Search Documents

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By M. J. Ferrante

A process was investigated for preparing Specification-grade nickel (containing less than 1 percent cobalt) by stripping it electrolytically from a nickel sulfate-boric acid solution and using the stripped electrolyte for the preferential dissolution of nickel from basic carbonates of nickel and cobalt. The basic carbonates were produced at the plant at Nicaro, Cuba, owned by the U.S. Government. Determination of the optimum conditions for deposition of Specification-grade nickel indicated that the upper limit of cobalt concentration was 0.1 gram per liter. The pH, temperature, and concentrations of nickel and boric acid in the electrolyte were not critical. An aluminum cathode and two lead anodes were used at a cathode current density of 1.2 amperes per square decimeter.

Jan 1, 1959

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By F. H. Gunnell, W. C. Dunham

"INTRODUCTION The Treasure Hill mines, situated in Dry Canyon, Ophir mining district, Tooele County, Utah, together with several other properties in the district, examined were examined by Frank L. Wideman, an engineer, the Bureau of Mines, in September 1942.In April 1945, development drilling was started on the Treasure Hill mines, which are operated under lease from the Madison Mines Co. The project was continued in 1946 and terminated in 1947.While the Bureau of Mines project was in progress, the Morgan and Fullion tunnel workings were surveyed by Bureau engineers.ACKNOWKEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative perk, and prepares the final report. The Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. The work here described was under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch."

Jan 1, 1948

By C. A. Mehring

[This paper, which describes the milling practice at the San Guillermo concentrator of the Compania Industrial "M Potosi", S.A., located at Chihuahua, Chihuahua, Mexico, is one of a series of similar papers being prepared by the United States Bureau of Mines. The concentrator treats lead-zinc-silver ore at the rata of 2,300-2,400 tons of dry material daily and produces lead concentrate and zinc concentrate by selective flotation methods. The lead concentrate is smelted at the Chihuahua plant of the American Smelting & Refining Co., and the zinc concentrate is shipped to various European smelters.]

Jan 1, 1933

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra rake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDR listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

This Bureau of Mines report and its companion report (Information Circular 9143) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of mining of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the casts for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mining unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. Coverage for surface mining includes dredging, quarrying, strip mining, and open pit mining. The underground mining includes individual development sections for drifting, raising, shaft sinking, stope development, various mining methods, underground mine haulage, general plant, and underground mine administrative cost. This system can be used for estimating cost data for an undeveloped deposit or for checking or verifying mining costs from a developed deposit, with a minimum amount of background information.

Jan 1, 1987

By Michael L. Clar

The U.S. Bureau of Mines contracted a study to determine the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. All relevant published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines was reviewed and organized into a bibliography. The impacts of mine water with respect to health and safety, production, environment, and costs were assessed. Sources of water inflow into underground mines were described. A summary description and evaluation of techniques that can be used to reduce the amount of water entering underground coal mines was prepared. A review of engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings was conducted. Major emphasis was placed on the identification of the geologic and hydrologic con¬dition of the site, onsite inspection of the methods used and an evaluation of their technical and cost effectiveness.

Jan 1, 1981

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

The Aluminum Company of America announced a temporary reduction of the operating rate at its primary aluminum plant at Palestine, TX where it is developing a new process to produce aluminum metal by electrolysis of aluminum chloride, Output will be reduced by half to about 7,500 tons per year while some improvements are being made on the chemical segment of the plant. The modifications were expected to take 3 to 4 years to complete. Alcan Alumininum Ltd., a major U.S. supplier of aluminum, reported declaration of force majeure on aluminum ingot shipment commitments following the shutdown of its primary aluminum plants at Arvida, Isle Maligne, and Beauharnois, Que. The shutdowns, which began early in June, resulted from management and labor differences.

Jan 1, 1979

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

The following pages discuss the objectives, the background, the scope and a statement of the problem of the study of methods to improve the pillar extraction practices in underground coal mines. 1. OBJECTIVES The objectives of this project were: ? to determine the principal factors contributing to high accident frequency and severity in both conventional and continuous mining operations; ? to compare and evaluate the safety aspects of the "open end" and "split and fender" systems of pillar mining; to establish basic data required to decide what constitutes an adequate pillaring plan that will optimize efficiency, recovery, and safety; ? to determine what measurements or information should be collected, (e.g. roof sag, pillar stress,) to make on-the-spot judgment of impending roof or pillar collapse; ? to make recommendations to improve existing methods or to insure proper techniques are implemented, and ? to suggest areas where additional studies or new research may be of value.

Jan 1, 1975

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000