Search Documents

By Michael S. Wieland, Thomas C. Ruhe

Delay blasting in underground coal results in shock waves traveling through the coal that can damage delay charges remaining in the blast pattern. Undetonated explosives which are dynamically desensitized or react sympathetically from shock wave impact ruin blast results. Such malfunctions, sometimes manifest as misfires, more frequently are covert weak detonations, and result in poor coal breakage and fumes with above normal toxicity. To reduce these mining hazards and resolve charge performance problems, the Bureau of Mines has developed and tested forty prototype rugged explosives in the laboratory. Rugged explosives work properly under difficult circumstances because they not only retain their shock initiation sensitivity but also are resistant to shock damage. This research investigation resulted in one candidate emulsion explosive, formulation #37, which passed all the permissibility tests required by MSHA approval regulations. However, approval was not granted because it reached shelf-life (would not shoot properly) seven months into testing. For research purposes, the remaining tests were conducted with a second batch of formulation #37. This paper discusses the prototype rugged explosive composition and permissibility test results. Where possible, for reference purposes, comparisons are made to a commercial product that has been approved. Further research work is required to overcome the noted deficiency of short shelf-life.

Jan 1, 1992

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

In the context of its studies for the french ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blasting vibrations.

Jan 1, 1996

By Francis O. Otuonye

The results of an ongoing study to determine the response of full contact rock bolts to shock waves due to blasting are presented. A time domain systems modeling and analysis technique was used to identify the axial and bending response of the bolt when explosives charges are detonated at close-in distances.

Jan 1, 1993

By Doug Hoy

The scope of the Cliff Avenue Reconstruction Project in Sioux Falls, South Dakota was to widen a two lane highway to five lanes, along with removing and reconstructing both above and below ground utilities located along the project limits. The objective of this paper is to present the blasting techniques used in the rock excavation phase of the Cliff Avenue Reconstruction Project.

Jan 1, 1992

By Yuji: Wada Ogata, Kunihisa Katsuyama

It is well known that a compressed stress wave reflects at the free face, it propagates to the backward as a tensile stress wave, and cracks grow when the tensile stress becomes the dynamic tensile strength. The behavior of these cracks has been discussed through the observation of the dynamic photoelastic high speed photography.

Jan 1, 1993

By Syed M. Tariq, Paul N. Worsey

Pre-splitting is now widely used to minimize overbreak and to protect final surface rock excavation profiles in large scale civil construction projects, open pit mining and quarrying. Jointing has been shown to affect the success of pre-splitting and the smoothness and integrity of the resulting rock face. Many facets of jointing have been investigated in detail, including the inclination of joints with respect to the desired pre-split plane, the effects of various filling materials, etc. However, the effects of joint frequency and spatial positioning has been paid little attention. The paper addresses this issue.

Jan 1, 1995

By Young-Dong Cho, Han-uk Lim, Bok-Ki Park, Sang-Eun Lee

Many methods and techniques have been developed to reduce ground vibrations. Some of them are an adoption of electric millisecond detonators with a sequential blasting machine and an improvement of initiating system with an adequate number of delay intevals.

Jan 1, 1995

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978

By Ignacio Humeres Valdivia, Alejandro Ferrada Vergara

In the latest years, the use of innovative blasting techniques has become more frequent in mines all over the world. Such techniques allow the miner to be more aggressive in the distribution of explosive energy into the rock mass, e.g., stretching blasting patterns to improve fragmentation. Considering the different rock mass conditions and more energetic blasting designs, misfired shot events have occurred. After cause investigation, initiators have shown evidences of deformation by impact and/or loaded boreholes have resulted in emulsion desensitization, both presumably affected by dynamic pressure.

Jan 1, 2015

By W. J. Birch, R. Farnfield, G. D. Rangel-Sharp

It is widely recognised that complaints from members of the public relating to blasting operations are related to both ground vibration and air overpressure. It is also known that a complaint is more likely to be generated if the person is inside of a structure at the time of the blast. Reports relating to such complaints often refer to ‘noise’ inside the structure with terms like ‘rattling’ commonly being employed. Such acoustic response is widely perceived within the blasting industry to be directly related to high levels of air overpressure although there appears to have been very little research carried out specifically related to this effect.

Jan 1, 2007

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By Brent Blanchard

The use of explosives to safely fell structures can be traced back over 300 years. Since then, dozens of chemists, inventors, blasters and demolition experts worldwide have played prominent roles in the evolution of what has become the modern-day explosive demolition industry. In America, one of the earliest applications of explosive demolition occurred in response to the great fires of San Francisco, where homes and businesses were blasted with gunpowder in a desperate attempt to create firewalls. Later in the 19th century, inventions such as nitroglycerine, dynamite and blasting caps made structural blasting a safe, efficient alternative to conventional demolition methods. The 20th century brought the first experiments in shaped charge technology, and this, combined with developments in portable seismology and non-electric delay systems, allowed an ever-expanding variety of structures to be explosively felled by demolition experts throughout the country. The 1950s and .60s brought a new wave of commercial structural-blasting entrepreneurs (several of whom are still active today), and their efforts towards improving adjacent-structure protection and public relations beget the felling of large commercial buildings in dense urban environments. By the late 1980s, publicity-driven motives were gaining greater influence in the decision to .implode. various structures, and the transformation of blasting operations into promotional spectator events played a role in several injuries and fatalities. Since that time, however, a renewed sense of responsibility practiced by most blasting firms and project officials has resulted in the safe, successful completion of hundreds of recent endeavors. In sum, what appears today as an efficient, economical - and visually spectacular - way to demolish structures has its roots in developments of the past several centuries

Jan 1, 2002

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By John T. Day, Lex L. Udy, Mark L. Thomas

When we consider that the purpose of blasting is to fragment rock or ore so it can be subsequently handled and processed, we can see that the cost of blasting, in reality, affects all downstream steps of the mining (and in some cases) production processes. The productivity of all subsequent operations is influenced by the degree of fragmentation of the primary blast.

Jan 1, 1987