Search Documents

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By Bruce I. Thomas

As a part of the United States Department of the Interior program for developing natural resources in Alaska, the Bureau of Mines studied the tin-bearing gold-placer deposits in the Tofty area of the Hot Springs district in central Alaska. The principal objective of the Bureau's work was to obtain facts about the extent and character of the placer deposits (including tailing) to indicate the economic or strategic tin-production potential of the Tofty "tin belt." A secondary objective was to determine (if possible) the bedrock Source of the cassiterite and other minerals found in the placer deposits. The placer phase of the work was begun in July 1954 and was continued during the 1955 and 1956 field seasons. Extensions to, and connections between, known placer channels were sought by 82 churn-drill holes. The Bureau drilling did not expand the placer deposits beyond the limits established by drift-mining operations and by previous drilling done by private concerns.

Jan 1, 1957

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 250, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980

By J. W. Thompson

The term "minerals" when employed in a conveyance in the State of West Virginia is understood to include every inorganic substance which can be extracted from the earth for profit, whether it be solid, as rock, fire clay, the various metals and coal, or liquid, such as salt, and other mineral waters and petroleum oil and gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. TERM INCLUDES OIL AND OAS. The term "minerals" used to describe the interest in land granted or reserved bona fide includes petroleum oil and natural gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. INJUNCTION TO PREVENT RElllOVAL. The removal of ore from the premises of another without his consent will be enjoined. Barnes v. Esch (Oregon), 169 Pacific, 512, p. 518. TITLE TO MEXICAN BULLION-JURISDICTION OF FEDERAL COURTS TO DETERMINE. Where bullion within the jurisdiction of the Mexican Government was seized, condemned, and sold for war supplies by the Constitutionalist forces in the revolution acting under authority from Gen. Carranza, claiming to be the provisional President of the Republic of Mexico, a United States district court of Texas, into which State the bullion has been imported from Mexico, has jurisdiction to try and adjudge as to the validity of the title acquired by and through the seizure, appropriation, and sale by the Carranza forces as against an American citizen claiming ownership of such bullion prior to its seizure.

Jan 1, 1919

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Jr. Denton

This U.S. Bureau of Mines report presents the documentation for HEAPREC, a methodology for calculating reclamation performance bonds for cyanide heap leach operations. HEAPREC is a template developed for use with Lotus 1-2-33 release 2.01 or newer software. The report is presented in step-by-step "user's manual" format. Appendices contain detailed background and reference material on performance bonding, cyanide detoxification regulation, cyanide detoxification methods, general mine reclamation procedures, and an example bond calculation.

Jan 1, 1992

By T. E. Howard

The western phosphate field, comprising parts of Idaho, Montana, Wyoming, and Utah, contains one of the world's largest known reserves of phosphate rock. Although phosphate-rock deposits of good-grade have been known since before the turn of the century and production has been recorded since 1906, real development of this important field did not begin until immediately after World War II. Since then fertilizer-manufacturing facilities using western phosphate rock have been expanded, and three electric-furnace plants for producing elemental phosphorus have been installed, resulting in a rise in mine production from 323,955 long tons2/ in 1945 to 1,653,916 long tons3/ in 1953. Interest in the field is increasing, and it is reasonable to expect that the western phosphate industry will continue to expand. Before 1945 all western production was from underground mines. In that year the first strip mine in the field was started near Montpelier, Idaho,~ and in sub-sequent years a number of other open-pit mines were opened in southeast Idaho and western Wyoming. At present the major part of the production comes from surface mines. Underground mining has continued, and new underground mines have been opened in the field, but recent exploration by operating companies has been aimed primarily at developing additional deposits suitable for low-cost surface mining. Preliminary reserve estimates by the Federal Geological Survey5/ indicate that only a very small part of the total resource may be recovered by surface methods and that the industry eventually must depend largely on underground mining. Because one function of the Bureau of Mines is promoting the conservation and development of the Nation's mineral resources, it is appropriate that research be conducted to develop low-cost maximum-recovery underground mining methods applicable to western phosphate-rock deposits.

