Search Documents

By S C. Dominy

This contribution examines the effect of feedstock sampling before the sorting stage of polyethylene terephtalate (PET) bottle recycling. Batches of waste PET bottles may contain non-PET bottles which need to be removed by sorting. Any residual presence of PVC is detrimental for the quality of products manufactured from recycled PET. The maximum tolerated concentration of PVC in cleaned PET is extremely low, which places high demands on the recovery of PVC achieved by sorting. To be confident of attaining the desired PET quality after sorting, acceptance sampling of truckloads of PET bottles may take place prior to sorting. It is shown that accounting for sampling uncertainty requires that the sorting process achieves a consistently high recovery of PVC bottles.CITATION:Glass, H J and Dominy, S C, 2017. Plastics recycling and sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

The Coeur Rochester Mine is one of the largest and lowest cost primary silver mines in the United States. In January, the mine surpassed 3.1 kt (100 million oz) of historic silver production. Rochester is owned and operated by Coeur d’Alene Mines, the world’s largest primary silver producer. Rochester is the world’s seventh largest silver mine. It also produces gold — more than 31.1 t (1 million oz) in historic production. Cash operating costs have averaged 8 cents/g ($2.58/oz) of silver since operations began in 1986.

Jan 1, 2004

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By Edward Hall Smith

The E1 Indio Mine is located in the Andes mountains about 180 kilometers East of La Serena, capital of the Fourth Region of Chile. It is reached by an international highway running up the Elqui Valley as far as Juntas from where the last 42 kilometers is on a road constructed by the Company. The plant is located at 3.900 meters above sea level among extremely rugged terrain with nearby mountains rising about 5.500 meters. Climatic conditions at these altitudes are severe with winter temperatures down to -20°C. Snow storms lasting several days and leaving up to two meters of snow have been experienced, while fierce winds are corm=.

Jan 1, 1984

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By Ike Isagon

Outline 1.Background Sudbury Backfill Operations 2.Alternative Binder 3.Alternative Binder Trial Process Flow Diagram ?Laboratory Results ?Plant Trial ?Final Evaluation and Approval ?Management of Change (MOC) 4.Economics 5.Conclusion 6.References and Acknowledgements

Nov 1, 2011

By T S. Giraudo

The Macraes Gold Project, operated by GRD Macraes Limited, engaged GRD Minproc Limited to assist with the evaluation of a pressure oxidation circuit, this being the key component of a recovery enhancement project. The initial study gave sufficient confidence in the process to enter into project execution. GRD Macraes Limited was the first company to license Newmont Mining Corporation's pressure oxidation technology, which aims to improve gold recovery from the carbonaceous sulfidic flotation concentrate. This paper outlines the fundamental chemistry of the process followed by a description of the plant that was ultimately installed. A summary of the commissioning is given together with an overview of the production results to date. The project ramp-up was rapid, with design temperature and throughput being achieved within days of hot commissioning. Gold recoveries have exceeded expectations, improving from around 70% prior to the installation of pressure oxidation to above 84%. The project has increased the nominal gold output at Macraes from 120,000 oz/y to 170,000 oz/y. On-going plant optimisation for process parameters is discussed, giving rise to flexibility in gold production, with key controlling parameters exceeding design.

Jan 1, 2000

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003

By B. S. Van Gosen

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Jan 1, 2009

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By E. L. Garton

[The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying; southwest of the Arbuckle Mountains. It includes six counties: Carter, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvania age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/ being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.]

Jan 1, 1941

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P E. H Gregg, D Horne, R B. Stewart, N Bolan

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100 000 mm of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity inNew Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.   The suitability of the tailings as a potential plant growth medium was assessed with the end view of revegetating the tailings dam and alleviating AMD. This paper outlines characterisation work conducted on the tailings and summarises preliminary results from plant growth trials. The tailings contain up to 5% Fe, 1.15 % Pb, and 0.45% Cu in the form of sulphide minerals. The distribution of heavy metals, sulphate and total sulphur with depth indicates that the top 200 - 300 mm of the tailings have been extensively weathered since their deposition. The oxidation of sulphide minerals, particularly pyrite (FeS2 ) has reduced the pH of the tailings to nearly 2 in places. Below 300 mm the sulphide minerals are largely unweathered and the theoretical acid generating potential of the tailings exceeds 170 Mg CaCO3/1000 Mg tailings at certain depths. Plant growth trials were conducted to study the effects of lime and organic matter addition on the establishment of vegetation on the Tui mine tailings. Several plant species were assessed including some cultivars bred for their tolerance of heavy metals.

Jan 1, 1995

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By L. Rademeyer, P. Mazzoni, C. Kubank, F. Brown

The Corridor Sands deposits of heavy mineral sands represent the largest known economic resource of titanium dioxide minerals. The West Block of Deposit 1 alone contains Measured and Indicated Mineral Resources of 1.7 billion tonnes containing 4.14 per cent ilmenite, estimated in accordance with the JORC standard, sufficient for at least the first 20 years of mining. Total mineral resources are estimated to be approximately 17 billion tonnes at 5 per cent Total Heavy Minerals (THM). Test work was undertaken on the West Block of Deposit 1 over a period of two years in order to develop the process flow sheet to bankable standards. Geological, mineralogical and metallurgical test work was integrated from a pre-feasibility stage to the full bankable stage. The process flowsheet was developed with the central objective of the production of saleable products, of consistent quality and acceptable to the respective end-markets. The aim of this paper is to describe the way in which the various challenges for the project have been addressed by using integrated geological and mineralogical information, which has resulted in the development of a complete flow sheet. The process confirmed that material within customer specifications could be produced, once various metallurgical parameters were understood. This flow sheet development progressed from laboratory test work through to full field trials at pilot plant scale on large consignments of mineralized material. The flow sheet was developed to such a standard as to be used with confidence for both engineering design and cost estimates, and to determine the recovery factors to be used in financial evaluations. Keywords: Corridor sands, Flow sheet, Pilot plant Titanium dioxide

Jan 1, 2003

By J. G. Henning

Following completion of planned mining operations at the Goldcorp Dome Open Pit Mine, a high-grade Shaft Pillar located in the pit highwall was recovered. Mining of this Shaft pillar faced numerous rock engineering design and implementation challenges due to its remote position on the highwall and the presence of mine workings within the wall. The case example presented in this paper discusses the geotechnical investigation performed at the site, novel measures undertaken for installation of ground support required for rockmass reinforcement and for worker protection, as well as operational challenges to successful mining of the Shaft Pillar.

May 1, 2009