Search Documents

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Anthony L. Reynolds, Clifford J. Wren

"The adoption of a significant pile testing regime, the use of Eurocode 7 as the design standard, the development of lean construction techniques, and lateral thinking in overcoming some considerable construction challenges allowed Stent Foundations to construct the foundations for the new Wembley Stadium, London, on time and within budget. In addition to the piling works for the main stadium, and after significant design development, a large number of extra piles were required to raise the new iconic roof Arch to its final position some 133 metres above the ground. A 1,400m long contiguous bored pile wall was also constructed to allow for excavation and formation of the new pitch. INTRODUCTIONHjstorjcal lntrodyctionWembley Stadium is the 'home of English football'. As long ago as the 1880's, Wembley Park leisure grounds had football pitches and running tracks.In 1918 the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Exhibition area covered 219 acres and the area on which a former abandoned tower called Watkins Folly had stood was chosen as the site for the new stadium (http://www.wembleystadium.com).The Empire Stadium, as it was originally known, was designed by architects Sir John Simpson and Maxwell Ayerton and the engineer Sir Owen Williams. It took just 300 days to complete at a cost of £750,000 ($1.4m), and was built using 25,000 tons of ferro concrete, 1,000 tons of steel, and over half a million rivets.The Empire Exhibition was a remarkable event, containing fountains, lakes, gardens, and many pavilions, each representing the architectural style of the countries exhibiting. It was opened on 23rd April 1924 and the final attendance was over 27 million, with 4.5 million admissions to the Empire Stadium alone."

Jan 1, 2005

By Andreas Brandner, Karl Schoenherr-Strasse, I. B. Brandner, Dipl. Ing

"A world famous Wintersport resort in the Alpine planned to build a parking garage for more than 600 cars and busses situated between a torrent, a district road and the village.A nearly 200 m long building giving place for 6 parking levels and a maintenance level for busses and trucks is situated alongside a hill causing excavation height between 20 and 25 meters, which had to be secured. Due to restrictions – neighbours did not allow the client to drill anchors for retention – we designed a solution combining micropiles, strand anchors, shotcrete and nails as permanent earth retention not exceeding the space of 7 meters provided by the local street. Soil conditions were as challenging - reaching from backfill to moraine with boulders of more than 20 m³ volume – as the construction period of total 12 months for the whole project, which was opened mid of November 2015.The innovative solution outperformed the client´s project from the technical and commercial aspect and helped the contractor to save time and money.The design process with its difficulties as well as erection process is described in the following paper."

Jan 1, 2016

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By Bao K. Le, Khang T. Truong, Masaki Kitazume, Toru Kobayshi, Long P. Le, Tanaka Hitoshi, Makoto Kamimura, Hoang-Hung Tran-Nguyen

"Earth levees constructed using dredged materials taken from a river along an earth levee have annually damaged in the Mekong Delta due to high void spacing in earth levees and floodwater. Sliding and internal erosion due to floodwater or piping are two key factors causing earth levees’ failures. This study proposed to apply Deep Mixing Method (DMM) to reinforce earth levees in the Mekong Delta, Vietnam. The DMM creates a soil cement wall or soilcrete wall having better engineering properties such as higher strength and low hydraulic conductivity than those of the in-situ soils. The DMM can be applied to reinforce earth levees with limit additional materials that provinces in the Mekong Delta are difficult to supply. The study investigates capacity of the DMM to reinforce earth levees in the Mekong Delta, Vietnam against annual floods. Seepage and slope stability analyses under various conditions were performed with various scenarios of earth levee’s body. The analysis results indicate that the DMM can create a wall that cuts off piping across earth levee significantly and can improve stability against deep sliding due to rapid drawdown of the floodwater.INTRODUCTIONThe Mekong Delta produces agriculture products of 50% of the whole country even though the Mekong Delta has an agriculture area of 30% of the country (Wikipedia 2014). Rice is the main product for the domestic demand and export. This is the main reason why the local people want to cultivate rice 3 times per year to increase the total rice product for export. To do that, the local provinces have constructed earth levees surrounding each area of 100-200-hectare against annual floods to protect rice fields, and farmers can grow rice in the whole year. There are thousands of kilometers long earth levees in the Mekong Delta, and the local governments have spent millions of US dollars to repair and to maintain their earth levees yearly (reports of Dong Thap province 2012; 2014).Earth levees in the Mekong Delta have often failed in flood seasons (e.g., from August to December), especially in Dong Thap and An Giang provinces – the two provinces confronting directly the annual floods from the Mekong River when the floods reach the Vietnam land. The main failure of earth levees is piping, and then causing collapse of some section of an earth levee. An earth levee was usually constructed by piling up dredged materials along a river with minimum compaction. Subsequently, floodwater flows through connected void spacing and washes out soil particles in the body of an earth levee slowly to create piping. Annual wet-dry cycles make the top clay layer swelling and shrinking to form cracks that can store rainwater to trigger sliding (whitlow 2001; Ton That Vinh 2003)."

Jan 1, 2015

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Y. Z. Xu

This paper presents a new dynamic method called Resonant Pile Test (HPT) for evaluating bearing capacity of pile. The basic conception of RPT is given in brief and the measuring system is also introduced. In addition, the influences of the magnitude of exciting force and of the mass of pile cap on test results are discussed. Finally, comparisons between values of bearing capacity given by RPT and by static load tests for a variety of pile types are listed.

Jan 1, 2010

By Giovanni A. Bonita, Asher H. Peltz, Sean D. Johnson

This paper examines a complex earthwork project in the Washington DC metro area that had project delivery directly impacted by questionable instrumentation monitoring data. The case study summarizes the impacts to the project caused by questionable instrumentation data and reveals how the authors were able to utilize data to extract meaningful insights. The case study also demonstrates how clear data presentation became a key factor in maintaining stakeholder trust and facilitated progress of the project schedule. The case study highlights key points to collecting high quality instrumentation data, approaches to assess and improve value of the data collected, and techniques to reduce and interpret questionable data.