Search Documents

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By C. L. Liao

The chief experiences for constructing deep tubular columns foundation under deep water are as follows: 1. P.C. tubular columns were sunk inside the caisson. 2. P.O. tubular columns of 3.6 M. diameter were sunk thru thick soil layer to a depth of 47 M. by vibrators. 3. The double wall steel cofferdam was sunk thru soil layer to a depth 31.3 M.. 4. Bore the bedrock with rotary drill succesfully. According to the successful experiences mentioned above, the deep tubular columns foundation may be constructed beyond 100 meters.

Jan 1, 2010

By M. R. Madhav

The ultimate pullout capacity of single batter piles has been presented in literature in three contradictory trends. These trends are: the pullout capacity of a single batter pile increases, remain almost constant, or decrease with increasing the inclination angle of the pile. The present paper presents a theoretical study which explained these trends in terms of existing initial stress condition and the earth pressure coefficient at rest. The paper also presents a form of guideline for predicting the pullout capacity of inclined piles based on simple field and/or laboratory tests.

Jan 1, 2010

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Daniel Stevenson, Richard Guenther

"The preservation of historic buildings is not only essential to the understanding of our national heritage, but it is also environmentally responsible to adapt existing buildings to compatible new uses. With this perspective, the American Enterprise Institute began exploring options to expand the newly acquired Andrew Mellon Building, located at 1785 Massachusetts Ave. NW in Washington, D.C., without causing any harm to the Beaux Arts style limestone façade and its plaster interiors. The building is a National Historical Landmark, but its 72,000 sq ft (6,690 sq m) of usable floor space did not meet the needs of its new owner. The building perimeter is very near the property line, so horizontal expansion was not possible. Adding height to the building was not an option, as this would have altered the historic nature of the building exterior. The only feasible option that could provide the desired floor space was to add a new floor underneath the existing structure. By adding a level beneath the existing building, an additional 28,000 sq ft (2,601 sq m) of floor space could be produced.Berkel & Company Contractors was chosen as the deep foundation/shoring contractor tasked with ensuring that the existing structure was stable and remained undamaged during the excavation and construction of the new lower level. To accomplish this, Berkel provided a shoring system that would act as both excavation support and permanent deep foundation elements for the final structure.Preservation of the existing limestone façade and plaster interiors was critical to the success of the project, as additional foundation settlements could damage these irreplaceable building components. Project specifications, therefore, included very stringent limits for foundation settlements. The maximum allowable total settlement for all existing building walls and columns was ¼ in (6 mm) for the duration of the project."

Jan 1, 2017

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By John Kvinsland

"The Block 43 Project is the future home of the Paul Allen Institute for Brain Science located just off the southern shore of Lake Union in Seattle, Wash. The South Lake Union (SLU) district experienced considerable development over the last 10 years and Vulcan, Inc., which is headquartered in Seattle, is at the forefront of this transition. Once a light industrial/residential location, SLU has transformed into a hub of medical technology comprising new residential units and mixed-use buildings. Malcolm Drilling Company, Inc. constructed four shoring projects for Vulcan in this vicinity over the last year, beginning with Vulcan Block 44, which consisted of 42,000 sq ft (3,902 sq m) of soldier pile and tieback wall to support a below-grade parking facility. Block 44 construction began in February 2013 and ended in mid-April. The feature project, Vulcan Block 43, was in planning stages at the time and began construction in late fall 2013.Awarded by GLY Construction of Bellevue, Wash., in September 2013, Block 43 was the most complex of the block projects performed by Malcolm. Block 43 featured dewatering and ground improvement components along with a water-tight secant pile wall. Following the commencement of Block 43, Malcolm also began work on Vulcan Block 52 in December 2013. Block 52 consisted of 43,000 sq ft (3,995 sq m) of conventional shoring in conjunction with dewatering of 8 ft (2.4 m) of excavation located below the water table. The final Vulcan project was Block 45, which started in January 2014 for Turner Construction of Seattle and consisted of 41,000 sq ft (3,809 sq m) of conventional shoring and required dewatering to complete the final 15 ft (4.6 m) of excavation.Scope and Subsurface ConditionsBlock 43 involved a wide variety of drilling applications for the building to be constructed and properly founded. The primary scope of work involved shoring support for an underground parking structure requiring excavation of approximately 82,000 cu 3 yds (62,694 m ) of soil. The cuts for the excavation were up to 43 ft (13.1 m) in depth, and the excavation was bounded by city streets as well as the South Lake Union Light Rail on its perimeter. In order to excavate beneath the water table, an extensive, deep dewatering system was required to drain the upper fill and reduce the impact of the pressurized aquifer located beneath the excavation. In addition, drilled rigid inclusions, along with compaction grouting, were required for foundation support of the future structure."

Jan 1, 2014

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Kyle R. Lackner, Jared P. Williams

"The Sutter Butte Flood Control Agency initiated the Feather River West Levee (FRWL) Program in 2010 to bring 35 miles of levee along the Feather River into compliance with applicable Federal and State standards for levees protecting urban areas. A combination of soil-bentonite cutoff walls, soil-cement-bentonite cutoff walls, and seepage berms will reduce flood risk by correcting under and through seepage deficiencies and remove more than 34,000 properties from the FEMA Special Flood Hazard Areas. The FRWL program includes a combined total of 7,744,803 square feet (SF) of cutoff wall planned to be constructed between 2013 and 2015. Cutoff wall construction methods to meet the design depths included conventional excavation to a depth of 85 feet and deep soil mixing for depths up to 120 feet. A key component of the FRWL program was the development of site specific mix designs using the design boring logs to evaluate the expected backfill gradation and permeability results. Issues that required a partnership between Contractors, Owner and Engineers included substantial Archaeological and Cultural Resource delays, significant depth changes due to a change in competent key, right of way acquisitions for abutting land, and the magnitude of the project in a resource limited industry.IntroductionThe Feather River watershed basin is located 50 miles north of Sacramento, CA and incorporates the agriculture producing communities of Yuba City, Live Oak, Gridley and Biggs. These communities are protected from flooding by levees that contain under-seepage and through-seepage deficiencies and were the cause of major failures in 1955, 1986 and 1997. The Feather River West Levee (FRWL) program was initiated by the Sutter Butte Flood Control Agency (SBFCA) in 2010. The long term objective of SBFCA is to correct the levee deficiencies and provide 200 year flood protection to more than 34,000 at risk properties located within the FEMA Special Flood Hazard Areas.Although FRWL contained a variety of construction components such as earthwork and pipe replacement, the slurry cutoff wall is the primary construction element for addressing under and through seepage deficiencies. From 2013 to 2015 approximately 6,649,210 SF of cutoff wall were installed using conventional excavation and deep soil mixing (DSM) techniques leaving 1,095,593 SF to be completed in 2016. The work was designed, solicited and constructed under two separate contracts, titled Project Area C and Project Area B&D. A summary of the contracts and cutoff wall quantities is presented in Table 1."

Jan 1, 2016

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005