Search Documents

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

1. Domestic Production and Use: In 1980, 13 companies operated 33 primary aluminum reduction plants, with 3 firms accounting for 62% of production. Washington, Oregon, and Montana accounted for 30% of the total production; Texas, Louisiana, and Arkansas 19%; Tennessee, Alabama, and North Carolina 15%; other central and eastern States 36%. Based on published producer prices output of primary metal in 1980 was valued at over $7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 26% of domestic consumption in 1980, building 22%, transportation 21%, electrical 12%, consumer durables 7%, and other uses 12%.

Jan 1, 1981

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By Mark R. Svinkin

This paper deals with application of the wave equation analysis to determine capacities of piles driven in saturated sandy soils. It shows that pile capacity in sandy soils changes with time after the completion of pile driving and depends on the ground water elevation. In saturated sandy soils the setup coefficient ranges between upper and lower curves represented by power functions. For a reliable prediction of pile capacity wave equation input should be adjusted with soil damping. Back calculation of soil damping from known pile capacity performed for five tested piles shows that skin damping coefficient changes with time in the same manner as the pile capacity and can be represented by the power functions for considered damping models.

Jan 1, 1995

By M Boyd

The University of Wollongong was named University of the Year 2000, for its work in preparing students for the e-world. Computer facilitated learning is being introduced into subjects throughout the engineering course. First year mining engineering students are introduced to computers, e-communication, using the UniversityÆs web based information system, and web based subject delivery. Mining engineering students in the mid-years of the course use programming languages and numerical computation software such as MATLAB, while students in the final years use a range of commercially available professional engineering software such as TALPAC. Most of these subjects are offered as part of the UniversityÆs Learning Online program, co-ordinated by its Centre for Educational Development and Interactive Resources (CEDIR). Learning Online subjects are delivered using the Web Course Tools (WebCT) environment. WebCT allows all resources to be accessed through the web, allows email communication between lecturer and student, and allows discussion groups for the exchange of ideas. Students can submit their assignments through WebCT and receive immediate feedback. This paper describes how WebCT has been used to deliver a first year engineering computing subject, mid-year numerical computation subjects, a mining economics subject and mine planning subjects.

Jan 1, 2002

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1996

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

When we are beset with the economic problems the world faces today, we are always inclined to look at the shorter term future. Today I would like to take a long-term view of our industry, project historical demands for our products into the future and discuss opportunities for our members. Perhaps we could firstly look at the long-term demand trends for our metals. If I tend to use non ferrous metals as a basis for my figures it is because this data is more readily available to me. I am sure that most other products of our industry show similar trends.

Jan 1, 1992

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963