Search Documents

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 8 to 12 feet in diameter and extending over 200 feet in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2013

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Jim Henry

I would say mainly the cost. I showed only 3 cases. One of them was the one that Allen just described and there were two other cases. In those cases it was fairly easy to develop a solution using limited mobility grout to treat the soft soils suitable for the limited bearing pressures required by the structures. LMG readily provided a fairly reliable system for the foundation support at a reasonable cost.

Feb 10, 2003

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Wanchai Teparaksa

Pile deviation generally can happen after installation of driven pile particularly in soft soil layers. In this case study, all 242 diameter 0.8 m spun piles were deviated from 20 to 820 mm. The large deviation was caused by lateral soil movement in the top very soft clay layer of thickness about 23 m. This very soft marine clay is very sensitive and anisotropic having high water contents of over 120% and low undrained shear strength of 5-10 kN/m2. The remedial works were carried out based on theory of load transfer and soil-structure interaction. All deviated piles were rectified and used as the foundation piles with strictly controlled pile load tests. The construction of a nine-storey building was successfully completed founded on the rectified piles and it has been opened for the service for over two years.

Jan 1, 2002

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By Rob Jameson

"Although seismic retrofit is recognized as a key micropile application, widely-used reference documents do not clearly address design and testing recommendations for micropiles that are loaded primarily under seismic conditions. The principles of micropile design and construction and their application to seismic retrofit projects are well understood and executed by leaders in the field. As the micropiling market grows, a wider audience relies on the information presented by DFI and similar industry groups. State-of-practice updates appear periodically in conference proceedings, but examination of recent bid documents makes it clear that there are opportunities to improve the specification of load, deflection, testing and acceptance criteria on many seismic retrofit projects. Updates to the FHWA Manual or DFI Sample Specification that specifically address seismic retrofit cases would be useful tools to disseminate information and enhance the state of practice.Micropile Survey UnderwayAs one step in this process, I am distributing surveys to contractors and designers prior to DFI Super Pile ’09 (June 4-6, San Francisco) seeking recommendations for design and testing procedures applicable to seismically loaded micropiles. I am also requesting any existing references that could be promoted as a standard for these cases. Anyone interested in participating in this survey, should contact me at rjameson@malcolmdrilling.com. Seismic RetrofittingMicropiles are ideally suited to seismic retrofit applications. Their high-tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. They can be installed within and around the access limitations of existing structures, and can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones.Seismic retrofits have included micropiles since the early 1990s, and they are now widely specified in the Western U.S. In the San Francisco Bay Area alone, thousands of micropiles have been installed for seismic upgrades of highway and transit aerial structures, and retrofits of commercial, residential and public buildings. Micropile use is growing in both public and private sectors, with large-scale retrofit projects currently underway for both the Bay Area Rapid Transit (BART) system-wide upgrades and renovations at San Francisco Airport."

Jan 1, 2009

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect projectspecific requirements. The commentary should be removed before using the specification for a project.1. SCOPEThe work consists of designing, furnishing, installing, post-tensioning and testing helical anchors used to support tension loads, and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment, and materials necessary to accomplish the work. The parties referred to in this specification are as follows:• The Owner is the property owner.• The Owner’s representative is the individual or firm hired by the Owner to execute project tasks required for the successful design and construction of the overall project. Tasks could include construction management, design, oversight, etc.• The anchor designer is the individual or firm generally hired by the installing contractor to design the helical anchors.• Installing contractor installs and tests (if necessary) the helical anchors, and possibly other tasks associated with the project.It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development.The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of anchor performance if required by the Owner or the anchor designer to confirm performance of the anchors subsequent to their installation. The work may also include installation of additional anchors if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2016

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Charles M. Wilk

"Solidification/stabilization (S/S) treatment is used to treat hazardous wastes for disposal and in the remediation/site restoration of contaminated land . SIS is also an increasingly popular technology for Brownfield (industrial property) redevelopment, since treated wastes can often be left on-site and to improve the soil for subsequent construction. This paper discusses the applicability of the technology to various wastes, basic cement chemistry relating to SIS, tests used to design treatability studies and to verify treatment, basics on implementation of the technology in the field , and examples of SIS use at brownfield sites, including a former wood preserving site, former manufactured gas plant sites, a former electric generating station, and a shopping mall development.INTRODUCTIONSolidification/Stabilization (S/S) is a widely used treatment for the management/disposal of a broad range of contaminated media and wastes; particularly those contaminated with substances classified as hazardous in the United States. The treatment involves mixing a binding reagent into the contaminated media or waste. The treatment protects human health and the environment by immobilizing contaminants within the treated material. Immobilization within the treated material prevents migration of the contaminants to human, animal and plant receptors. SIS treatment has been used to treat radioactive wastes since the 1950s and hazardous waste since the 1970's (Conner 1990). SIS continues as a cornerstone treatment technology for the management of radioactive waste, hazardous waste, and site remediation and Brownfield redevelopment."

Jan 1, 2005

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Martin Walker, Joseph Ang, Jongwon Lee, Alvin Bayudanto, Lilian Lorincz, Morteza Khorshidi, Wenyong Rong

This paper presents a case history of liquefaction susceptibility evaluation study for a major infrastructure project in the San José area. The subsurface material of the study area consists of Holocene alluvial deposits composed of interbedded and crosscut clays and silts, sands and gravels. The simplified approach for liquefaction triggering evaluation was carried out using both CPT data and SPT data representing site’s seismic capacity and the peak ground acceleration associated with a return period of 975 years at ground surface representing seismic demands. Site-specific cyclic stress ratio (CSR) profiles as seismic demand are also estimated from one-dimensional site response analysis. The simplified approach uses empirical depth stress reduction factors (rd) based on generic shear wave velocity profiles to account for the non-rigid response of the soil profile in estimating CSR. The CSR profiles of the simplified procedure were examined by completing site response analyses using site-specific soil profiles to represent site-specific seismic demands in the liquefaction triggering evaluation. The paper concludes with a comparison and discussion of the liquefaction evaluation examining results from CPT versus SPT data, and the comparison of CSR profiles from the simplified procedure versus site-specific response analysis.

Sep 8, 2021

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021