Search Documents

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices which minimize soil compaction will produce better results when forestland is the intended post-mining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees, and since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal, and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree survival rate. It is believed that the two soil compaction parameters may ultimately be used to predict tree survival rates on reclaimed surface mined lands.

Jan 1, 2001

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By F F. Pitard

The comparison between J Visman and C O Ingamells’ works with P M Gy’s works has been the object of intense debates in the past. Such negative debates inevitably resulted in a loss of many good opportunities. The author’s long experience in applying works of these three authors led to the pragmatic conclusion that it is relatively easy to integrate everything Visman and Ingamells created into the Theory of Sampling; therefore, it is suggested that the compatibility has been vastly overlooked, and a correction for such anomaly is recommended. It is important to emphasise that Visman and Ingamells works may be beneficial and provide relevant, harmonious additions in some areas, and ultimately offer attractive possibilities to sampling practitioners. Such additions may enhance our capabilities to predict sampling difficulties by using a stronger strategy and to design better sampling experiments that would allow us to further understand the heterogeneity of minor constituents, and especially trace constituents. Basically, the suggested integration is essential for sampling trace constituents in the environment, in food, in chemicals and in the pharmaceutical industries.CITATION:Pitard, F F, 2017. Integration of Visman and Ingamells’ works into the Theory of Sampling – a necessity to expand possibilities in sampling practices, in Proceedings Eighth World Conference on Sampling and Blending , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By F. Russo-Bello

TauTona Mine (the renamed Western Deep Levels East) is using a longwall mining method with stability pillars to extract the Carbon Leader Reef at a depth ranging from 2097 metres to 3456 metres below surface. Seismic activity and the complexity and hazards associated with negotiating geological features at great depth pose the most severe hazard to deep level gold mining in South Africa. It impacts negatively on safety and the profitability of the mining. The critical success factors in longwalling at depth are: ?Sound mining strategies and face shape control ?Ensuring follow behind development infrastructure is kept up to date ?Support system design as a strategy to effectively limit the serious effects of damaging seismicity. This paper describes the following: ?Implementation of the required mining strategies ?The evolution of a new stope support system and problems associated with its development and implementation. How this support system was adapted for the successful negotiation of major geological features with known seismic potential and problems encountered ?Current initiatives to optimize follow behind development infrastructure ?Current initiatives in designing a new gully support system and problems experienced with its development and implementation. Finally, this paper will deal with the way forward, briefly covering areas like the above-mentioned gully support system, the proposed phased introduction of technology, and the use of alternative mining layouts.

Jan 1, 2000

By J. A. Ober

"In 2015, the estimated value of nonfuel mineral production in the United States decreased by 3 percent from that in 2014 (Table 1), mainly as a result of decreased metal and metallic mineral prices, especially iron ore, copper and precious metals. Lower metal prices were attributed to decreased consumption, especially in China and increased global inventories. Several U.S. metal mines were idled in 2015, including the only U.S. rare earths mine at Mountain Pass, CA. Downstream processors also were affected, with smelters and refiners either shutting down or idling production lines. Increases, however, took place in the value and quantity of production of industrial minerals, especially those used in the construction sector, including cement, construction sand and gravel and crushed stone. Trends in mineral-related sectors of the domestic economy, except for iron and steel manufacturing, aluminum manufacturing, coal mining and metals mining, all experienced growth (Table 2).Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct comparisons based on weight meaningless (Fig. 1).Mineral industry performanceThe estimated value of domestic nonfuel mineral production, including metals ($26.6 billion) and industrial minerals ($51.7 billion), in 2015 declined to a total of $78.3 billion, from $80.8 billion in 2014 (Table 1). However, as shown in Fig. 2, minerals remained fundamental to the United States economy, contributing to the real gross domestic product at several levels, including mining, processing and manufacturing finished products. Net exports of mineral raw materials and old scrap were $14.4 billion. Domestic raw materials, along with domestically recycled materials, were used to produce mineral materials worth $630 billion. These mineral materials, including aluminum, brick, copper, fertilizers and steel, and net imports of processed materials (worth about $32 billion) were, in turn, consumed by downstream industries with a value added to the gross domestic product estimated to be $2,490 billion."

