is dif¬ficult and hilly. These conditions demand an economical and technically feasible method of transporting the raw material from mining areas to the central thermal power plant. The Soma power plant is located about 120 km (75 miles) northeast of Izmir, near the coast of Aegean Sea. An overland conveyor of a unique design has gone into commercial operation at the Soma power plant facilities of the Turkish state electricity organization, Türkiye El¬ektrik Kurumu (TEK). The conveyor re¬places truck transport to ensure economical use of the lignite deposits. Computer-aided design (CAD) added more precision, qual¬ity, and flexibility of engineering in design activities. It also helped quick realization of the project that was executed in cooperation with the German company Krupp Industri¬etechnik and the Turkish firm Gama Endüstri AS. Unique features The conveyor includes several major features rarely combined in a single flight: Overland long distance conveyor. • Horizontal curves. -Steep vertical concave and convex curves to match the difficult terrain. Down-hill conveying. Frequency converter drives with vari¬ able belt speed. Generating operation mode to backfeed the energy to the network. Layout The 8.5 km (5 mile) long conveyor takes the -200 mm (-8 in.) lignite from the primary crushing plant located near the mine to the central, final crushing plant located in the stockyard area near the power station. The drive and belt tensioning assemblies are situated near the tail end of the flight. The high voltage switchgear is housed in a room in the primary crushing plant build¬ing upstream from the conveyor flight. The frequency converters are installed in the low voltage switchgear room located below the control room within the primary crushing plant building. Conveyor design The conveyor includes two 4 km (13,120 ft) radius horizontal curves, one left-hand and the other right-hand. The minimum radii

Jan 1, 1989

By Patrícia Freitas Rodrigues

Um comparativo entre dois métodos para determinação das temperaturas de transformação de fase, tendo como base análises de Calorimetria Diferencial de Varredura (DSC) em amostras de uma liga de NiTi equiatômica submetida a tratamentos térmicos para envelhecimento, foram utilizados neste trabalho. Sendo aplicado o método clássico comumente utilizado para análise desses resultados e o método utilizando da integral do pico de transformação de fase. Com base nas avaliações feitas, o método de integral por apresentar uma relação direta da fração de transformação demonstra-se mais eficaz para determinar o início e o fim da transformação por levar em consideração a forma do pico em função da trajetória de transformação.

Aug 8, 2018

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By Grainne A. Matthews

Jan 1, 2009

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

This paper deals with the application of table flotation to two unusual mineral dressing problems. Both problems involved the removal of interfering minerals at sizes too coarse to normal froth flotation.The first problem was the removal of arsenical minerals from Broken Hill gravity concentrates without further size reduction. Table flotation without grinding of the original concentrates gave almost complete rejection of the arsenic from the concentrates. A typical test result was a reduction of arsenic in jig concentrate from 0.75% arsenic to 0.007% arsenic.The second problem was to develop a method to produce a high grade calcium carbonate concentrate from coastal dune sands containing about 10% silica and about 80% calcium carbonate. The sands were about 30 mesh British Standard Screen (B.S.S.), and for economic and other reasons it was stipulated that the separation be made without grinding. Again, table flotation gave excellent results. A concentrate was produced containing 99.62% acid soluble material, representing a recovery of 98.69% of the calcium carbonate in the feed with a rejection of 96.44% of the silica.The investigations' were carried out at the Kalgoorlie Metallurgical Laboratory, under the Department of Mines...

Jan 1, 1954

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By J. Hurdley, J. A. Plant, H. Robotham, P. R. Simpson, G. C. Lalor

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results of orientation studies for a regional geochemical survey of Jamaica and the CARICOM countries of the Caribbean region are described. The survey is designed to provide systematic geochemical information for a wide variety of applications and, especially, to form a basis for agricultural development in the region

Jul 1, 1991

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By A. Ploszajski

This item examines the history and uses of tungsten, from discovery to superalloys via the lightbulb and electron beam instruments.

Apr 1, 2015

Japan is the largest coal importer in the world, importing from Australia, China, Indonesia, Canada, Vietnam, etc. In Indonesia, most of the produced coal is extracted from open cut mines. More open cut coal mines will be developed to fill the demand for coal in Indonesia and the world. Many surveys and projects for developing new coal mines and transferring mining technology are being conducted in tropical counties such as Indonesia and Vietnam with the aid of the Japanese Government. It has, however, been pointed out that excessive and precarious development of mines in tropical areas will damage the environments around the mines including cultivated lands, and reduce the precious rainforest. This would undoubtedly exacerbate the instability of the global climate and the food crisis in the world. This paper describes the effects of flyash on the control of acid mine drainage in order to avoid potential negative impacts on the environment caused from open cut coal mines.

Dec 6, 2010

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By D. E. Ng?andu

The experience of Mufulira concentrator, of the Zambia Consolidated Copper Mines Limited, with underground mine drainage water, which is used in milling operations is discussed. It is shown that the underground mine water has a deleterious effect on flotation performance. The adverse effect of the underground water was successfully negated by adding lime into the primary ball mills and increasing the pH of the slurry, from a ?natural? pH of 8 to the flotation pH of 10.5. Traditionally, the pH modifier, quicklime, had been added downstream of the milling. Changing the lime addition point further reduced lime consumption by 50%,?a key issue as lime accounted for over 60% of the Mufulira flotation reagent costs. The nature of the effect of the underground water at Mufulira, particularly the sensitivity of the flotation to the pH at which the milling was conducted, characterized galvanic interaction. A large-scale plant situation is presented in which the desired electro-chemical response in the flotation was achieved, by a deliberate manipulation of the milling environment. The experience provides practical testimony of a more fundamental role for the milling process, other than the mere physical preparation, i.e. size reduction and liberation, of mineral particles prior to flotation.

Jan 1, 2001