Search Documents

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By E. Pizarro, A. Videla, G. Compan

One of the main problems related to mining investment decisions is the use of accurate prediction models. Metallurgical recovery is a major source of variability, and in this regard, the Chuquicamata processing plant recovery was modelled as a function of geomining-metallurgical data and ore characteristics obtained from a historical database. In particular, the dataset gathered contains information related to feed grades, ore hardness, particle size, mineralogy, pH, and flotation reagents. A systemic approach was applied to fit a multivariate regression model representing the copper recovery in the plant. The systemic approach consists of an initial projection of the characteristic grinding product size (P80), based upon energy consumption at the particle size reduction step, followed by a flotation recovery model. The model allows for an improvement in the investment decision process by predicting performance and risk. The final geometallurgical model uses eight operational variables and is a significant improvement over conventional prediction models. A validation was performed using a recent data-set, and this showed a high correlation coefficient with a low mean absolute error, which reveals that the geometallurgical model is able to predict, with acceptable accuracy, the actual copper recovery in the plant.

Jan 1, 2015

By S. P. Pereira

The mechanized mining cycle using loaders and shuttle cars had its peak in terms of usage in the mining industry during 1950 through 1960. In Brazil, this system is still used at underground coal mines in southern Santa Catarina coal basin. With the aim of investigating the benefits of a new mining scheme using the room and pillar method for these local mines, a computational simulator model was developed in order to investigate the mining cycle. This paper presents the methodology used to develop the simulator and the results that the simulation shows regarding impact of the proposed new scheme on mining productivity.

Jan 1, 2012

By L. Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pinpoint the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable temperature readings and gas analyses could have verified satisfactory activity. Hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: good record keeping is a necessity for collection of representative catalyst samples; reliable operating data is an inevitable starting point for all analysis; and trending of operating data is a must for plant optimization and troubleshooting. In addition, these catalyst management tools will give continuous updated knowledge of the catalyst status in each bed, providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking operating data, temperature optimization and good record keeping.

Jan 1, 2009

By F. Essrich

A quantitative rockburst hazard assessment procedure was introduced on Elandsrand Gold Mine at the end of 1994. It is currently used to evaluate the seismicity-related risk in production areas on the mine. Six parameters related to seismicity, geology, mining layout, and production are rated and results are used as a planning tool on a regular basis. The applied assessment can be considered successful in that it promotes awareness of the seismic hazard and provides an opportunity to address seismicity-related mining problems. A comparison between high risk panels and those working areas with rockburst incidents showed that high hazard ratings reliably forecast the occurrence of larger events in the following month but they do not necessarily predict those working places with rockburst-related accidents. From this one may conclude that high levels of seismicity do not coincide with high rockburst rates.

Jan 1, 1997

By John W. Harbaugh, Alfredo Prelate

The goal of the study described here is to develop objective. quantitative methods for estimating the outcome probabilities of exploratory oil wells. The study employs the 're-experience' approach, in which historical data are used in a manner which attempts to recreate the past. Our past experience, of course, is the principal guide to the future. To appraise present-day oil prospects, however, we must analyze prospects that have been drilled in terms of how these former prospects were interpreted before they were drilled. An analysis of how they are interpreted after they were drilled is an inadequate guide to the future because our hindsight knowledge is superior to our foresight knowledge. Objective calculation of future outcome probabilities, then, requires that we attempt to treat past information in a manner analogous to that in which we must treat present information in forecasting future outcomes.

Jan 1, 2014

By P. He

Abstract This paper introduces the test results of dark-gray calcium-shale, discusses the infection of strength characteristic and deformation characteristic due to the angle between structural planes. Keywords calcium-shale, failure form, strength, deformation characteristic, structural planes. Zusammenfassung: basier auf der Anwendung von Problematik des Felsenbauprojektes und Beschaffenheit Felsen unter Beaugnshme auf den Zustand des Druckes von einzeler Welle legt dieser Text dar, wie der Winkel der Schichtstrukturflaeche des schwarzgrau kalziumhaltigen Schieferblocks auf die Zerstoerungs-, Intensitaets- und Deformationseigenschaften einwirkt. Schluesselwoerter: schwarzgrau kalziumhaltigen Schiefer, Zerstoerungseigenschften, Intensitaetseigenschften, Deformationseigenschaften, Flaeche dar Schichtstruktur. Résumé – En fonction de la configuration du massif rocheux sous l’état de la contrainte de pression axiale simple et de la pratique de l’ingénierie de roches, le présent article fait la déscription concernant l’influence de l’inclinaison ? de la couche de structure stratifiée du bloc de schiste calcaire gris noir sur ses caractéristiques de destruction, sa spécificité de résistance ainsi que sa nature de déformation. Mot clés – Schiste calcaire gris noir, Caractéristiques de destruction, Spécificité de résistance, Nature de déformation, Couche de structure stratifiée

