Search Documents

By R. J. Gunderman

Cable reel systems for shuttle cars were investigated to determine whether an improved system could be identified. Interviews and mine visits were conducted to better define limitations and problems with present systems. Although simple and relatively inexpensive, present cable reel systems are not fully satisfactory. Several concepts for a different technical configuration were formulated and evaluated. An all ectric system using electronic control and external sensors was recommended for further development.

Jan 1, 1980

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By C. H. Herty

"The work on the physical chemistry of steelmaking, as carried out at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Carnegie Institute of Technology and, the Metallurgical Advisory Board, has covered a series of fundamental studies on the action of oxygen in liquid steel and the application of the findings to open-hearth operation. The staff has varied from 14 to 23 men per year, some of whom have been Bureau of Mines physical chemists and metallurgists, others research engineers of the Metallurgical Advisory Board, and the remainder graduate students employed as research fellows at the Carnegie Institute of Technology. The work on the laboratory studies, and particularly on slag systems, has been in charge of G. R. Fitterer, associate metallurgist, Bureau of Mines, while the plant work has been under the direction of C. F. Christopher, research engineer of the Metallurgical Advisory Board. In all, some 16 physical chemists and metallurgists and 24 research fellows have taken part in the experimental work. Advantage has been taken of the opportunity for cooperation with the University of Pittsburg to have certain phases of this program made the subject of graduate work, particularly the laboratory studies on the deoxidation of steel with manganese-silicon alloys.The general method of studying oxygen has been, first, to determine the solubility of the various oxides in liquid steel. To date the solubility of Fe0 in steel has been determined, over a wide temperature range.3 The straight-line relationship in the plot of solubility versus temperature indicated that under a slag of 100 per cent Fe0 the oxygen was present in the steel as dissolved FeO. A further conclusion drawn from this work was that the solubility of FeO in the metal was proportional at a given temperature to the mol fraction of Fe0 in the slag if the slag contained a large excess of basic constituents. This result was determined from a study of the solubility of Fe0 under slags containing lime and iron oxide in various proportions. These data have been used extensively in determining the saturation of a bath of open-hearth steel under any conditions of slag composition, and results to be given later showed that the solubility curves are consistent with the results obtained in practice."

Dec 1, 1930

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By H. W. Earnest

This report covers the results of a two-phase study to determine the feasibility of underground disposal of retorted oil shale. Two mining methods, chamber and pillar mining and sublevel stoping, were specified for backfilling. Phase I of the study covered the evaluation of hydraulic, mechanical, and pneumatic transport and stowing systems, individually and in various combinations, and the selection of the most feasible methods. Conveyor transport and stowing and a combination conveyor transport and stowing with pneumatic topfilling were selected for detailed study of phase II. Phase II activities included detailed engineering analysis and design of the selected systems, an engineering economic analysis, and a cost comparison with total surface disposal of retorted oil shale. An extensive literature search was conducted and the bibliography is included in the report. Research done under Contract No. J0265052 by the Cleveland-Cliffs Iron Co. Available for reference at Bureau of Mines facilities in Denver, Colo., Twin Cities, Minn., Bruceton and Pittsburgh, Pa., and Spokane, Wash.; U.S. Department of Energy facilities in Carbondale, Ill., and Morgantown, W. Va.; National Mine Health and Safety Academy, Beckley, W. Va.; and National Library of Natural Resources, U.S. Department of the Interior, Washington, D.C. Order ONLY from NTIS:

Jan 1, 1978

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By R. W. Huber

The successful development of a titanium prototype of the 81-mm. mortar base plate for the Army Ordnance Corps is outlined in this report. Information is presented dealing with forming, forging, and machining, welding and assembly techniques, and design changes relative to this prototype. INTRODUCTION The work of the Federal Bureau of Mines in making ductile titanium available2/ has resulted in the establishment of a new industry. Owing to its strategic importance and the combination of low density and high strength, titanium has received considerable attention as a structural metal. Titanium's favorable strength-to-weight ratio is of particular importance to the Army Ordnance for equipment that is transported by airplane or by foot soldiers.

Jan 1, 1956

By N. A. C. Smith

This report on the physical and chemical properties of typical crude oils of southern Louisiana and southern Texas is the seventh in a series of preliminary chapters of a bulletin covering the producing districts of the United States. Preceding reports* may be obtained from the Bureau of Mines on request. The details of the methods used in this survey in collecting samples and making laboratory tests have been discussed in the first three papers. A method of summarizing and interpreting the laboratory data has also been given, but most of the crudes included in the present report differ so radically from those previously reported, that it has been found advantageous to adopt a somewhat different method in making summaries. This method is described in detail later. If any errors or omissions are noted by readers, it is hoped that these will be brought to the attention of the Bureau of Mines, for correction before the appearance of the final bulletin.

Jan 1, 1922

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By R. N. Johnson

This report is a summary of the work performed for the Bureau of Mines to evaluate the feasibility and desirability of a movable in-pit crusher combined with conveyors to substantially reduce or eliminate truck or train haulage in large open-pit non-fuel mineral mines. The report includes an introduction and summary of previous work, an analysis of movable crusher system components, a description of the selected system, a review of possible movable crusher system applications, and finally requirements for future work to bring about the general availability of such systems. It was clear from the program that there is a real need for movable in-pit crushers.

Jan 1, 1982

By M. W. Von Bernewitz

Because the cutting and polishing of stones are parts of the work of the Bureau of Mines in its study of rocks and minerals and in the determination of specimens sent in for identification, it was decided that a circular covering the subject in a general way would be of practical interest. As several books and periodicals give details of the problems in cutting and polishing, this report will not duplicate their information more than necessary. ACKNOWLEDGMENT The manuscript for this circular was read by Oliver Bowles and Forrest Moyer, Building Materials unit, Bureau of Mines, who supplied some of the illustrations; several photographs were taken by Howard Carl, Optical Section, Bureau of Mines. Equipment firms that y contributed information and publishing houses whose books have been abstracted are mentioned in the text.

Jan 1, 1940

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986

By McHenry Mosier

This paper describing mining practice at Morenci, Ariz., is one of a series of articles on mining method, and practice in the various mining districts in the United States. At present (1929) practically all the mineral production in the Morenci district is from the Humboldt mine of the Morenci Branch, Phelps Dodge Corporation. The mining method used is adapted to the type of ore body being exploited; it has been developed by adopting methods used elsewhere and making necessary changes to fit local conditions. Improvements in current practices are still being made.

Jan 1, 1929

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966