Search Documents

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By T. McCallum

Crud is a common concern in SX processes and is formed as a complex solid stabilized emulsion of aqueous and organic.1,3 Crud formation is highly dependent on the amount of solids entering the circuit and is influenced by a number of other operational factors. A common practice for crud processing is interfacial pumping, wherein crud, organic, and aqueous are pumped from the settlers for treatment and utilizes a variety of equipment. These mechanical means of crud processing are effective, however, require significant processing time and require oversight to prevent the return of contaminated organic. Cytec has developed a unique crud treatment process utilizing both chemical and mechanical means to enhance the solid/liquid separation. The use of ACORGA CB? 1000 crud busting reagent allows a rapid separation of solids from the organic phase and provides similar volume recovery to current practices. The process allows operations to return clean organic back to the plant more efficiently and may enable operations to process more crud. In addition, the organic quality of the recovered organic is higher than that recovered by typical means, which can lead to operational cost savings.

Feb 27, 2013

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By H. Ikeda

INTRODUCTION [Slide 1] The Role of the MMAJ Ladies & Gentlemen, it is a pleasure for me to be able to make a speech at this SME annual meeting, representing the Metal Mining Agency of Japan. [Slide 2] Today’s Topics In my presentation today, I would like to divide my topics into four parts. First of all, I would like to describe the current situation of Japanese non-ferrous metal mining and mineral processing industries in Japan. Secondly, the supply and demand of non-ferrous metals in Japan. Thirdly, I would like to spare some minutes on the overview of overseas development by Japanese mining companies. Finally, since some people may not be sure what the Metal Mining Agency is or what this Agency, I would like to briefly introduce the Metal Mining Agency of Japan.

Jan 1, 2001

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By H. L. Barwood

Luminescence excited by electron bombardment, or cathodoluminescence (CL), is a very useful tool in petrographic examination of rocks, minerals and ores. Differences in luminescence colors and intensities allow detection and delineation of mineral species and composition zones difficult to separate visually by normal polarized light microscopy. The cold cathode CL chamber at Indiana University is used with a binocular microscope that has interchangeable attachments for a normal film camera, a digital camera and a fiber optic spectrometer. This allows imaging of the specimens as well as limited spectrographic analysis of the emitted luminescence. The chamber on this CL unit is large enough to accommodate several thin sections, polished mounts, grain mounts or rock slices at one time. Luminescence petrographic techniques were used to study alkali syenites and carbonatites from the Arkansas. Alkali feldspars in the syenites reveal a history of growth, fenitization and replacement through color and intensity differences. Primary orthoclase luminesces bright blue and is often zoned with a duller blue overgrowth of microcline. Fenitization of the feldspars is demonstrated by dull to bright red luminescence and replacement veins of albite often have a bright yellow green luminescence. Late microcline and perthites from the syenite pegmatites have a dull yellow to orange luminescence. Easily visible on this background of feldspars are grains of apatite (yellow), fluorite (violet), zircon (greenish), sodalite (orange) and mosandrite (green). Complex pseudoleucite syenites from Magnet Cove, Arkansas show similar minerals but also include xenolithic quartz (violet), manganwollastonite (bright orange), benitoite (intense blue) and lorenzenite (green). Carbonatites from Arkansas contain a wide variety of calcite textures and intensities of luminescence. Grains of carbonatite in well cuttings are easily distinguished from sedimentary calcites by their complex “flame” luminescence and the frequent presence of euhedral apatite grains (yellow). Apatite crystals separated from the Arkansas River Valley carbonatites by acid digestion show complex zoning. The cores of these apatites are yellow luminescing due to CL activation by Mn enrichment while the rims are violet luminescing due to REE enrichment. Complex zonation between the cores and rims is easily visible using CL.

Jan 1, 2001

By Stefan Mede

Robot Supported Moulding—this is the name of Herrenknecht Formwork’s entry to the world of automated segment production. What had been considered impossible for a long time, has been achieved by Herrenknecht experts together with the Swiss company Marti AG: unmanned segment production on the working line. The moulds open and close autonomously with the help of a hydraulic system. A robot cleans and greases the moulds at one work station and inserts the injection sockets at another. The next step will include further automation and digital networking of all processes from production to installation in the tunnel.

Jun 13, 2021

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011