Search Documents

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates."

Jan 1, 2003

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates.INTRODUCTIONThe process of leaching is widely used in hydrometallurgy to selectively recover a metal of interest from an ore or a concentrate. Leaching and by extension hydrometallurgy is well established in the recovery of copper (copper heap leach ? SX-EW), nickel (Moa Bay and Caron process), zinc (roast ? leach ? electrowin and zinc pressure leach), gold (cyanidation) and uranium (acid sulfate leach). Of course this success extends to many of the metals found in nature. Recently, the importance of hydrometallurgy appears to be increasing with hydrometallurgy viewed as an attractive alternative to both traditional mineral processing and conventional smelting/converting/refining. This increasing interest has led to intensive study and increasing application. Selected developments include:Copper ? the Mt. Gordon process and new concentrate processes such as INTEC, Activox, CESL, Dynatec, Total Pressure Oxidation, MIM Albion, BioCop, and the AAC/UBC Process.Nickel ? Voisey Bay process for hydrometallurgical treatment of Voisey Bay concentrate, HPAL processing of laterites at Murrin Murrin, Bulong and Cawse, atmospheric leaching of laterites, heap bioleaching of nickel sulfides by Titan Resources (Australia).Zinc ? establishment of zinc leach, solvent extraction and electrowinning technology for treatment of the Skorpion deposit in Namibia, new developments in atmospheric and pressure leaching, the Hydrozinc process.Gold ? development of a number of thiosulfate leaching processes for recovery of gold from refractory carbonaceous ores or concentrates."

Jan 1, 2003

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Graeme J. Jameson

In conventional flotation machines, the recovery is strongly related to particle size. As particle size increases, the recovery also increases, reaching a maximum in the range 20 to 120µm. Beyond this range however, the recovery declines quite quickly. The reason for the decline in recovery observed with coarse particles can be traced to the effect of turbulence. Bubbles trapped in turbulent eddies rotate rapidly, and when the centrifugal force on a particle exceeds the retaining forces due to surface tension, the particle detaches. Since the centrifugal force varies as the cube of the diameter of the particle, and the attachment force varies simply as the diameter, being proportional to the length of the contact line, it is clear that detachment forces will predominate as the particle size increases. The corollary is that the recovery of coarse particles can be improved if the level of the turbulence in the cell can be reduced to a minimum. In this paper, a new type of flotation machine will be described, in which the particles to be floated are suspended in a fluidized bed. An up flow of fluidizing water is provided, by recycling liquid from the top of the cell. The recycle stream is aerated in a high-energy device that disperses the air into fine bubbles that capture the fines and ultrafines. Results are presented for several minerals and coarse coal. Keyword: fluidized bed flotation

Sep 1, 2012

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By P. Condori

In spite of the importance of the slurry transport and discharge in autogenous and semiautogen-ous (AG/SAG) mills, it is evident that a more comprehensive and useful model is still required. Semi-empirical models used up to now have many limitations and cannot be used beyond the ranges in which they were developed. The breakage of particles as they are transported along a mill com-plicates the experimental analysis and the modelling of the transport process within the mill. The interaction of the grate discharge and the pulp lifters, with the added issue of backflow from the pulp chamber into the mill, makes the discharge modelling process difficult. In order to overcome these difficulties, a mechanistic approach has been applied. The general transport and discharge model was subdivided into four independent models: Flow through the charge, flow through the grate, flow in the pulp lifter, and flow-back. This paper gives an overall description of the modelling approach and discusses in particular the modelling of transport of fluids through the charge. In order to evaluate and calibrate the model, experimental work was carried out. To evaluate the gradient pressure under different conditions of charge packing and flow rate, a specialised experimental rig with a highly sensitive pressure gauge was used. Preliminary results identify the differences of the charge and grate on the restriction of flow. The existence of a dynamic voidage in our particular system was more evident and as a result, a semi-empirical correlation for the voidage was developed. In general, results show that the me-chanistic model derived from Ergun?s equation for flow through a packed bed can be satisfactorily adapted.

