Search Documents

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

By D. M. Baird

Copper mineralization occurs at several places along the shore of Notre Dame bay, Newfoundland, and at one time formed the basis of a considerable mining industry. The sources of the mineralizing solutions and the structural settings of some of the deposits have not been clearly understood. This paper reports new investigations into the origin and structure of the deposits between Bett's cove and Stocking harbour, in a strip about ten miles long and two miles wide along the western shore of Notre Dame bay. The most complete previous descriptions of the area are those of Snelgrove (1929, 1931, 1938), Douglas, Williams and Rove (1940), and the writer (1947). The discovery of the Bett's Cove deposits took place about 1860, soon after the discovery of the well-known Tilt Cove deposits to the north. Several other small prospects were found between Bett's cove and Stocking harbour between 1880 and 1910. At Bett's cove, active mining began in 1875 and a small smelting plant was built near the mine in 1877. .Mining operations came to an abrupt halt in 1883 after a major cave-in. In 1900, and again in 1906, attempts were made to drain the old workings and reopen the mine but were abandoned long before completion. Total production amounted to about 130,000 tons of hand-picked copper ore which averaged about ten per cent copper, and 2,450 tons of pyrite (Snelgrove, 1938, pp. 52-55).

Jan 1, 1948

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By F. Rosenblum, P. Spira

A laboratory test has been developed for assessing the patential hazard from self-heating of sulphides. The technique consists in measuring the rate of self-heating, from near ambient temperature, of a 1-kg sample in an insulated chamber controlled at standard atmospheric conditions. The rate of oxygen consumption is monitored simultaneously. The paper describes the apparatus and test procedure, and reports data on various ores and mill products. Tailings known to have caused problems underground when used as backfill have shown heating rates of over 3°C/h. A preliminary hazard rating guide for backfill based on the known behaviour of several sulphide materials is presented.

Jan 1, 1981

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By I. Imris

The chemical industries are using different type of catalysts, which after application usually produced many tons heap of residues. One of them is cupric oxide catalyst with high content of copper and silica. The recovery of copper from the waste has become major interest from a viewpoint of environmental protection and recycling of resources. The thermodynamic analysis and experimental results suggest that the copper from cupric oxide catalyst can be extracted by plasma reduction process. By plasma reduction process the inert slag and copper with following chemical composition: 99.04 % Cu, 0,042 % Fe could be obtained.

Jan 1, 2007

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By Claudia Gasparrini

"The ore microscope and electron microprobe, two common instruments for academic research, have not been used to full advantage in the Canadian mining industry, perhaps because they are not readily available to most mining companies.The present paper gives a description of the two instruments and of the manner in which, when used together, they contribute to the identification and description of mineralogical and metallurgical samples, and reviews the applications, to . date, in the mineral industry.The metallurgical applications can assist in determining the best separation technique for a particular metal or other economically important element, can provide explanations for poor recovery and/or liberation, can be used to determine theoptimum concentrate grade and can indicate environmental problems that may arise from the extraction process.In certain cases, the use of the two instruments may assist in the evaluation of new mineral deposits and in the determination of the origin of mineralization.IntroductionThe ore microscope and electron microprobe, two widely used instruments in universities and other research institutions, have not been exploited to their full potential by the Canadian mining industry.High-magnification, high-resolution ore microscopes, owned by most Canadian universities and government mining branches, are not widely used by mining organizations. The situation is very much the same with the microprobe. The geology departments of several major Canadian universities have easy access to this instrument. Fifteen of them, to the author's knowledge, own one and a few have already acquired or are planning on acquiring a second and later model. The mining branches of the Canadian Government have similar easy access to microprobes, as at least four of these instruments are available to them in Ottawa alone. The mining companies, on the other hand, except for the few larger ones which have their own research laboratories, have not been able to take advantage of electron microprobes in the past.This failure to exploit good ore microscopes and electron microprobes has been mainly due to a lack of expertise in the use of the two instruments for the study of metallurgical problems related to ore mineralogy. Government institutions providing research and test work to the industry are few in number, and are not always equipped with these instruments or are not geologically-oriented. Information provided on a consulting basis by universities and by government mining branches is normally limited, and frequently is not oriented to the needs of the mining company."

Jan 1, 1980

By Daniel Hodouin, Robert Lanthier, Yve Dube

"A procedure f or constructing a grinding mill dynamic model is proposed. This model is used in a dynamic simulator of are grinding circuits. The simulator is designed for flexible flow sheets involving different grinding mills and particle classifiers and is able to accept several single variable PID control loops. The dynamic model is validated on a laboratory ball mill, and calibrated to an industrial installation. The simulator is used for characterization of grinding circuit dynamic behaviour and tuning of control strategiesIntroductionThe ore grinding operation is a critical step of the ore preparation process because it is the last comminution stage before the separation of minerals. The properties of the ground minerals to be concentrated, control the quality and efficiency of the separation process. This is why it is important to control properly the operation of the last grinding stage, commonly constituted of a closed circuit ball mill with classifier . To provide an adequate fine product, the grinding operation should compensate for the perturbations of the feed characteristics (size analysis, grindability, etc.). The main objective is to maintain a constant size distribution for providing stable operating conditions to the separation units. Simultaneously another usual objective is to operate the grinding circuit at a maximum capacity.Automatic control applied to grinding circuit s is the appropriate approach to improve its operation. Most frequently average optimal operating conditions are determined from steady -state performances of the circuit , and the automatic control is used for stabilizing the operation at selected values of the process variables . In the traditional approach, one or several single input! single output (SISO) control loops are implemented and empirically tuned. Advanced control practices'!' are based on a quantitative analysis of the circuit dynamics, which could also give a basis for the tuning of conventional SISO 100ps(2)."

