Search Documents

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Joachim Klein, Frank Reimann

Nodular-graphite cast iron (GGG) is a material similar to steel, and one which exhibits excellent properties, in particular for components exposed to pressure. GGG cast iron has been used in many cases when sinking mine shafts with conventional tubbing. With linings made of cast iron tubbings (the backfill concrete is not integrated into the calculations, and merely serves as bedding) the properties of the cast iron can be made full use of, provided the tubbing is made to the appropriate cross-section. Calculations have shown that better static values can be arrived at when using cross-sections other than those of tubbings made to conventional German standard. The cross-sectional design of the new types of shaft lining made from GGG is to be developed on these lines irrespective of the cast iron structure being only stressed component or its restistance function being combined with the one of concrete. GGG 50 is used for the first time to make the reinforcing inner liner of a main shaft currently sunk in Germany. The physical properties of nodular-graphite cast iron, strength and deformability, suggest that, in the future, its application will not be restricted to shaft support but also in tunneling. New moulding techniques with better three-dimensional modelling resulted in new tubbing designs as installed e.g. for the Hannover underground at present. Shield-driven tunnels have to withstand earth and water pressure, apart from axial machine loads. In this field time is money as well. Therefore easy handling and quick installation are necessary for successful, use. Last but not least, safety is of first-order importance for work in shaft sinking and tunneling. Cast iron lining systems, accordingly, are adequate systems, in particular for excavations underneath water for transport systems and for goods and passengers.

Jan 1, 1987

By M. Heger

February 2, 1999 marks a milestone in earth-moving technology at the San Miguel Lignite Mine. It was on that date that The North American Coal Corporation (NAC) took delivery of three Leica Dozer 2000 GPS grade control systems for use on its bulldozers. The primary reason for the purchase of these grade control systems was to prove that GPS technology could safely and economically be utilized on heavy equipment to assist operators in defining grades. If these properties were successfully demonstrated, the ultimate vision of the project was to expand the system to a point were GPS would become the primary means of providing grade control information to the mine’s heavy equipment operators. Twenty nine months and more than $500,000 later this vision was realized when the final bulldozer operating at the San Miguel Lignite Mine was equipped with Dozer 2000. Presently North American Coal has a total of nine Dozer 2000 GPS grade control systems at San Miguel providing cut and fill information to operators 24 hours a day. These grade control systems have allowed the San Miguel operation to increase safety, reduce costs, improve operator attitude, and better ensure environmental compliance. This article discusses both the nature of these benefits and some of the issues that had to be dealt with along the way.

Jan 1, 2002

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Z. H. Zhou

It is difficult to remove cadmium from raw indium using only electrolytic refining because their standard potentials are similar. In this paper, physical and chemical methods were used to remove Cd from raw indium. Indium metal is vacuum refined for two hours at 400°C with a vacuum pressure of 20 Pa. In this process, 99.70% of the Cd can be removed. The removal rate of Cd reaches 90% to 95% when indium is further smelted for 10 minutes in a 20% glycerin solution of KI and I2 at 180°C. When pre-indium is electrolytic refined in an In2(SO4)3-H2SO4 system, in which the indium content is 80 to 100 g/L, the pH is 2.0-3.0 and the current density is 80 to 100 A/m2, the contents of the impurities decrease and the purity of the indium product reaches 99.99%.

Jan 1, 2007

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

Perception has the unfortunate habit of becoming reality. Urban inhabitants unfortunately do not regard mining as a legitimate or desirable business, despite its contribution to Australia's export income (+A $8,000 million, being nearly a third of all exports); share of GDP (it is 4.5%); and the fact that its presence fills up all the empty spaces northwest of the Adelaide-Melbourne-Sydney-Brisbane crescent of inhabitation. The huge economic contribution of Australia's minerals industry, resulting from providing more than half of merchandise exports (Figure 1), is achieved by employing only some 2% of the national work force (Gaulton, 1997). Unfortunately, the minerals industry's critics generally oppose exploration on the basis that what you don't know will not hurt you. It is the 'do-not-confuse-me-with-facts' philosophy or 'ostrich syndrome', which somehow crudely assumes that mining practices have stayed in the style popular circa late 1800s. Somehow ignorance really is bliss for these idealistic believers, who are reminiscent of the members of the Flat Earth Society!