Jan 1, 2014

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By Paula Olea, Gonzalo Montes-Atenas

Froth flotation operation is a large tonnage process aiming at selectively separate economically valuable minerals from gangue material. The wellbeing of an industrial froth flotation operation has been historically assessed and understood in terms of many variables known to somehow affect the process performance. Among these variables, air dispersion have been pointed out as key to secure the correct transport of hydrophobic particles to the froth phase and, then, to the concentrate. One of the classic parameters assessed when evaluating the air dispersion in flotation tanks is the superficial gas velocity. Many reports have focused on studying the superficial air velocity profiles across the pulp phase and theories have been based on the fact that the measurements should be performed in the so called "quiescent zone", which is a volumetric region inside a flotation cell of difficult determination. The hypothesis behind this research work is that the reporting of particles to the concentrate would provide a better correlation with the effective air flowrate pattern created in the froth phase. The aim of this study, as a first step towards developing a flotation model fully froth phase-based, is to estimate the effective surface area used in a flotation cell derived from results obtained with a specific setup at laboratory scale. The methodology considers running a thin lateral flotation cell cut at different superficial air velocities, with and without particles. It was found a non-linear correlation between the superficial air flow rate and the characteristic distance between the vertical wall next to the cell lip and the cut point where the foam or froth flowrate almost stops contributing marginally to the overall amount of solid particles transferred to the concentrate. The presence of hydrophobic particles reduced the mobility of the froth phase reducing the characteristic distance.

Jan 1, 2014

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Kazimierz Trybalski

"Simulation methods have a big potential in the studies and analyses of complex technological processes and schemes. The simulation method used jointly with flow diagrams and related transmittance models allows describing and analysing dynamic characteristics.The paper presents results of simulation analysis of dynamic characteristics of ore dressing system, called closed circuit mill-classifier-mill. Such systems are widely used in ore processing plants. The system was analysed as a typical system with material feedback, to establish its dynamic characteristics.Flow diagram conforming to the technological scheme is presented in a figure. Transmittances shown in the scheme are defined as follows:GMP - transmittance of rod mill,GP, KZ, GW, KZ - transmittances of overflow and underflow streams of spiral classifier, respectively,GMK - transmittance of ball mill,GT - transmittance of underflow stream from classifier to ball mill,GU, MP, GU, MK - fraction transmittance of outflow streams of rod and ball mill, respectively, summed up at classifier input.Taking into account, in base of carried out analysis the transmittance forms of individual system elements. The calculations are based on numeral forms of transmittances of individual blocks, defined through industrial experimentation.Step input function to rod mill was assumed to be a step of mass ore flow rate to the mill. Responses are defined as product densities.This figure demonstrates the way of input signal transmission by consecutive elements of the system and shape of these elements' responses. It can be noticed that step signal undergoes gradual change from the stream of the first order to those of higher and higher orders as a distance from process leading edge increases. Simultaneously, the impulse signal is subject to systematic smoothing and decay. From the technological point of view, the most important is response stream in point 5 (on the above figure) that characterises classifier overflow, which is a final product of this system."

Jan 1, 2003

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By V. F. Bannikov, A. P. Kozlov

"The purpose of this study was to develop a theoretical and technology framework for designing new combined technologies for processing tailings containing non-ferrous and noble metals using dry separation. The main goals of the study were: identifying the distribution patterns of valuable components in various fractions in dry separation processes; examining the patterns identified for different types of non-ferrous and noble metal tailings; developing a theoretical and technology foundation for the development of innovative technologies for the efficient processing of tailings with minimal process water consumption. To examine the possibility of efficient recovery of valuable components from refractory tailings using dry separation, an experimental laboratory unit was designed and built, composed of novel or modified lab equipment: plasma unit for increasing the magnetic susceptibility of Fe - containing minerals; magnetic separator supporting isodynamic and polygradient fields; pneumatic separator for the dry separation of finely dispersed mineral mixtures; dielectric separator using the resonant frequency of the electric field. The laboratory unit supports various modifications and combinations of the lab equipment. The experimental studies led to the development of a unified process scheme for lab tests of mature and non-ferrous smelter tailings using dry separation methods.INTRODUCTION The huge amount of waste from mining and processing of mineral resources Russia inherited from the extensive use of mineral resources in the Soviet Union and amount of waste continue to grow. Often the content of valuable non - ferrous, rare and noble metals in waste exceeds the balance contents in natural ores of the developed deposits. The availability of a rich scientific reserve for the creation highly effective innovative technologies for waste processing determines the necessity of the acceleration in the resolution of problems of the complex assessment, capitalization and involvement in the processing of technogenic resources in Russia (Chanturiya and Kozlov, 2014.)."

