Search Documents

By J. R. Thoenen, B. H. Clemmons, A. H. Reed

"INTRODUCTION AND SUMMARYOverall red-ore reserves in the Birmingham, Ala., area were estimated in 1910 by E. F. Burchard 4/. Since then mining has progressed into areas classed by Burchard as ""unavailable for exploitation"" under conditions existing at that time. This is understandable when it is considered that red iron ore was valued at $1.19 a gross ton at the mine in Birmingham in 19102/ and by 1948 had risen 300 percent; 6/ that skips had replaced cars in slope haulage; that mechanical loading and rubber-tired haulage had replaced hand loading and mule or locomotive haulage; and that other more efficient mining methods had been introduced. Intensive study during the intervening 40 years has been given to ways and means for upgrading the low-grade ores in the area and combining or blending them with raw red and brown ores for improved blast-furnace feed.It is reasonable to expect that future progress in mining efficiency and increased knowledge of the beneficiation characteristics of marginal ores will permit extraction of red-iron minerals now considered uneconomic.The Bureau of Mines has undertaken to restudy iron-ore reserves of the Birmingham area to determine what tonnage and grades of mineral are present; what is necessary to make them amenable to mining; what further advancement is possible in beneficia¬tion methods; and where increased production may be obtained in the area if and when required. This study has been underway for the past 2 years, but research into the beneficiation of marginal ores has been in progress at the Southern Experiment Station for the past 30 years. Many results of that research have been adopted in commercial practice in the area. Other results have not been published but are pre¬sented here in condensed form as an important factor in assessing marginal deposits with respect to their importance as ore reserves.An interim discussion of the salient features of past history and progress, as well as the data developed during the years of research in beneficiation at this station and the present field investigation, will make for a better understanding of the present position as well as be useful in evaluating future potentialities. Discussion in this paper is confined to the main Birmingham Basin area, which contains the largest concentration of hematite ores in the district."

Jul 1, 1953

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

By Martin J. Gavin

The results of investigations of the oil-shale resources of the United States were first published by the United States Geological Survey in 1915.1 Other reports 2 have followed. These reports, investigations by private individuals and corporations, and the beginning of the development of an oil-shale industry in this country have aroused considerable interest in the possibilities of these shales as a commercial source of hydrocarbon oils. The Bu- . reau of Mines bas appreciated these possibilities, and since 1916 one or more of its engineers have given all or part of their time to investigations relating to the treatment of oil shales. A short pamphlet a containing general information on the possibilities of oil shale in this country, particularly the shales of the Rocky Mountain district, has already been published. This pamphlet gives methods for assaying the shales of oil and ammonia and contains a bibliography for the use of those desiring to search the literature.

Jan 1, 1924

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By D Bruce

OZ Minerals’ Carrapateena mine is a Sublevel cave mine located in South Australia, approximately 160 km north of the regional centre of Port Augusta. Carrapateena commenced underground development in 2016, with production commencing in 2019 and ramping up to 4.25 Mtpa by December 2020. In pursuit of continual improvement, the Carrapateena mining team sought to identify how it could better interrogate its current productivity levels and its drivers (root causes). During this process the team were confronted by a disconcerting number of different opinions (which often conflicted) on our actual productivity performance which led to a need for review. Although reliable data and a well-designed time utilisation model (TUM) existed, it was still unclear what actions needed to be put in place to improve productivity. This was for the following reasons: • Data sources were disparate unless significant effort was applied to compile them. • Data sources were not available in a format that could be easily viewed or analysed. • General understanding of the data which was collected and how it could be used was poor. • Process of regularly analysing performance and forming tangible actions to improve was lacking rigour. A project was then started with the goal to fix the areas stated above. An initial requirements gathering exercise was undertaken to identify key data sources for site which returned a staggering 42 known systems which were then shortlisted to the key systems that contained operational data and could generate tangible improvements when analysed. This paper discusses the approach to selecting the OZ Minerals Insights Hub as the chosen platform, and the effort and collaboration between cross-functional departments that was involved in transforming the data so it could be displayed in a useful way. The data sources identified included a fleet management system, two planning databases, a control system historian, and a mobile fleet machine data system. New processes were also introduced to digitally capture daily commentary; this was achieved utilising SharePoint Forms. Data pipelines were then developed in the Insights Hub platform to automate the ingestion and transformation of the raw mining data into curated data models for end user consumption. Tableau dashboard packages have been created to support facilitation of short interval control, daily review meetings, and weekly review meetings as well as data analysis of key equipment and locations. These dashboards visualise the mining data models in a form that provides the user a clear picture of what has occurred, why it has occurred, and where to focus improvement efforts. This has resulted in a team which is more accountable, more equipped to assess the root cause of performance, and more regularly able to make data driven decisions. The next step? To build this out from Mine to Mill and create a data indexing tool which will drive self-service reporting, a data agnostic platform and predictive tools that help our people continue to be one step in front.