Jan 1, 1997

By S. P. Lewis, R. L. Sundeen

Most of us are aware of the ever increasing use of underground space. At the Advisory Conference on tunneling in Washington, D. C. in June of 1970, the demand for construction oriented tunneling during the 1970s was estimated at some 21,000 Km of length with an excavation volume of 675 million cubic meters. Of this total, 11 million cubic meters were forecast for underground parking. Though this is a small portion of the total, it is significant to note it represents a 280% increase over the previous decade. Other areas of unusual increase were railroad tunnels, 150%, and rapid transit tunnels, 160% (1). Faced with this increasing demand, the need for improved excavating efficiency is obvious. Great strides have been made. In Japan, for example, several new long tunnels have been driven parallel to old existing ones at costs as much as 50; under those of the original tunnels (1). This is an impressive achievement. I am certain, however, that we would all agree that even greater improvement is required. Great emphasis is being placed upon sophisticated systems which include among others, mechanical borers, thermal fracturing, and various methods of rock weakening and softening. However, in hard rock excavation the fact remains that the drill-blast method continues to be the most widely used system. Undoubtedly it will continue to be one of the most important techniques in the forseeable future.

Jan 1, 1974

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By M. K. G. Vermaak

Spiral concentration forms a crucial part of gravity separation circuits. The application of process models in the operation of gravity separation circuits offers significant benefits in recoveries and grade control. Significant strides in the modelling of spiral concentrators have been made during the last couple of decades. Despite these advances in modelling techniques and models, application in industrial processes is not fully optimized. The adjustment of splitter positions to accommodate changes in the feed parameters is impractical and difficult, resulting in losses. In this work an optical method is employed to detect the concentrate band position as a function of operating variables. As expected, the results indicate a strong influence of the solids content and total heavy mineral (THM) feed grade on the predicted gangue-mineral interface. Viscosity modifiers indicated the band position to be sensitive to viscosity and therefore the slimes content. Validation on an industrial sample indicated the possibility of using this model in feed-forward control application.

Jan 1, 2008

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By T Wambeke, J Benndorf

A risk-robust development of a heavy mineral resource requires an assessment of the geological uncertainty and spatial variability of the key factors impacting the mining and processing operation. Attributes of interest are the total heavy mineral grade, the slime content and the amount of oversized particles. The modelling of a mineral sand deposit presents two main challenges. Firstly, the exact location of the geological boundaries are obscure due to the complex interaction of the deposit formation processes. Secondly, the properties of interest exhibit a rather complex transitional behaviour across the so-called soft boundaries. Traditionally, the modelling exercise is restricted to a consecutive stochastic simulation of distinct geological facies and orebody properties. This results in different zones separated by hard boundaries, ignoring the typical transitional behaviour.This contribution presents an alternative approach which models the entire sand body as a single domain while accounting for the complex trends present. Error curves are used to infer covariance model parameters without the need of a prior removal of the trend. The principle is based on minimising the differences between empirical and theoretical errors resulting from two methods of prediction calculated for different rings of influence. The added value results from the unambiguous decomposition of the spatial variation into a deterministic trend and a stochastic residual. The trend model neither overfits nor underfits the data. The calculated residuals are thus unbiased and the uncertainty can be correctly assessed.The effort results in a characterisation of the resource uncertainty which provides a more realistic image of the spatial variability of the key properties in and across the geological domains of an existing heavy mineral sand deposit.CITATION:Wambeke, T and Benndorf, J, 2014. Optimal inference of modelling parameters to simulate complex trends across soft boundaries – a case study in heavy mineral sands, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 73–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014