Jan 1, 2018

By H. Hamza, M. R. MacIver, M. Pawlik, L. Malin

"Size and shape are important properties of aggregates formed in engineering processes and natural systems. Measurement of aggregate size or shape is a challenge when the solids concentration is beyond the gel point, ?? > ??g, when the aggregates are in contact and it is difficult to distinguish or segment individual particles in the network. This paper describes the use of a micro-computed tomography (micro-CT) method for the calculation of the aggregate volume fraction, ??, and a characteristic aggregate length, ??a, based on a 3D chord length measurement algorithm. These parameters can be used to quantify changes in aggregate and pore size during a compressive yield stress test to help understand the impact of flocculation and network structure on dewatering. INTRODUCTION In a thickener, flocculation is often used as a pre-treatment step and the final solids content of the underflow depends on the network strength and permeability of the bed formed by settled aggregates (Usher, Spehar, and Scales 2009). This paper describes the measurement and analysis of micro-computed tomography (micro-CT) of flocculated mineral sediments to obtain a characteristic length, ??a, of the aggregate and pore phases during a staged compressive yield stress experiment. This parameter may be used as an indicator of changes in aggregate and pore size to quantify material behaviour in solid-liquid separation processes that depend on self-weight compression or applied pressure. This analysis was carried out to help understand the effect of flocculation on aggregate structure and the thickening process as part of a broader research on the improved solid liquid separation of tailings produced in the oil sands industry.Aggregate properties The solids phase of an aggregated or flocculated suspension will eventually settle – if left undisturbed – under the influence of gravity. As settling of a flocculated suspension continues, the solids volume concentration, ??, may increase to the gel point or gelation threshold (Landman and White 1994), ??g, above which the aggregates form a network of touching particles, or space-filling structure (Kranenburg 1994). In the sediment bed, the aggregates are surrounded by fluid and occupy a partial volume fraction, ??, according to"

Jan 1, 2018

By Jiongtian Liu, Jianjun Wu, Yongzhou Wan, Li Feng

"Mechanical Thermal Expression (MTE) is a developing non-evaporative lignite dewatering technology. It has been shown to effectively dewater high moisture content in low rank coals via the application of mechanical force and thermal energy at elevated temperatures. In this paper, the dewatering behavior of Yunnan Xiaolongtang lignite during the MTE-process was studied. Furthermore, how variations in temperature and pressure during the MTE process affect the surface oxygen functional groups and pore structure were also discussed using Fourier transform infrared spectrometer (FTIR) and mercury intrusion porosimetry (MIP). Increases in MTE temperature and pressure resulted in significant reductions in residual moisture content and moisture holding capacity, along with the increase of fixed carbon content and reductions of other elements content, especially oxygen content, which have been largely attributed to the destruction of the surface oxygen functional groups and porosity in lignite. The optimized technology conditions are temperature 150~220°C and pressure 7~10MPa. The residual moisture content of the lignite treated by MTE under the conditions of 200°C and 10MPa is decreased to 8%, while the dewatering rate exceeds 76 % and the calorific value approaches 22 MJ/kg. The experimental results offer a deeper understanding of the influence of process parameters on the lignite stuctures and properties. The reduction in residual moisture content, surface oxygen functional groups and pore volume under increasingly severe MTE conditions are suggestive of the structure changes that accompany increased coalification (rank) within the lignitic range."

Jan 1, 2014

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003