May 1, 2016

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By C E. J de Ronde, J L. Mauk

Sulfide chimney samples collected during the 1998 - 1999 R/V Atlantis û DSV Alvin 3 - 30 research cruise have been examined and classified into four types, based on common characteristics. Chimney morphology is the most important characteristic and resulted in the following groups: 1. flutes, 2. cones, 3. wide-flats, and 4. beehives. Other characteristics resulted in the classification of subgroups within the flute, cone and wide-flat groups. The combination of characteristics, including; the presence of an orifice, internal chimney fabrics, wall thickness, extent of weathering, and the presence of Alvinella worm casts, enable evolutionary trends between the different chimneys types to be established. These trends indicate that with time, flutes evolve from immature zoned chimneys with a central orifice and smooth thin-walls, into cone chimneys with thick walls and massive fabrics which have their orifices infilled by massive sulfides, and a rough exterior. Repeated mineralisation within, cones may result in the formation of wide-flat chimneys. Beehive chimneys can form at any time during chimney growth.

Jan 1, 2003

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By S. M. M. Safvi, A. Jowett

Small-scale continuous flotation tests are described in which the influence of 1) pulp density and 2) feed rate on the rate of flotation are investigated. The results provide further evidence of first-order kinetics for flotation and indicate that tests at different feed rates provide a particularly simple method of determining rate constants. Flotation kinetics are discussed in general terms. Over a period of many years numerous research workers have studied the rate of recovery of valuable materials from flotation pulps with a view to deter-mining the mechanism of the froth flotation process. Froth flo ation is fundamentally a collision process involviug at some stage collision and then mutual attachment between air bubbles and mineral particles. It is possible to draw analogies therefore between the flotation process involving mainly macroscopic particles and the ordinary processes of chemical reaction kinetics involving collisions between atoms, molecules and ions. By adopting this analogy we may postulate a general equation representing the kinetics of the flotation process: -dC/dt =K.CC ,Aa (1) The rate constant, K, will be a complex function involving reagent concentrations, particle and bubble sizes, induction times and no doubt flotation cell design. However, these are factors which can be kept constant in any series of experiments, permitting investigation of the exponents a and c, which determine the order of the reaction occurring in flotation. The various research investigations carried out so far have all aimed at evaluating a and c and in the majority of cases only since the concentration of air has usually been kept constant in a series of tests, so that a relationship of the following type has been investigated: -dC/dt = K1 Cc (2) The techniques of both batch testing and continuous testing have been used to investigate this relationship. The technique of continuous testing, in which steady-state conditions are established, permits direct investigation of the above equation. In the case of batch testing, C is decreasing continuously

Jan 1, 1961

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By N. M. Langdon

INTRODUCTION. IN considering the magnificent success of Mr. Gayley's Bold experiment of applying dry blast to the blast-furnace, whereby , saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether, still further economy in fuel is possible, and, if so, how it is to be attained? The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation,. tinder various conditions, of a number of furnaces, for which such information has been worked out., should enable us to form some conclusion on the subject. The tables and calculations given below cover the operations of several furnaces reported in our Transactions; also the two furnaces using natural and dry blast in ,Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces.. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated. for A and B in Table III. are those given by Professor Richards; except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table III. for comparison with C and D.)

Oct 1, 1909

By Charles L. Morgan

In June 1996, the United Nations International Seabed Authority opened shop in Kingston, Jamaica as an autonomous international organization charged with the administration of seabed mineral developments in all areas beyond national jurisdictions. The Authority is a consequence of the 16 November, 1994 entry into force of the 1982 United Nations Convention on the Law of the Sea (UNCLOS) and the 1994 Agreement relating to the Implementation of Part XI of UNCLOS. The total seabed area included within the Authority?s purview has yet to be assessed accurately, but clearly constitutes the largest single jurisdiction on the planet. The Authority is governed by legislative bodies called the Assembly and the Council and an administration called the Secretariat. The Assembly includes representatives of the 132 member states which are currently parties both to UNCLOS and to the 1994 Agreement. These member states directly fund the operations of the Secretariat. They include most of the world?s developed nations, island nations, and others among the 188 independent countries which are members of the United Nations. Notably absent are the United States and Canada, which are the only developed coastal states not represented. The Council is a 36-member subset of the Assembly representatives selected through a somewhat involved process designed to achieve a balanced representation of the specific interests of the members. Ultimate responsibility for the Authority?s actions resides in the Assembly, but most initiatives originate in the Council. Also included in the Authority are two subsidiary advisory bodies, the Finance Committee, which reviews the Secretariat?s budget, and the Legal and Technical Commission, which evaluates claims and drafts technical regulations. The Secretariat itself includes a staff of about 30, including 15 highly qualified and competent attorneys, accountants, engineers, and scientists. Details describing the composition and activities of these bodies can be found at the Authority?s website (http://www.isa.org.jm).

Jan 1, 2000