Search Documents

By C. Dorfling, W. A. Rossouw

"Hydrometallurgical processes used for metal recovery from waste printed circuit boards (PCBs) typically involve dismantling, shredding and physical separation prior to successive leaching stages for selective dissolution of different metals. The principles of the physical separation units are well understood, but valuable metal losses of more than 30 % can be incurred during these processing steps. The impact of the physical separation units’ performance on downstream leaching operations have not been defined; this prevents the development of a well-integrated process. The objective of this project was to determine to what extent the base metal leaching behavior depends on the physical separation pre-treatment. PCBs were shredded to 100 % passing 2 mm before physical separation by dense medium separation (DMS) as well as magnetic separation. Batch leaching tests using various concentrations of sulfuric acid were conducted on three feed fractions: (1) shredded PCBs without any physical separation, (2) heavy fraction recovered from DMS, and (3) non-magnetic fraction recovered from the DMS heavy fraction. DMS increased the metal content in the feed from 48 % to 75 % on a mass basis, but 70 % of the gold and 20 % of the copper reported to the light fraction. The application of magnetic separation to the heavy fraction produced by DMS removed 67 % and 61 % of the iron and nickel, respectively, while negligible amounts of non-magnetic metals were removed. Although DMS successfully concentrated the feed and magnetic separation removed the majority of iron and nickel, these steps did not result in any improvement in the rate or extent of copper leaching. Metals generally leached faster when the sulfuric acid concentration was increased from 1 M to 2.5 M; this effect was seen to be more pronounced for pretreated feed. INTRODUCTION The fast rate of technological development has led to a decrease in the service life of electronic devices. This is resulting in an increased rate of electronic waste generation. The recovery of metals from electronic waste is of environmental and economic interest. The majority of these metals are typically located on printed circuit boards (PCBs) within electronic devices (Tuncuk, Stazi et al., 2012). Hydrometallurgical processes are considered a viable option for small scale metal recovery from waste PCBs, and generally involve the following steps: disassembly for removal of hazardous and reusable parts, size reduction, physical separation, successive leaching stages for metal dissolution and finally recovery of metals from leach solutions."

Jan 1, 2018

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By Irena Grigorova

"Vermiculite is a naturally occurring mineral compound composed of shiny flakes, resembling mica. Worldwide, vermiculite has been used in various industries since 1920. When heated to a high temperature, flakes of vermiculite expand several times their original size. The expanded vermiculite is a lightweight, fire-resistant, absorbent, and odorless material. These properties allow vermiculite to be used to make numerous products, as an additive, for example to potting soil, in agricultural, construction, horticultural and industrial applications, including pesticides, insulation, potting mixes, brake pads, sound deadening materials, fire protection, paints, sealants, insulating concrete and etc. Over recent years researchers have been looking for effective economic and environmental methods and solutions for fine technological waste utilization. As a result of vermiculite ore processing large quantities of fine waste dust are formed. Until now there has been no application for this waste product. Currently this waste product is stockpiled using valuable land space, and is a potential contaminant. The paper presents the results of a study on the possibility to obtain briquettes from fine vermiculite by-product. The particle size distributions, chemical and mineralogical compositions of vermiculite were determined. It was established that consolidation of vermiculite dust by methods of briquetting and its consequent application in agriculture as meliorants for physico-chemical treatment, improves soils aeration structure and properties."

Jan 1, 2014

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By A. V. Rasskazova

"The oxidized and mixed ores are processed by heap leaching. Primary ores with high gold content are floated. In recent years mining of primary ores with the low gold content (up to 4 ppm) has increased. Extraction of gold from these ores by floatation is technologically ineffective. Gravity concentration is ineffective for fine gold particles because of their floatability. The research objective was assessment of the viability of processing gold-bearing ore with combined gravitational and hydrometallurgical methods and testing of recovery of metals from a gold-copper oxidized ore chloride-hypochlorite leaching solution. The advantage of chloride-hypochlorite lixiviant is the low cost of reagents which is produced by the electrochemical synthesis of NaCl solution with the addition of HCl. The adsorption of chlorine compounds by a mineral matrix and its ability to oxidize the refractory ore components and allows for the application of chloride-hypochlorite systems for gold recovery for both oxidized and primary ores. The complexity and problem in using a gold–chloride system is the strong adsorption of gold–chloride complexes onto mineral surfaces, such as goethite, quartz, and alumina. In preliminary testing, gold recovery from gravity circuit gold bearing concentrates processed by agitation leaching in chloride-hypochlorite solution, gold recovery has reached up 82% after 4 hours of leaching. Chloride-hypochlorite leaching of copper-gold oxidized ore with preliminary processing by sulfuric acid provided for 94 % gold recovery to solution. Understanding of ecological hazard of cyanides is the motive power of researches in the field of search non-cyanic chemistries to provide for technologically and economically effective solvents of gold. Soluble compounds of chlorine with a suitable oxidizer are one of the alternatives to cyanides. Basic researches of gold extraction by chloride-hypochlorite solution have shown high rates of gold recovery.INTRODUCTION Because of the continued and growing environmental concern for the use of cyanide for gold processing, interest for the use of non-cyanide lixiviants, especially with halides has renewed recently (Tran et al., 2001; Ferron et al., 2003; Bhaghalha, 2007). Leaching solutions based on halides (chloride, bromide and iodide) are viable alternative to cyanide (Kwang et al., 2008). The major disadvantage of the chlorine–chloride system is the high reactivity of chlorine in reaction with sulfide and gangue carbonate minerals. It is believed that only high grade materials may be treated by chlorine–chloride systems economically (Baghalha, 2007). Another important problem of the application of gold–chloride complex is that it tends to be rather unstable and may re-precipitate upon contact with a reductant, such as sulfidic minerals of ore. It is well known that Au(III)–chloride hydrolysis species are strongly adsorbed by goethite, quartz, and alumina (Machfsky et al., 1991). To minimize adsorption of gold–chloro complexes, it works best to minimize the adsorption time."

