Search Documents

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

By Sang Ho Cho, Masaji Kato, Masaaki Yamamoto, Masaaki Nishi, Katsuhiko Kaneko

This paper presents a numerical simulation method to predict rock fragmentation and to verify a fracture mechanism by bench blasting. The rock fragmentation, which has been used as a means of the index to estimate the effect of bench blasting, affects the expenses for loading, conveyance and crushing of blasting muck piles. The developed numerical simulation method is based on the finite element method and fracture mechanics and includes the re-meshing procedure to express the fracture process of the rock mass. This paper discusses a procedure for a determination of size distributions of the results, which were calculated by numerical simulation, including the tines.

Jan 1, 2002

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By John Dean Smith

"In many operations the two most overlooked aspects in the drilling and blasting process is theblast optimization and explosive selection. Often times we find a blast design that seems to work andproduce acceptable results and will use this cut afier cut, even years. When in reality one should never become complacent and should be constantly looking for ways to improve the drilling and blasting operation."

Jan 1, 1995

By Rolf Schillinger

Blasting activities on the surface or underground necessarily involve the most sensitive aspect of environment remediation, human response or annoyance. Such effects are unavoidably characteristic of those activities. For this reason, blasting activities are governed by law and official regulations under surveillance of authorities, where companies and explosives engineers have to proceed within proper limits. Subject of the paper is a practical way of handling some necessary vibration standards being focused on blasting activities. The paper is based on the German Standard DIN 4150, Part 1 - 3, “Vibration in buildings”, Part 1: “Prediction of vibration parameters”, June 2001, Part 2: “Effects on persons in buildings”, June 1999 and Part 3: “Effects on structures”, February 1999.

Jan 1, 2006

By Lyle Dennis

Emphasis on increased production while maintaining rigid quality standards has necessitated a change in blasting technology at Dacotah Cement's limestone and gypsum quarries. The following three methods implemented during the past three years have yielded an increase in production through improved fragmentation.

Jan 1, 1996

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By C V. B Cunningham

The assessment of blasting results under production conditions is extremely difficult. As a result, it can take months or years to establish objective and valid estimates of explosive performance in achieving rockbreaking goals. This fundamental problem often results in decisions related to the manufacture, marketing, purchase and use of explosives being largely swayed by calculated energies from detonation codes. However, these codes are by no means standardised. Different energies are given by different codes because these employ varying combinations of fundamental science and empiricism. After a basic review of code operation, important guidelines to dependability are given with reference to ICI’S state-of-the-art codes IDEX and CPEX. Distinctions are drawn between Ideal, Non-Ideal and Blasting Codes. Concepts of explosive energy are discussed in brief.

Jan 1, 1991

By Roberto Folchi, Hans Wallin

Having so many norms and technical content of legislation to deal with is a problem that an explo-sives engineer has to face, especially when working at an international level. Each country has its own norms and legislation, sometimes even each other region or state, as if the physics of explo-sions, rock, concrete, and masonry characteristics would change across the borders. Both norms and laws are frequently out of date, being mainly developed at the beginning of the previous century and adjusted, piece by piece, to a technical and political context that is constantly changing, with adjustment being frequently adopted in a hurry, due to a problem arising such as that of internation-al terrorism. Sometime also, norms are not harmonized with those they intend to amend, so required explanations and new adjustments lead to a vicious circle that increases confusion, complexity and depresses the explosive industry.

Jan 1, 2015

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Benoît Pinier, Jason Furtney, Gustavo Sampaio Lopes, Jorge Valencia, Johan Hawinkel

This paper describes a numerical modeling study on the effect of airdecking on vibrations, fragmentation, and movement in mining-related rock blasting. Practice has shown that air gaps reduce blast vibrations and damage while maintaining the required fragmentation and movement, yielding similar blast outcomes with less explosive mass per hole. Given that the premise of “replacing explosives with air” for better blast results is counterintuitive, this paper aims to shed light on the physical mechanisms and processes occurring in a blast with airdecks. It is hypothesized that airdecks are effective and beneficial because they load the rock at pressures lower than what is required to crush the rock. In the airdeck, the explosive gasses directly fracture rock and avoid energy loss due to crushing. In essence, the airgap allows similar outcomes in fragmentation and throw with less total explosive product, as the lower pressure gasses in the airdeck are still effective at breaking and moving the rock. This is distinct from only having less explosive and more stemming, as the stemming reduces the pressure more than an airdeck at the same position. This study uses the blastFoam software (for modeling of single and multiphase flows) to accurately calculate the pressure history throughout a blasthole and air gap. The pressure and gas loading are coupled to numerical models of vibration, fragmentation, and blast movement. Using this modeling technique, a suite of blast scenarios for typical configurations in a range of commodities is assessed with and without airdecks. Rock blasting practitioners have a responsibility to protect communities, infrastructure, and heritage — demystifying airdecks through a better understanding of the physics provides another tool in the blasting engineering toolkit to serve this goal.

Jan 21, 2025

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By William Nicoll

Those who use electric detonators in firing blasts will be interested in a new electrical testing instrument known as the ‘Blasters’ Friend’, recently devised by the New York Blasting Supply Co. of New York. Owing to the necessarily delicate construction of the platinum wire bridge in the shell of a detonator, it frequently happens that it becomes broken or disconnected; thus destroying the circuit and rendering the detonator worthless. In many cases, misfires and premature explosions are caused by defective detonators. Heretofore, to detect the deficiencies of a detonator before using has been an impossibility, owing to the absence of a testing instrument adapted to the purpose.

Jan 1, 2010

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005