Search Documents

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y' and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By M. Vaccarini

In this paper a possible methodology to supplement a predictive control approach is reported. The benefits deriving from the application of a predictive control on complex buildings lay on its capability of adapting in advance to the conditioning needs of indoor environments. In fact, the mere reactive control is usually affected by response delays, mainly determined by latency intrinsic in systems and by the massive nature of buildings, which slows down their response to changeable inputs. Hence, systems are too often solicited at their maximum power to recover against comfort deficiencies, and high consumptions are had. This paper reports on the application of a predictive approach to the Passeig de Gracia (PdG) metro station in Barcelona, which is a considerably high energy demanding building and where ventilation systems are used to control both comfort and air quality. Although an extensive simulation for estimating energy savings obtainable through that approach is currently ongoing, in this paper we detail the several components which make up a ?predictive control framework? and we perform a preliminary demonstrative simulation. In particular, the whole setup is formed by: a detailed model of PdG, which simulates the station?s ?real state?; a control model, which optimizes a given cost-function; probabilistic predictive models to infer the future state of the systems, given the assumptions on the control actions by the control module. The outcomes of this paper show that the procedure is applicable and preliminary results over a short simulation horizon of half a day are reported.

Aug 1, 2013

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By P. H. Willis

Since the 14th CMMI conference, held in Edinburgh in 1990, at which a paper was presented by the author (Willis, 1990) reviewing the role of integrating new technology as a survival strategy for South African gold mines, considerable change has occurred in the South African mining industry. This paper reviews the current state of the industry and provides an update on the technologies discussed ten years ago. It reviews available technology and provides a broad economic assessment of these technologies if they were to be introduced in an integrated mining system with a focus on deep level mining below 3000 m. It also reviews possible future technologies currently being researched and developed by CSIR: Division of Mining Technology (Miningtek).

Jan 1, 2000

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By P. Gautier

Current feedstock in the aluminum hot forging processes can be used in the cast or extruded forms. The microstructural variation between as-cast and extruded materials could result in different mechanical properties and corrosion resistance for hot-forged products. Corrosion performances were examined for forged parts produced by two AA6082 feedstocks at different conditions using the following corrosion tests: open circuit potential, anodic polarization, salt spray exposure and corrosion fatigue. With the help of optical and scanning electron microscopes, metallographical investigations were carried out on cast-forged and extruded-forged materials before and after corrosion. The corrosion behavior of both materials was compared in both as-forged and aged tempers. Results show that there is no significant difference in the corrosion performance for final cast-forged and extruded-forged products.

Jan 1, 2011

By Aalbert Zwijnenburg

One of problems connected with the use of gold/titania-based catalyst systems is the low yield in propene oxide (up to 2 wt %). It is shown that the low propene oxide yield is due to product inhibition. New options for propene epoxidation with hydrogen and oxygen are discussed. INTRODUCTION The direct gas-phase synthesis of propene oxide (PO), by the use of molecular oxygen, is still aimed for. Agbased catalysis is in principle possible, but selectivity at present is not promising. Highly dispersed gold on titanium containing catalysts show an extraordinary selectivity in the oxidation of propene to the corresponding epoxide (> 99 %), using a combination of H2 and O2 as oxidation mixture [1]. Additional studies of the epoxidation reaction have indicated several drawbacks of the Au/TiO2 catalyst. Firstly, the low conversion (1- 2 %) obtained under typical reaction conditions (atmospheric pressure, 323 - 423 K) cannot be increased by increasing the reaction temperature, because this leads to extensive by-product formation. Secondly, the low efficiency of hydrogen (relatively large amounts of water are formed) is hard to prevent. Finally, significant deactivation of Au/TiO2 catalysts within several hours on stream has been observed. Deactivation can be almost completely prevented by using dispersed TiO2 supports, such as TiO2/SiO2 and Titanium-Silicalite-1 (TS-1) [2]. In recent literature [2,3] a hydroperoxide-like intermediate has been proposed to be responsible for the selective epoxidation. This oxidising species is said to be formed over gold and subsequently used for epoxidation over the Ti-containing support. The support is responsible for the slow desorption of PO. One of the problems for future industrial application might be the low yield in propene oxide. Furthermore, the presence of minor amounts of by-products, not detected on lab-scale catalyst testing, might complicate the separation unit in an industrial process. The reason for the low PO yield over Au/TiO2-based catalysts will be discussed in this paper. Temperature Programmed Desorption (TPD) and micro-flow experiments have been carried out to study PO desorption and catalyst performance, respectively. A catalytic cycle is proposed together with its consequences for the maximum yield in PO. Finally, several process and catalyst options are discussed in view of potential future industrial application.

Oct 1, 2003

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Mike Robotham

Drum hoists in the 21st century have the same fundamental objective as their earliest 19th century counterpart. And yet a lot has changed in the design of the hoist from those early days of underground mining. These changes are driven by the need for greater productivity and reliability at ever increasing depths without compromising the all important safety demanded by the industry today. This paper reflects on how these changes have influenced design of a modern hoist Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2013

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By Michel Ruel, Ali Soltanzadeh, Benjamin Légaré

High fidelity commercial process simulation packages can be used at different stages of a greenfield project, from initial plant design to operator training in the later stages. However, there are several factors that make the software less attractive for small and medium size brownfield projects, such as the licensing cost and the fact-finding manpower required for model design and simulator maintenance. In this paper a different approach is described. The knowledge gathered from operating personnel was used to implement higher level models based on plant data, operating heuristics, and experience rather than detailed component-level models. The computing platform used was a low-cost, well-established, control system vendor-independent software. Throughout this paper we demonstrate the success of implementing this model-based approach using two industrial examples. The first example is a simulation of the carbon monoxide (CO) distribution system at a metallurgical complex. The purpose of this simulator was to test new control strategies and PLC programs prior to implementation. CO being a toxic combustible gas, validation of the suggested control system changes was necessary for plant safety. Simulation of specific operating conditions helped alleviate concerns and improved plant-wide acceptability of the new operating philosophy. The second example is a boiler simulator at a petrochemical plant. The operator training simulator (OTS) was designed as a platform for experienced operators to practice handling rare or abnormal conditions. A customized medium-fidelity model was developed for this targeted application where the cost of a full scale high-fidelity model could not be justified.

Jan 1, 2016

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By T. G. Phillips

"This paper gives an inside look at a bulk terminal and describes the preparations that must be made by a company in developing such a terminal and its position in today's traffic pattern. The following headings cover the subject material: (a) Traffic pressures, their detection and measurement, (b) position in the traffic flow -selection of site, (c) transportation connections -present and possible future routes, (d) engineering studies and costs, (e) contracts, the basic material for insured traffic, (f) financing, (g) budgetary control, (h) development of new techniques, (i) growth into new cargoes or cargo-handling methods and (j) consolidation."

Jan 1, 1968