Jan 1, 2018

By Peter Ay, Matthias Schmidt, Christian Stollberg

"The aim of the study is the development of a seamless reprocessing procedure for plastics from automotive parts which are to be recycled (figure 1). Before automatic sorting can be performed, the materials first have to be identified by a near and middle infrared (NIR/MIR) system.Materials reprocessing basically includes research on size reduction, decoating, and roughening of the materials. Variants of the necessary technologies such as different shredders and mills and physico-chemical or mechanical decoating and roughening procedures together with the fundamental approaches underlying these methods are investigated and benchmarked. This allows the theoretical determination of the impact of each method not only on the overall process but also on the result achieved within the identification and sorting procedures."

Jan 1, 2003

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

A new flotation system has been developed to improve the generally slow separating differentials of fine bubbles and fine particle suspensions. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. In the new system (see figure 1) this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.

Jan 1, 2003

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By Y. J. Ferdosi

This paper presents the outcomes of the preliminary investigation focused on the potential usage of Electrochemical Impedance Spectroscopy (EIS) in minerals processing. Currently, Electrochemical Impedance Spectroscopy has been successfully employed in the characterization of multilayer structures formed as molecules adsorb on flat surfaces and is commonly used in bio-related research. Few studies have explored the application of EIS in minerals processing, particularly for mineral particles and flotation systems. In the first series of tests, the impedance response was investigated as a function of particle size, shape and hydrophobicity using model quartz particles. The particle size fractions and the shape were found to contribute to the impedance response. The more hydrophobic quartz particles resulted in a higher impedance values. Further tests involved pure sulfide minerals including chalcocite, bornite, chalcopyrite and pyrite. The AC impedance measurements were conducted as a function of collector (sodium ethyl xanthate) dosage. The AC Impedance data was modeled using the combination of reference circuits. It has been shown that adsorption of collector onto sulfide minerals surfaces results in a higher magnitude of impedance. Increasing the collector dosage resulted in an increase in AC impedance for chalcopyrite, while a decrease was observed for chalcocite. Significant variations in impedance were exhibited by bornite and pyrite with a gradual increase in collector dosage.

Sep 1, 2012

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003

By F. Karakas

Water based paint formulations consist of some industrial minerals with quantities varying from 20 to 50 %. Quality of paint is directly related to these minerals used as pigment or filler in the production. Titanium dioxide is the most important and expensive pigment in paint formulations. Other minerals such as calcite and calcined kaolin are used as filler and mainly as a substitute for TiO2. Consequently, particle-particle interactions including adsorption, coating and size distribution of pigment mixture directly affects the paint quality. In the present paper, a new type of pigment mixture for possible use in architectural water based paints was developed through grinding. The effect of different types of grinding methods on physical properties of TiO2 and calcite mixture and the quality of paint produced by these mixtures have been revealed. Three different types of mills; conventional ball mill, vibratory ball mill and high-speed attritor were used for grinding of TiO2 and calcite. Viscosity, zeta potential and particle size distributions were used to characterize the pigment mixtures obtained upon grinding. The quality of paint was evaluated by standards based on both wet and dry paints such as viscosity, density, opacity and gloss. The paint produced with the pigment mixtures prepared in vibratory ball mill and high speed attritor showed improvement in physical properties particularly in the distribution and dispersion of mineral particles. Keywords: grinding, pigment, paint, TiO2, calcite

Sep 1, 2012

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By G. I. Voiloshnikov, V. E. Dementyev

"One of the most important advances in the world gold metallurgy is the introduction of adsorption technologies for processing of ores and concentrates. «Adsorbent-In-Pulp» process allows to eliminate pulp filtration that is especially important during processing of clay and slime bearing ores. “Adsorbent-In-Leach” process is one of the ways for processing of preg-robbing (carbonaceous) products. High efficiency, increased metals recovery, decrease in capital and operational costs, possibility of easy control and adjustment are the advantages of adsorption processes. Anion-exchange resins and activated carbons are used as adsorbents. This paper presents Irgiredmet experience on gold adsorption technology using both adsorbents (RIP, RIL, CIP, CIL processes). It includes results of long-term studies of different theoretical and practical issues of adsorption processes. Irgiredmet started development of ion exchange technology (RIP, RIL) in 1964. Laboratory and pilot plant tests were conducted to develop process design criteria for 15 RIP plants of the former USSR. During this test work a great number of newly synthesized resins including strong- and medium-base resins was studied, different types of adsorption feed (ores and concentrates) were tested; some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption for silver gold ore, improved flowsheet for gold elution and resin regeneration, designs of technological equipment for adsorption, elution, electrowinning processes including pulsation columns, electrowinning cells etc. were developed. Irgiredmet took part in commissioning of practically all RIP plants in the former USSR. Due to its efforts RIP process became to be the standard technology. Last Irgiredmet RIP projects include the development of adsorption technology using medium-base resin for the three mines owned by GC Petropavlovsk (Amur region, Russia). The complex of the testworks on activated carbon gold adsorption technology including the search of prospective activated carbons; study on gold adsorption mechanism; development, testing and introduction of process flowsheets and the equipment for their realization was conducted. The original gold elution process was developed. The developed CIP technology was firstly introduced at Lebedinsky gold plant (Yakutia). Now carbon adsorption technology is widely used at Russian gold mines as CIP, CIL, CIC processes. The most relevant example of CIP introduction is Svetlinsky gold plant (Ural, Russia) with capacity 8 Mt of ore/ year."

Jan 1, 2018

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012