Search Documents

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By H. H. Kellogg

The thermochemical properties of molten solutions in the binaries Cu-Bi, Cu-Sb and Bi-Sb, as well as the ternary Cu-Bi-Sb, have been correlated and described in mathematical form by use of the associated species concept combined with the three-suffix Margules equations to account for the non-idea 1 behavior of the solution species. Agreement of the correlations with experimental data is excellent (relative deviation of less than 2.5% in the values of the activity coefficients) in most cases. The correlations are applicable over the entire composition range of each system, and in the temperature range 700°-1250°C.

Jan 1, 1985

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By C. B. Piazzarollo

Ceramic materials exhibit dispersion results after being subjected to various levels of stress, from the point of view of mechanical strength. With the focus on sustainable development and to improve the strength of these material, was incorporated ornamental rock waste into clay in up to 10% in mass to conform some samples, that was fired to 750ºC, 850ºC and 950ºC and submitted to technological tests. This paper presents an analysis of the technological properties of the samples through the use of Weibull statistic to determine which the best firing temperature for these red ceramic materials. The Weibull Modulus indicates a greater homogeneity for samples with 10R at 950ºC.

Jan 1, 2015

By R. Harris

Blister copper melts of 800 g to 1000 g containing less than 1 wt % S and up to 3 wt % Ni were desulfurized at 1523 K in air or by a pure oxygen jet blown at 75,500 and 1000 cm3/min, from 1 cm above the melt. Rates of desulfurization and oxygen pickup were measured and visible surface phenomena were photographed and videotaped. It was observed that SO2 was evolved from Cu-S melts in a manner reminiscent of the effervescence seen in carbonated drinks. The effervescence lasted up to 20 minutes and resulted in the ejection of material up to a height 50 cm above the melt surface. Sporadic discharge of large bubbles was also observed in a Ni containing melt top-blown with oxygen at 1000 cm3/min. The Cu-S melts top-blown with oxygen experienced faster sulfur elimination as compared to stagnant melts exposed to air and experienced only a single period of turbulent SO2 evolution, which occurred almost immediately after oxygen injection commenced. The Cu-S melts exposed to air experienced multiple episodes of effervescence. The stagnant blister copper melt containing nickel did not exhibit effervescent behaviour and experienced a lower rate of sulfur elimination compared to Cu-S melts tested under similar conditions. The present article examines the role of surface phenomena in determining the observed behaviour.

Jan 1, 1999

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

By Dan Mancuso

This case study is an example of how Encyle/Texas, Inc. (a subsidiary of ASARCO) responded to various socio-economic forces by converting an idle zinc hydrometallurgical refinery into a metals recycling facility. The facility accepts metal-laden process waste streams and produces various "synthetic ores" which are sold back to industry. Acceptance and reactions by industrial, political, economical and regulatory interests towards the project are also discussed.

Jan 1, 1992

By Jewel A. G. Gomes

Lead has long been an USEPA priority pollutant and an important environmental and health concern because of its toxicity at ppb levels. In light of health and exposure data for lead, the EPA has set standards for Maximum Contaminant Level (MCL) and a MCL Goal (MCLG) as 15 ppb and 0 ppb, respectively. An accurate and rapid measurement of lead in the field remains a technical challenge. In this work, a relatively new method of deploying a nanoband electrode system using anodic stripping voltammetry has been optimized by changing deposition potential, electrolyte, and plating time used for the measurement of Pb(II) in water samples. Green rust has been proven to be an efficient intermediate matrix for removal of lead contaminants. We also report here the removal efficiency of lead using green rust produced by electrocoagulation, both directly and indirectly. Lead containing floc was also characterized through XRD, SEM, and EDAX techniques.

Jan 1, 2008

By Eva B. Kisvarsanyi

An Early Proterozoic orogenic terrane of metasedimentary and metaigneous rocks underlies Nebraska, Kansas, and Missouri. Middle Proterozoic epizonal terranes of anorogenic granite and rhyolite, a known metallogenic province partly exposed in southeastern Missouri, overlap the orogenic terrane on the south. These Proterozoic terranes, covered by less than 1,000 meters of Phanerozoic strata, contain a virtually untapped source of mineral wealth and are one of the last frontiers for geologic exploration in the continen-tal United States. Petrographic study of subsurface samples is a powerful tool in the identification of favorable host rocks for a variety of ore deposits.

Jan 1, 1987

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By Katri Avarmaa

Aluminum and copper are large volume metals in electronic appliances, while tin and indium exist as common minor elements. All of these non-ferrous metals are aimed to be separated and recycled from the end-of-life electronics into non-ferrous scrap fraction(s), and further through pyrometallurgical and/or hydrometallurgical processes to pure metals. Depending on the mechanical pre-treatment processes, aluminum and copper liberation from each other varies. This study focuses on the influence of alumina on indium and tin distributions between copper alloy and iron silicate slags with 0, 9 and ∼16 wt% of Al2O3. The experiments were executed with an equilibration-quenching-EPMA technique in an oxygen pressure range of 10−10–10−5 atm at 1300 °C. The metal-slag distribution coefficient of indium remains constant as a function of alumina in slag, while that of tin increases. Therefore, aluminum in feed or alumina addition to the slag improves the recovery of tin into copper. Nevertheless, oxygen pressure has clearly more significant influence on the behavior of both the metals in the smelting conditions.

By Robert De Saro, Willis Bateman, Ramesh Jain

A Vertical Floatation Melter (VFM) has been developed (sponsored by DOE) which simultaneously decoats and melts organic laden scrap in a single unit. Scrap aluminum is fed into the top of the VFM where it falls through a cone. Hot gases flow upwards through the cone, imposing a variable drag force on the scrap. Equilibrium is reached in which the scrap weight equals the drag force and the scrap becomes suspended. The gases strip off and vaporize the organics. Next, the scrap reaches a liquid state, taking on a more aerodynamic teardrop shape, allowing it to fall into a holding furnace. Heat transfer coefficients are 10 times higher than that of a conventional furnace, allowing rapid melting at a low gas temperature. Typical energy use is well under 2,324 joules/g (1,000 Btu/lbm) with a metal yield from 92 to 98%. This paper reports on the operation and data of a 453 kg/hr (1,000 pph) pilot-scale VFM.

Jan 1, 2000

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By Douglas Robinson

This paper describes technical work done to develop a Spouted Bed Electrode Cell into a commercially viable Electrowinning Cell; (a previous paper has been presented at the ECS meeting in Paris in May of this year, with a more general overview of the cell, [1]). The studies have included hydrodynamic tests to understand the criteria for the circulating flow of metallic beads in the cell, particularly in the region at the entrance to the draft tube, and electrochemical tests to find a suitable diaphragm for extended time electrolysis. Various patent pending features were developed including a double nozzle to allow for automatic stopping and restarting of the bed, an arrowhead shaped draft tube to control the flow of beads into the entrance to the draft tube, a roof-top shaped device to control the flow of beads out of the top of the draft tube, an overflow weir to allow the continuous recovery of beads from the cell, and a family of diaphragm fabrics for extended operation. Prior to the identification of the diaphragm material, short circuits would develop within a few hours. A pilot scale cell was operated for three days, with continuous operator attention, and then for ten days with operator attention only on day shift. The cell is currently advancing to the next stage of development which will involve continuous testing in a commercial copper electrowinning facility.

Jan 1, 2003