Jan 1, 1956

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By R. B. Crookston

Oil shales differ from coals in that they contain less carbonaceous material, convertible to volatile hydrocarbons, and more inorganic rock. In all pre-commercial oil shale development, involving extensive full scale mining operations, there have been no explosions. However, large scale mine tests with oil shale dusts by the Bureau of fines showed that propagating explosions could be induced under certain circumstances. Laboratory tests were conducted on a broad spectrum of oil shale dusts to define chemical properties and to seek correlations with subsequently determined fire and explosivity properties. These latter properties, indicative of safety hazards, increased as the Fischer assay oil yield of the dusts increased and as particle size decreased. Laboratory data were used to relate fire and explosivity properties of oil shales to those of coals and other carbonaceous materials and to assist in the identification and evaluation of potential hazardous situations which may be encountered in oil shale mining and processing.

Jan 1, 1978

By Eugene O. Binyon

"Belt and shaker conveyors, used singly or as combined units, have for many years been an integral part of many coal-mine haulage systems. The belt conveyor has also been used extensively as a main haulage unit in open-pit iron-ore mines of the Lake Superior district, particularly on the Mesabi Range. Few underground metal mines, however, either in the ferrous or non-ferrous branches of the mining industry, use the conveyors exclusively or even extensively for underground haulage. At present, only five iron-ore mines in the entire Lake Superior district have belt- or shaker-conveyor installations of any significant size. Of these mines, three are in the Crystal Falls-Iron River district of Michigan on the Menominee Range, one is on the Marquette Range near Ishpeming, Mich., and one is on the Mesabi Range near Keewatin, Minn.Results of the studies of tackless haulage in the Lake Superior district will not permit the establishment of any formula to prove or disprove the advantages of belt or shaker systems at all underground mines. The studies do show that trackless haulage can be used to advantage where the proper conditions exist. Advantages are particularly apparent when development can be planned sufficiently in advance of exploitation to permit installation of belts or shakers as part of the development program and where the systems are extended to include haulage in stopes as well as main entries.During the winter of 1947-48, the Bureau undertook a study of all of the underground ore conveying systems known to be in operation in the Lake Superior district for the purpose of making available to the entire mining industry the technologic data developed in the area. Because conditions that led to the installation of the belt and shaker conveying systems were often a function of the character of the deposit or the method of mining, a brief description of those conditions is included in this report.After a preliminary investigation into the extent to which trackless conveyors were employed in the district, it was found that a detailed study at five bites would result in fair appraisal of that method of haulage in the underground iron-ore mines.Each of the five significant installations is described separately in this report. In one instance, however, company policy does not permit identification of the mine wherein the conveying is done. In that instance the operation is designated as mine ""A"".Unless otherwise specified, all tonnage figures quoted herein are gross.The cooperation of officials of all of the companies operating underground mines in the Lake Superior district permitted successful completion of preliminary studies of mining practices and conveying systems.Special acknowledgment is made to R. D. Satterley, general superintendent, and to operating staffs of the Sherwood and Morris mines of the Inland Steel Co. The assistance given by W. D. Whitman, assistant superintendent, and Douglas Tippett, mine captain at the Morris mine, and P. D. Pearson, superintendent, R. O. Marsten, engineer, and W. Johnson, mine captain, at the Sherwood mine, is acknowledged."

Oct 1, 1949

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By E. S. Shedd

Amenability studies were conducted by the Federal Bureau of Mines on an electrooxidation technique for the extraction of mercury from cinnabar ores, particularly those that are too low in grade to be furnaced or retorted economically. Oxidation was accomplished by electrolysis of the ore while slurried with brine. Mercury was dissolved through the formation of the soluble tetrachloro mercury complex, HgC142-. Mercury extractions ranged from 90 to 98 percent in 4 to 6 hours of processing time when tests were made on eight different types of cinnabar ores containing from 0.7 to 18 pounds mercury per ton ore. Salt concentration was varied from 4 to 10 weight-percent depending on whether Pb02 anodes and iron cathodes were used or whether graphite was used for both electrodes. Power consumption ranged from 17 to 64 kilowatt-hours per ton of ore treated. Ninety-nine percent of the mercury was recovered from pregnant solutions by precipitation on an active metal such as zinc, followed by distillation of the resulting amalgam at 600° C.

Jan 1, 1975