Search Documents

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018

By Dr. Bronwynne Victor, Quentin Steyl, D. Scott Scovira

Bulk emulsions and emulsion blends may be formulated with a single salt, dual salts, or multiple salts. Blasting professionals familiar with single salt ammonium nitrate emulsion products may be less acquainted with dual and multiple salt emulsion products that may include calcium nitrate, sodium nitrate, and urea in their formulations.

Feb 1, 2020

By Remi Proulx, Ruilin Yang

The effectiveness of presplit in soft or fractured ground is hard to visualize or quantify. There have been many attempts by the blasting community to measure and quantify the effectiveness of presplit blasts. Various methods have been adapted by different researchers, and the results are debatable.

Jan 1, 2019

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023

By Denise Clarke

Homeland Security Qualifications (HSQ) personnel were instrumental in developing the UK’s suite of Explosive Substances and Articles (ESA) National Occupational Standards (NOS) (also known as "competences") on behalf of the Standards Setting Body for Explosives, Munitions and Search Occupations (SSB for EMSO).

Jan 1, 2013

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By S. Behera, K. Dey

This paper presents a methodology for finite element (FE) modelling to analyse the total deformation of rockmass under blast-load, with a focus on predicting backbreak that may occur during surface blasting operations. Backbreak can result from improper use of explosive energy, leading to damage beyond the excavation zone and jeopardizing operational safety and productivity. The paper highlights the impacts of backbreak on bench stability, excavator operation, drilling operation, flyrock generation, and improper fragmentation and boulder formation in surface blasting. However, prior estimation of extent of rock breakage zone can provide an idea to formulate the blast design to control the backbreak. While vibration-based prediction models are commonly used to estimate backbreak, they require physical blasting experimentation. To overcome this limitation, the paper describes the development of a FE model using ANSYS Explicit dynamics, which simulates rock blasting and calculates the total deformation of the rockmass. The rockmass deformation is modelled using Drucker-Prager (D-P) strength model with the Jones-Wilkins-Lee (JWL) equation of state for the explosives. The accuracy of the FE model is evaluated through physical experiments, and the results are compared with the vibration models. The FE model demonstrates close proximity to physical observations as well as vibration model result in predicting backbreak, thereby offering a promising alternative to vibration-based prediction models. The primary objective of the study is to predict the response of the insitu rockmass to explosive blast loading and determine the effective rock breakage zone.

Jan 1, 2024

By Jack Eloranta

Proper selection of stemming has a profound effect on blast performance. This paper describes several methods of evaluating stemming performance in 16-inch blastholes. Tests are done on stemming ranging in size from nominal 1/4" crushed rock up to railroad ballast size rock (2 1/2" > diameter < 3/4"). Concrete plugs (both pre-cast and poured) are evaluated as well as air decking.

Jan 1, 1994

By Corry Goumans

Photos 1 - 4 – Chris Elliott is a rock slope supervisor on a construction project east of Seattle, Washington. His job is to look after a “two man” scaling crew working on the rock bluffs some 300 feet in height along the I-90 interstate just east of the town Hyak. The Washington State Rock Engineers noticed a very large mass of unstable rock along the upper rock face and asked us to take it out. Chris is loading explosives in 1½" ” holes that are 8 to 10 feet deep by 40 feet long with 1¼” x 8” power primer on the unstable rock mass that is about 300 feet above the new road construction. I-90 runs east and west longside the new construction note the containment fence and the ship containers along the highway for protection and Lake Keechelus in the background.

Jan 1, 2014

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By John Brennan

Necessity, they say, is the mother of invention. Certainly that sentiment held true during the early stages of explosive engineering. While seaside forts were concerned over static ignition of their black powder caches in the 14th century1, the mining industry in the 1800s were plagued by accidents surrounding the ignition methods for their black powder blasts.

