Search Documents

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By S. Henley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: The database: a pre-requisite for large-scale use of AI in mining). Artificial intelligence is a term which has been widely applied to different techniques including rule-based systems using inductive and deductive logic algorithms, neural networks, learning systems and genetic algorithms. In principle it should be applied to adaptive statistical techniques. Some of these applications have been coded in languages which are specifically suited to the novel requirements of AI but are not easy to integrate with more traditional computing methods. Efforts have been made to bridge the gaps, particularly with database management systems and such efforts at integration should provide the key to future success in the application of AI. A field which has been termed "knowledge engineering" cannot be credible as such if it fails to provide easy access to raw materials of "knowledge" i.e. the data residing in databases. In the mining industry there are a number of significant areas in which AI could usefully be applied throughout the industry, but its advance is slow because of the lack or inefficiency of such database links. Current development of object-oriented database systems for geology and mining holds out hope for such integration in the foreseeable future

Apr 1, 1994

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By Michael Harley, E. Guy Charlesworth

"Abstract - Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

By H. F. Letient, D. C. Johnson

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid rock drainage (ARD) and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid-generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid-generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings toward the end of the mine life, thereby generating a non-potentially acid-generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-potentially acid-generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid-generating rock and to be flooded at the end of mine life.

Jan 1, 2004

By Douglas B. Silver

Super Cycle future The final topic is mining?s future. The most important questions are ?How much longer is the Super Cycle going to last? What should we expect to see going forward? How will the Super Cycle end?? Three possible scenarios follow. Scenario one: Super Cycle has peaked Kathy Casey-Kirschling is officially the first Baby Boomer. She was born Jan. 1st, 1946. If you google ?first baby boomer,? she?s the one that shows up. A Baby Boomer is anybody born between 1946 and 1964. In the United States, it represents about a quarter of the population ? approximately 76 million people. The Baby Boomer generation is going to change the economics of the world because there are so many in the generation. A review of spending patterns indicates that the largest amount of discretionary spending occurs between the ages of 49 and 52. Retired people tend to live on fixed incomes so they have less discretionary income. They also tend to downsize their house, which may contribute to the housing glut and the need for a lot less metal. Therefore, the upcoming retirement of the Baby Boomer generation could result in a massive shift in economic spending resulting in the peaking of the Super Cycle. Figure 1 is an index graph from the Toronto Stock Exchange (TSX). The index has recently peaked. A lot of people see that as a sign that bad things coming our way. A careful review of different commodity prices also suggest that the peak has occurred and it does not seem to matter which commodity prices are considered. Copper prices have seen a peak as have nickel prices. Nickel and molybdenum displayed the same trend with a peak in 2005 as did zinc. Uranium, which has single-handedly tried to behave like the dot com craze, has also peaked.

Jan 1, 2008

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

THE Broken Hill mining field, approximately 31 miles in length, is at present being exploited by seven companies, viz. : North Broken Hill Limited, Junction North Broken Hill No Liability, Broken Hill Proprietary Block 14 Company, Broken Hill ProprietaryCompany Limited, Sulphide Corporation Limited, Broken Hill South Limited, and Zinc Corporation Limited.The variation in size and shape of the ore-bodies in the mines of these companies, together with the many alterations in pitch and dip, necessitates differences in methods of mining, each company working out its problem in its own particular way.In the matter of chute construction for the handling of the ore broken in the stopes, each mine belonging to the above companies has adopted a style particularly its own, though it may be said that one or two of the types approximate very closely to each other, slight minor differences only being noticed in the design. It is the purpose of this paper to give a brief description of the principal types of chutes now in use in th,e various mines on the field, and in doing so they may roughly be classified into three groups, viz:1. Bulk Chutes, 2. Circular Chutes, 3. Square-set Chutes.The Bulk type of chute is used in the North and British mines of the North Broken Hill Limited, the Central and Junction mines of the Sulphide Corporation, the South Blocks mine of the Zinc Corporation, and the Block 14 mine.The Circular type of chute is used by the Broken Hill South mine and the South Blocks mine.The Square-set chute is used in the Proprietary mine, the Junction North mine, and occasionally in other mines where the square set method of mining is a necessity, and more particularly as mullock passes.

Jan 1, 1925

By S C. Labram, A Stabile

"Modern train load out stations are becoming faster and have the ability to load a 100 wagon train in less than three hours. At 70 metric tonnes per wagon, that is an average fill rate of 2333 t/h and considering the train is continuously moving, the instantaneous feed rate into the wagon is in the region of 4200 t/h.The main feed conveyor that maintains the level in the surge hopper, above the final weigh hopper, operates in excess of 5000 t/h to ensure uninterrupted charging of the weigh hopper to not disrupt the train loading operation.To avoid demurrage costs (a charge by the Rail Operating Company for exceeding the contractually agreed loading time) the train has to be handled speedily and efficiently and spend the absolute minimum time at the loading facility. Everything else has a much lower priority, including sampling.Thermo Fisher Scientific’s brief was an engineering, procurement and construction management (EPCM) contract to provide a sampling scheme adjacent to the prepurchased and predesigned load-out facility, but which interfaced seamlessly with the loading system of the trains and provided the following: an instantaneous particle size distribution (PSD) result for each truck loaded, and a final PSD for the total train prior to the train leaving the loading facility a crushed (-3 mm) composite sample for chemical analysis for the whole train a composite physical analysis sample for the whole train.The design presented some interesting challenges to our team, but the end result is a system that not only ‘stands alone’ but interfaces seamlessly with the loading system. This paper discusses the design itself and potential improvements to future systems.CITATION:Labram, S C and Stabile, A, 2017. An automatic sampling methodology to determine contractual particle size distribution in rapid train load out stations, in Proceedings Eighth World Conference on Sampling and Blending, pp 229–234 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977