Search Documents

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By Frank E. Chase

Clay veins, also referred to as clay elastic dikes, have been responsible for numerous underground injuries and fatalities. These hazardous structures are also responsible for increased production costs during all phases of mining. For these reasons, the Bureau of Nines has investigated the physical characteristics of and roof instability problems associated with clay veins in order to make support and other mining recommendations. In addition the occurrence and origins of clay veins were examined to determine whether or not the structures could be projected into unmined portions of the coalbed. This investigation included portions of the Arkoma, Illinois, Northern Appalachian, Southern Appalachian, and Uarrior Coal Basins. Virtually a11 clay veins observed or documented occurred in the Illinois and Northern Appalachian Basins. Observed clay veins ranged in sire from 1 inch to 16 feet In cross-section and were found under shale, siltstone, sandstone, and limestone roof rock. Individual clay veins were predominantly composed of claystone; however, limestone. siltstone. and sandstone infilled clay veins do occur. Clay vein formation has been associated with the infilling of fissures which result from compressive, tensile, or shear ground failures. These gaping fissures were propagated by compactional processes and/or tectonic stresses active during and subsequent to coal iff cation. Associated fault, fracture, and slickenside planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance the roof is segmented into cantilever beams causing unstable conditions. Therefore, the strata on either side of the clay vein must be bolted and strapped together to form a beam.

Jan 1, 1984

By Stephen C. Tadolini

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these ?simple? devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors? opinions of course).

Jan 1, 2006

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Christopher Mark

"Many problems in rock mechanics are limited by our imperfect knowledge of the material properties and failure mechanics of rock masses. Mining problems are somewhat unique, however, in that plenty of real world experience is generally available and can be turned into valuable experimental data. Every pillar that is developed, or stope that is mined, represents a full-scale test of a rock mechanics design. By harvesting these data, and then using the appropriate statistical techniques to interpret them, mining engineers have developed powerful design techniques that are widely used around the world. Successful empirical methods are readily accepted because they are simple, transparent, practical, and firmly tethered to reality.The author has been intimately associated with empirical design for his entire career. But where his past papers have described the application of individual techniques to specific problems, the focus of this paper is the process used to develop a successful empirical method. A six-stage process is described:1. Identification of the problem, and of the end users of the final product2. Development of a conceptual rock mechanics model, and identification of the key parameters in that model3. Identification of measures for each of the key parameters, and the development of new measures (such as rating scales) where necessary4. Data sources and data collection5. Statistical analysis6. Packaging of the final productEach of these stages has its own potential rewards and pitfalls, which will be illustrated by incidents from the author’s own experience. The ultimate goal of this paper is to provide a new and deeper appreciation for empirical techniques, as well as some guidelines and opportunities for future developers."

Jan 1, 2015

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Thomas M. Brady

The Spokane Research Laboratory/NIOSH and the University of British Columbia (UBC) geomechanics group are focusing on the development of safe and cost-effective underground design guidelines for weak rock masses having an RMR in the range of 15 to 45. Weak ground conditions, ground support, and mining methods used in several North American underground mines were observed. The RMR values were calculated to update both manned entry span design and non-entry stability graphs, plus a database on underhand mining methods was created to reflect existing North American mining conditions. The immediate rock mass was characterized and analyzed in terms of prevailing type of ground support, potential failure mechanisms, and rock behavior to define how existing design curves must be modified for the existing weak rock mass. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making sound economic decisions that will also ensure a safe working environment.

Jan 1, 2006

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By Thomas M. Barczak

With the development of the shield support, the primary requirement for successful ground control in longwall mining is to provide stable gate road and bleeder entries. Wood cribbing has been the dominant form of secondary support. However, the cost and limited availability of timber, along with the poor performance of softwood crib supports, has forced western U.S. mines to explore the utilization of other support systems. The recent success of cable bolts has engendered much interest from western operators. Several innovative freestanding support systems have been developed recently including: (1) "The Can"' support by Burrell Mining Products International, Inc., (2) Hercules and Link-N-Lock wood cribs and Propsetter by Strata Products (USA) Inc., (3) Variable Yielding Crib and Power Crib supports by Mountainland Support Systems, (4) the Confined Core Crib developed by Southern Utah Fuels Corporation; and (5) the MEGA prop by MBK Hydraulik. This paper assesses design considerations and compares the performance and application of these alternative secondary support systems.

Jan 1, 1996

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Greg Hendon

Various methods have been used to evaluate the effectiveness of shields in place. The most common method used is static recording of leg pressures by visually examining pressure gauges. In an effort to more closely examine the shield cycle and therefore the shield effectiveness, Jim Walter Resources has implemented a program of monitoring utilizing a polycorder system which is capable of recording convergence and pressure measurements on a continuous basis. This paper will discuss two longwall panels at Jim Walter Resources which have been monitored.

Jan 1, 1990

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By Bernard Woolley

The history of the use of calcium aluminates in mining is discussed including a review of very rapid hardening concretes, anchoring using cement capsules and pumped ground control systems. Specific reference is made to the long term performance of highly abrasion resistant orepass lining in South Africa and the use of rapid hardening materials for a range of applications in Australian coal mine where water infiltration creates difficulties or where rapid repair or return to service is required. The topics covered in detail are, high strength abrasion resistant concretes with a 20 year, 30 million ton ore pass life. Rapid reinstatement of wet and worn roadways using mineral dewatering and rapid roadway rebuild solutions, all in I maintenance shift. The different applications are illustrated using examples from operating mines.

Jan 1, 1997

By A. W. Khair

This paper deals with the analysis of pillar failure in a room and pillar mining operation of a deep underground coal mine. The incident here involved the failure of more than 100 pillars. The mechanism of pillar failure (bump/squeeze) has been studied in detail. The analysis consists of inmine eyewitness observations, laboratory experiments and analytical study of the pillar failure area using finite element technique. Results indicated that the mechanical properties of coal, roof and floor, geologic condition, and the method of operation have affected the mode of pillar failure. Hard roof and floor prevented roof caving and floor heaving in the gob area creating an inhomgeneous stress field on the pillar. This condition developed a yield zone and a core zone in the pillar. Progressive increase of vertical stress further increased the yield zone of the pillar and reduced the core pillar leading to a total squeeze of the pillar. However, the analysis indicated that the pillars were liable to bump provided any sudden shift of load occurred on the core pillar due to some dynamic shock imparted by a local failure of the immediate roof (slickenslided area) or during splitting.

Jan 1, 1986