Jan 1, 2011

By Dyno Nobel

Impact of Enhanced Security on Operations Budgeting - What is the “value” I receive for enhanced security? Is there a “return” for the money I spend? Regulatory driven Economic driven

Jan 1, 2006

By Claude Cunningham

Blasthole pressure is the starting point for many blast design calculations, but the way in which it is usually derived, from measured detonation velocity, indicates that more thought is needed as to its true meaning and implication. The general impression is given that the energy in the hole is defined by VoD, but rarely is this the case. VoD is defined by the energy released in the Detonation Driving Zone between the shock front and the Sonic (or 'CJ') surface, and for commercial explosives it is normal for reaction not to be complete within this zone. Reaction and energy delivery continues behind it, not reflected by VoD. Thus it would be more appropriate to use the theoretical VoD, not the measured VoD, to derive the starting pressure, since this would reflect the energy input of full reaction. In decoupled situations, the derivation of pressure at the blasthole wall using a polynomial decay concept is also of debatable value, and an alternative is offered.

Jan 1, 2006

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By L. O. Souza, J. F. Gewher, M. P. Scussiatto, C. S. Mendonca, R. A. McClure, B. T. Kuckartz, J. Kloeckner

Blasting is the most effective and economical tool available to fragment and move rock for most applications. If properly executed, it can improve down-stream operations such as loading, hauling and crushing. It is not possible, however, to have full control over the energy released by the explosives when a poorly designed blast pattern is used. A poorly designed blast can produce serious damage to equipment and create a potentially hazardous condition to people. Advanced mining technology has been developed to address these potential hazards and optimize the blast pattern. This profiling technology can assist with blast planning and provide quick, precise data about the condition of the rock structure to be blasted. The 3G BlastMetrix system presented here uses three-dimensional (3D) stereo photogrammetry to model the rock mass in a fast, practical and safe manner. Through the image overlapping method, a 3D model is created with thousands of points that provide a significant amount of data regarding geology, geometry and topography conditions. The blasting plan can then be made in a way to optimize the rock fragmentation and avoid areas that could create flyrock. This paper is a case study concerning usage of stereo photogrammic surveying and borehole survey systems in a blasting operation at the Brazilian Quarry, Incopel. One 3D image of a drilled bench was generated using photogrammetry survey technology and the borehole survey data collected using the rodded Boretrak borehole survey system. Utilizing the minimum burden profile reports, explosive loading could be done accurately, resulting in an optimized blast with good heave and fragmentation as well as increased safety.

Jan 1, 2013

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

This case history refers to the detonation of the two largest chemical explosions on the Australian continent. An important element of feasibility studies and construction guidance included prediction of fragmentation results and ground vibration effects for the detonation of two very large "coyote" blasts, consisting of mined tunnels filled with explosives. The larger of the two blasts contained nearly 1 1/4 million pounds of explosives detonated instantaneously. The explosives were placed in specially designed tunnels under a quartzite mountain for the purpose of generating rock fill for the main dam on the project.

Jan 1, 1995

By Robert S. Mayo

Tunneling, for transportation, began in France with the Milpass Tunnel on the Lanquedoc Canal in 1680. Of course, the ancient miners had been driving tunnels in search of minerals since the dawn of history but this Milpas Tunnel was the first tunnel exclusively for transportation. In England in 1760, the Duke of Bridgewater opened a canal from his coal mines to Manchester, 10 1/2 miles away. At the mine, he drove a tunnel into the mountain so that the miners could shovel the coal directly into canal boats. James Brindley, an untutored genius, was his engineer and this whole transportation system was an instant success and very profitable through the years. Within a dozen years the Duke, again with James Brindley, opened up the Grand Trunk Canal, 139 miles in length with five tunnels. There was one major tunnel on this system, the First Harecastle Tunnel, 1 1/2 miles in length. But this tunnel was too small. It was only large enough for one 7-ft wide boat which had to be "legged" through by boatmen laying on their backs. By 1824 a second tunnel was driven parallel to the first one, but it had a towpath through it for horse haulage. This was the beginning of the " Industrial Age" and tunnels became a very important part of that era.

Jan 1, 1979