Search Documents

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

A substantial proportion of current and historic West Coast gold production comes from deposits situated around the margins of æice ageÆ glaciers. Gold has been eroded and transported by glacial ice then deposited in till and outwash gravel. The interplay between fluvial and glacial processes, climate, basement geology, tectonic uplift, sediment supply and sea level dictates many aspects of the development of the West Coast landscape. The way in which the external forcing factors interact is crucial in determining the gold content of placer deposits in this region. The following is an outline of some of the factors that influence the gold distribution in vicinity of glacial margins.

Jan 1, 2000

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

By Davenport, Edmund S.

THE specific aim of this work has been to study certain forms of internal deterioration which occur in tungsten filaments when subjected to high temperatures under various conditions, and to determine the cause of such deterioration. This would naturally lead to a consideration of methods of control or means of prevention of the phenomena. The deterioration was first noticed as a peculiar condition in the grain boundaries of certain tungsten filaments which had been burned t for long periods in lamps. In these cases it was noted that the grain bound aries contained a number of minute black dots which were at first thought to be non-metallic inclusions. It was demonstrated later that these dots or pits, as they were designated, could be readily produced by burning filaments in an atmosphere of flowing hydrogen. This method was convenient and adequate for the purpose, and was adopted for most of the work discussed in this paper. The evidence accumulated to date indicates that these pits arc actually small voids between the grains. The purpose of this paper is to, present the information on this interesting subject gathered during a period of about 3 years. As applied to tungsten, the subject appears to be of considerable importance, experience having shown that this pitting is frequently associated with poor performance of filaments in lamps.

Jan 1, 1927

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By R. N. Powell

The Pipeline ore body was discovered in March 1991. The construction of the new mine and mill did not start until early March of 1996. Upon completion of permitting and corporate project approval, the 289 million USD project was “fast tracked”. The commissioning began 11 months after start of construction and the project ended 40 million USD under the budget figure. The objective of this paper is to review and highlight the Pipeline Project history from discovery, design, lawsuits, permitting, and re-design through to current - 1998operating practices. Particular emphasis will review the process design, design mistakes, and design successes. The paper will review project history, feasibility, design concepts, operator training, construction, financial and the current operation. Additional discussion will review what design features worked and which did not work within the process plant.

Jan 1, 1999

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By D. Richardson

Presentation Objectives ?Demonstrate the utility of 3D modelling for visualizing exploration data ?Demonstrate the target generation ability of 3D model query methods Exploration Criteria -Example Given the Geology of Sudbury What Are Our Exploration Criteria? (selected examples) ?Geometry ?Trends ?Lithology ?Proximity to Sulphides ?Length and Grade of Anomalous Mineralization ?Distance from Footwall In Addition ?Geophysical Criteria ?Economic Criteria ?Amount of Available Space ? Depth

May 1, 2006

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By James K. Richardson

STATISTICAL evidence shows that continued efforts made by Government and industry to make mining safer during the last two decades have had most favorable results. In the copper-mining industry an accident frequency of 146 per million man-hours worked in 1925 dropped 71 per cent by 1945 to 43. This downward trend was relatively consistent except for a high period in 1937 which was probably due to a resumption of large-scale operation with many untrained miners. The iron-mining industry showed a similar trend, but at the relatively lower accident frequency of 66, which dropped to 24 in 1945. The close relationship between the steel and iron-mining industries may be one reason for the lower accident frequencies, because the steel industry is noted for its greater recognition of the fact that safe working conditions are an important part of labor-management relations.

Jan 1, 1948

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress,

Jan 1, 1965

During the period January 1, 1977 through July 31, 1977, 5 percent (264,000 tons) of U.S. capacity was closed due to power curtailments in the Pacific Northwest because of the shortage of water. During July, one plant in Tennessee cut production by 50,000 tons annually due to a power reduction by the Tennessee Valley Authority. Full capacity production was resumed at a West Virginia smelter during September. If demand for aluminum is strong it seems likely that aluminum supply during the remainder of 1977 and in 1978 will be tight. The price was increased 3¢ per pound to 51¢ per pound effective March 28, 1977, and by an additional 2¢ per pound to 53¢ per pound, effective July 5, 1977. New projects and expansion of existing facilities are planned by Australian aluminum companies over the next 2 to 3 years. The companies listed have committed themselves to spending approximately A$801 million: Alcoa of Australia Ltd. -New alumina plant at Wagerup, south of Perth. Darling Ranges bauxite is located near the proposed project. A$650 million. Coma 1 co Industries Pty. Ltd. -Increase bauxite mining capacity and upgrade or replace other facilities at its Weipa mines on Cape York Peninsula region of Northern Queensland. A$81 million. Alcan Australia Ltd. -Expansion program that will increase capacity of the Kurri Kurri aluminum smelter north of Sydney about 50 percent, and improvement of other facilities at the plant. A$70 million.

Jan 1, 1977

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By S. D. Hill, G. E. McClelland

To maximize productivity and improve minerals processing technology, the U. S. Department of the Interior, Bureau of Mines, is investigating a particle agglomeration technique as a means of increasing the percolation rate of leaching solutions through heaps of clayey or finely crushed, low- grade, gold-silver ores. Bench-scale and pilot-scale experiments conducted on different ores indicated that the percolation rate of cyanide leaching solution was enhanced markedly by mixing the ore with a binder, such as lime or portland cement, moistening the mixture, then mechanically agglomerating and aging the feed prior to heap building and leaching. In addition, the rate of silver and gold extraction markedly increased without sacrificing total recovery of values. The use of concentrated cyanide solution instead of water during the agglomeration procedure substantially decreased the leaching time required to obtain maximum recovery. Results from bench-scale and pilot-scale experiments using the particle agglomeration technique are discussed.

Jan 1, 1981

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930