Mar 29, 2023

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By C. R. Carpenter

A dynamic gas-mixing system assembled by the Bureau of Mines for the generation of precise gas mixtures from sources of concentrated or pure gases and diluent gases is described. A set of electronic mass flow controllers with maximum flows ranging from 10 to 5,000 ml/min, a so-called Pure Air Generator, and gases in cylinders are used to generate differing gas concentrations. The repeatability of the delivery rate of a flow controller, measured on different days, has a precision of 0.3 pct of the setting. This dynamic gas-mixing system reduces the cylinder inventory and the demurrage charges for special gas mixtures. Gas mixtures that cannot be shipped commercially, such as flammable mixtures of methane in air, can be conveniently prepared by this system. The maximum dilution ratio is 2.5 x 104. Thus, gas mixtures can be made over a wide range of concentrations, from the percent region (by dilution of a pure single-component gas) to fractional parts per million (by dilution of a premixed standard, e.g., a 1,000-ppm mixture). This system is especially useful in determining the response of gas detection devices over the entire range of their measurement. Because the controllers are voltage controlled they lend themselves easily to automated control using computer-based systems.

Jan 1, 1983

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northernPaparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By K. M. Tompson, R. L. Armstrong, C. I. Godwin

"Tungsten skarn deposits on the Clea property in the Selwyn Mountains, Y. T., are related genetically to a quartz monzonite stock, about 500 metres in diameter at the surface. Lower Paleozoic sedimentary rocks are metamorphosed for a distance of 3 km from the stock. Tungsten-bearing skarn mineralization within the altered sedimentary rocks is of two types: sulphide-rich pods and calc-silicate beds. The most significant scheelite concentration is in calc-silicate beds near or adjacent to the quartz monzonite stock. Discordant K-Ar and Rb-Sr isotopic dates indicate that the stock is probably of early Late Cretaceous age, 94 Ma or slightly older, and that it cooled slowly. High initial 87Srl86Sr ratios and disequilibrium relationships between K-jeldspar phenocrysts and groundmass minerals in the porphyritic phase of the granitic rock , and between different granitic rock specimens, indicate contamination of crystallizing magma by old sialic continental crust which extends westward under the Selwyn Basin.This study is significant to regional tungsten exploration. Granitic rocks associated with tungsten deposits, in this part of the Canadian Cordillera at least, appear to have specific isotope characteristics that indicate they were generated at a specific time and in a particular way.IntroductionThe Clea tungsten skarn property (Fig. I) is owned by Canex Placer Limited, and lies in the Selwyn Mountains (Bostock, 1948) near the eastern margin of the Selwyn Basin (Wheeler and Gabrielse, 1972), Yukon Territory. The property covers a 20-square-mile area centered near latitude 62°47 ' north and longitude 129°52' west, and is accessible by helicopter. An airstrip and the terminus of a summer-use gravel road at MacMillan Pass, Yukon, are about 20 miles to the northnorthwest.This paper deals mainly with the geochronemetry of granitic rocks from a stock associated with tungsten mineralization on the Clea property. We show that these rocks have specific characteristics that not only define the genesis of this stock, but also have significance for regional tungsten exploration around plutons in the Canadian Cordillera."

