Search Documents

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

Selective Removal of Arsenic from Acid Mine Drainage Containing Ferrous Ion Using Sulfide Precipitation Method

Sep 13, 2010

By Carolina Rouillon

El presente documento señala dos experiencias aplicadas en la mina Yanacocha y Pierina exitosas donde se emplea las geomallas como parte del mejoramiento de suelos blandos con la finalidad de distribuir uniformemente las cargas impartidas por los grandes equipos mineros hacia la subrasante de mina típicamente conformada por suelos con alto contenidos de limos y arcillas húmedas y saturadas. Asimismo, los beneficios obtenidos por usar las mallas, no se limitan al ahorro en costo material de relleno, sino que se logra un mejor desempeño- en tanto optimiza la superficie de circulación de los vehículos mineros, reduciendo los tiempos de operación, así como prolonga los períodos de reparación y mantenimiento.

Sep 21, 2013

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By D. M. Loring

Radon progeny have been a health and safety concern for miners since the mining of radioactive minerals began. Through the ?nuclear age?, it has become better understood and the regulations have become more robust. Ventilation and control practices have improved, thus reducing miners? exposures. This paper provides an overview of radon in mining, the progress of the regulations, and discusses some of the uranium miner studies that contributed to the knowledge of the pathology of radon.

Jan 1, 2009

By Bibby P. A, Leupen R. A

A 24,300 tonnes per year state of the art Silicon smelter is being constructed for Barrack Silicon Pty Ltd at Kemerton, 20 kilometres north of the City of Bunbury in Western Australia. The plant is designed for the reduction of high purity quartzite lump to metallic silicon in two 27MVa Demag submerged arc electric furnaces. The primary reductant, a high purity charcoal, will be manufactured at the plant from locally sourced jarrah wood waste (Eucalyptus Marginata). Commercial silicon production is scheduled to commence in October 1989. Keywords: Silicon, Smelter, Quartzite, Furnace, Charcoal, Jarrah, Wood, Eucalyptus Marginata.

Jan 1, 1989

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

This appendix contains the list of equipment selected for the capitol cost estimate, with the respective quotations from their vendors/manufacturers. A vendor response report along with a separate equipment and motor list has been included in the first part of this appendix.

Jan 1, 1979

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007