Jan 1, 1987

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By J. C. O'Rourke

"Gibraltar Mines Ltd. has been operating its open pit copper mine for fifteen years. In that time, over 140 million tons of waste and low-grade material has been placed on the mine waste dumps. Laboratory and in situ testing indicated that enough leachable copper was recoverable from the dumps to justify a leaching operation which would include the construction of a solvent extraction-electro winning plant. The plant, which was commissioned in October 1986, was designed to process 3000 USGPM of dilute copper solution to produce 5000 tons per year of high-quality cathode copper.This paper deals with the start-up and initial year of operation of this plant. The three areas: leaching, solvent extraction, and electrowinning are presented with emphasis on the innovations which were made to help overcome the problems unique to the Gibraltar operation.The Leaching CircuitThe mine waste dumps are leached to produce a pregnant copper solution as feed to the SX-EW plant. To achieve this the dumps are sprinkled with a mildly acidic solution which percolates through the dumps. In travelling through the dumps the solution contacts the surfaces of the liberated copper minerals and dissolves the soluble copper into the form of copper sulphate. The leaching reaction is achieved by a combination of bacterial action to oxidize the sulphides and solubilization of the copper into the acid solution.For the bacterial action to occur the dumps must be near the ideal pH of 1.9 to 2.1 and the necessary elements of the reaction must be present. Because a bacterial reaction is involved there is a lag time between the time when the conditions for bacterial growth are achieved and when the bacteria are in their active growth phase. Laboratory leaching tests with Gibraltar ore indicated that bacterial action takes two to three months to reach its maximum rate (Fig. I).The expected lag time for the planned rate of bacterial leaching prompted Gibraltar to start irrigating the dumps in late June 1986 for a plant start in early fall. The lag time proved to be longer than expected and the dumps took until November to start producing copper at the expected rate (Fig. 2)."

Jan 1, 1988

By I. B. Schalamuk, R. E. de Barrio, M. J. Pons, M. B. Franchini, L. Meinert

"Several Fe, Fe-Cu, and Cu-Ag prospects hosted by Mesozoic carbonate-rich sedimentary rocks that were intruded by diorite stocks define an approximately 20 × 200 km belt along the Andes Cordillera of southwest Mendoza province, Argentina (34°-36°S). This belt includes the Hierro Indio and Vegas Peladas Fe skarns, Las Choicas, and several other Cu-(Ag) prospects.The main features of the Fe skarns include: association with mantle-derived middle Miocene (~15-11 Ma) diorite stocks and sills; widespread alteration including epidote ± amphibole ± magnetite endoskarns, and zoned garnet (Grs0-66 Adr32.5-100) ± magnetite ± pyroxene (Di24-50 Jo2-9 Hd74-41) exoskarns formed from oxidized, saline, high-temperature brines (530º-660ºC; 60-70 wt.% NaCl equiv.); and magnetite-hematite orebodies associated with quartz ± epidote ± calcite ± actinolite formed at lower temperatures (290º-436ºC) from saline fluids (32-50 wt.% NaCl equiv.) of magmatic origin.West of the Fe skarn belt, the Valle Hermoso district covers more than 300 km2 and hosts several poorly known Cu-(Ag) prospects (estimated 30 Mt with 1.5% Cu and 20 g/t Ag). These prospects share many characteristics with the iron oxide copper-gold-type systems and manto-type Cu deposits of northern and central Chile. One of the prospects (Las Choicas) is located at the apex of a regional 015°-trending anticline, along the contact of stratified calcareous sandstone and limestone (Neocallovian-Oxfordian) with a diorite pluton. This pluton has positive Ta and Nb anomalies (on normalized diagrams) and a high Ti content, features uncommon in Miocene diorites associated with Fe skarns and of magmas derived from sub-arc mantle sources. Alteration at Las Choicas includes early widespread chlorite + calcite ± albite ± scapolite ± ilmenite or titanite ± apatite, and local actinolite ± hematite ± biotite alteration of diorite and sedimentary rocks along contacts. Later Cu mineralization (1%-10% Cu) is associated with calcite ± albite ± quartz alteration in fractures, vein networks, and crackle breccias. Mineralization is zoned from bornite ± chalcopyrite ± millerite with Zn, As, Mo, Ag, and U anomalies in the main orebody, through chalcopyrite-rich breccias with Zn anomalies, and chalcopyrite ± tetrahedrite vein networks with Sb, As, Ag, and Zn anomalies in the uppermost zone, to a Cu-depleted pyrite-rich envelope with Co anomalies, and finally to late, barren calcite veins in distal zones."

Jan 1, 2007

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By O. C. Rojas, J. Sanhueza, J. C. Vargas

Empresa Nacional de Minería (ENAMI) is dedicated to the promotion of small and mid scale Chilean mining industry. Paipote, ENAMI Copper Smelter, processes a variety of mineral products as the result of this promotion. The mineral products characterize a wide variation of copper, iron, sulfur and precious metals content as well as the significant dispersion in the content of impurities, such as arsenic, antimony and bismuth. The Smelter Modernization Program, initiated in1997, introduced a series of technological and operational changes. The development of operational planning and control strategies was necessary to optimize the blending of a wide variety of concentrates and the control of metallurgical processes in order to ensure the stable operation, fulfillment of environmental regulations and the quality of produced copper anodes. A permanent optimization process carried out in the last decade led to the permanent increase of the smelting capacity and the production of anodes and sulfuric acid. Additionally, introduced improvements affected the smelter efficiency and metallurgical recovery, demonstrating the possibilities of the optimization of a small smelting facility reflected in good metallurgical and economic results. This paper presents the smelter evolution, introduced technological and process control changes as well as incorporated new reactors and equipment as a continuous process of optimization.

Jan 1, 2007

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015