Jan 1, 1980

Size Separation Pretreatment and Alumina Recovery from Bayer Red Mud

Sep 13, 2010

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the information needed to use the Wearing Hearing Protection Properly 3-D training reel. It offers practical suggestions on how to use the reel as a training aid, performance objectives for deciding if the training is appropriate for your needs, and discussion notes that provide additional information to the user. The 3-D reel was designed as a self-teaching aid that drillers and others who work at a drill site can use wherever the opportunity for such training presents itself. The latter could be a company preshift requirement or a tailgate session where workers would have an opportunity to view and discuss the reel. It could also be an individual looking at the reel in a pickup truck prior to beginning work at a drill site. The 3-D training reel is versatile in that it can be used for a small group of persons or for a single worker. For any of these situations, information is transferred to the individual by viewing each of the seven colorful, in-depth 3-D scenes and relating the words that appear in each scene to what is depicted in the visual. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 11, 2004

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

The National Mining Hall of Fame and Museum (NMHF&M) will celebrate its 25th anniversary on Sept. 22, 2012 when the 2012 class is inducted during a special ceremony in Las Vegas, NV in conjunction with MINExpo 2012. The NMHF&M will induct four men representing the equipment manufacturing, minerals exploration, copper and coal sectors of the mining industry. The diverse cross-section of mining industry giants joining the hall of fame include Glen A. Barton, J. David Lowell, Samuel Newhouse and John Cleveland Osgood. They will join 214 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 25th Silver Anniversary Induction Banquet & Ceremony. These men were selected for being visionaries, leaders and ambassadors within their own sectors and across the industry at large.

Jan 1, 2013

By M. Mikolás, L. Pomothy, K. Špakovská, M. Vanek

"Enterprises are faced with increasing economic competition and managers are obliged to look for methods that will ensure a competitive edge in their companies’ markets. These methods include managerial concepts that employ common sense and are low cost. One of these approaches is the KAIZEN methodology, of Japanese origin; kaizen means continuous improvement (CI) when translated. A mining company, despite some of its idiosyncrasies, is just an enterprise where the application of KAIZEN can be advantageous. The company investigated, OKD, is the only domestic producer of hard coal in the Czech Republic and operates four mines that produce 11 Mt of coal annually. The OKD management team opted for KAIZEN as their principal method of continuous quality improvement. This paper suggests ideas for development and application of processes that provide for continuing improvement of production and management. The authors have taken the OKD Company to be their benchmark in the field of mining activities. The paper also focuses on possible difficulties accompanying the introduction of CI sustainable methods. Three years of application of CI methods has increased the income of the company by almost US$38.1 million, which provides a strong argument for continued application."

Jan 1, 2015

By P Standish

Qualitative risk assessment methods are not well suited to considering complex systems and potential interactions of new technology. As part of supporting tier one mining organisations and international industry groups, the author and colleagues have innovated processes to help provide better solutions to sites/companies considering a move to implementing proximity detection and collision avoidance systems. The process identifies required operating states for the system. By applying a combination of research and team-based analyses, a rigorous identification of credible failure modes which could cause these states to be lost, is identified. Finally, required business inputs, expressed in practical terms are distilled from regulator, industry, organisation and site in a way which clearly addresses the failure modes and so retain the required operating states. These business inputs identify improvements for site arrangements (EMESRT levels 1 to 7) before identifying functional requirements for technological collision avoidance solutions (levels 8 for advisory and 9 for autonomous). The paper presents a case study synthesised from multiple sites analyses and will provide guidance on where to find additional resources to assist in making the best possible transition to better equipment and road network solutions.

Jun 22, 2022

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960