Jan 1, 2003

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By B. H. Kim, S. K. Chung

RMR, Rock Mass Rating, is one of the famous rock classifications. However, RMR was proposed empirically and absolutely depends on the experience of engineer. Therefore, engineering verification is needed for RMR system itself. In this study, the factor analysis and the multiple regressions were performed in order to evaluate the validity of rating factor of RMR. Also numerical analysis was carried out using the FLAC based on Taguchi method, a kind of robust designs, in order to examine the support of tunnel corresponding to the revaluated RMR. As the result of the analysis new RMR was proposed with five minimized factors of intact rock strength, RQD, spacing, persistence and roughness of discontinuities. RMR est un des procédés de la classification du roc qui sont généralement utilisés. Mais RMR s'appuie sur l'expérience et se absolument soumet à l'expérience d'ingénieur. Il est donc nécessaire de vér- ifier techniquement sur le système de RMR. Dans cet étude, on met à exécution l'analyse du facteur et la régression multiple pour évaluer la convenance de la cause de classification de RMR. De même, pour évaluer le support du tunnel selon RMR réestimé, on a exécuté l'analyse de la valeur numérique par FLAC qui se base sur la lois de Taguchi, laquelle est une sorte de système du plan robuste. Selon le résultat de la régression multiple, il est proposé de nouvel RMR à partir de l’intensité de roc intact, RQD, l'espacement, la persistance et la rugosité RMR ist eine der weit benutzten klassifikationen fuer die felsenstuecke. Da aber RMR erfahrungs- maessig ist und ueberwiegend von der persoenlichen Erfahrung eines Ingenieurs entschieden ist, ist es mit Sicherheit notwendig, das RMR-system selbst technisch zu ueberpruefen. In diesem studium waren die faktorenanalyse und mehrfachregressionanalyse durchgefuehrt, um die gerechtigkeit der klassifikationenfaktoren von RMR zu bewerten. Ferner war noch eine numerische analyse mit ben- utzung von FLAC aufgrund der Taguchi-methode, eine art technik der robust design, eingefuehrt, um die tunnelstuetze infolge der neubewertung von RMR unterzusuchen. Gemaess der mehrfach regression analyse wurde eine neue RMR, die sich aus 5-eingeschraenkten faktoren wie intact rock strength, RQD, spacing, persistence und roughness von discontinuities zusammensetzen, in vorsch- lag gebracht

Jan 1, 2003

By P J. Fourie, J R. Walklate

Gravity separation techniques have been in use in the mineral sands industry for decades; from the Reichert cone to Wilfley tables, Wright sluices and the Kelsey Jig, all attempting that elusive perfect gravity separation. Just as the gravity separation industry evolved, Richards Bay Minerals also evolved in their use and approach to gravity separation. This paper discusses the history of gravity separation at Richards Bay Minerals and briefly comments on future developments. History Primary Concentration Richards Bay Mineral?s (RBM) first mining concentrator and mineral separation plant commenced operation in 1977 to process ilmenite, rutile and zircon bearing dunal deposits along the northern Natal coast. The orebody contained a greater proportion of non-valuable magnetic heavy mineral in the SG range of 3 to 4 compared to West Australian and Florida USA deposits, making mineral separation more difficult(1). The deposit was mined using two dredges feeding a floating 2000 tph concentrator. Concentrator feed was screened and fed to two four-stage circuits consisting of primary, scavenger, cleaner and recleaner Reichert cones [see Figure 1]. The primary units were fed at a rate of 80 tph and a density of 60% solids by weight.

Jan 1, 2006

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006